Cut Sheet

Wall HeaterW Series
Dimensional Data
=knockout location
MINIMUM CLEARANCE: Zero clearance to insulation 4" above floor 6" from adjacent wall
Engineering Specifications
Contractor shall supply and install W Series in-wall mounted forced-air electric heaters manufactured by King Electrical Mfg. Company.
Heaters shall be of the wattage and voltage as indicated on the plans.
Ratings: Wattages of 500 to 2,000 at 120, 208 or 240 Volts
are available. Heaters shall provide air movement at 85 CFM.
Fan and Motor: Motor shall be shaded pole, permanently lubricated,
C-frame type with impedance protection and sealed bearings. Motors
shall be the same voltage as the heater. The motor and all wiring shall
be totally isolated from the heating chamber for protection from heated
air. The motor shall be equipped with a dynamically balanced four-blade
aluminum impeller fan, located in the upper portion of the heat box,
and shall provide a down-flow heating pattern.
Elements: : Assemblies shall be constructed of coiled Nickel Chromium
alloy, corrosion-resistant wire strung through a minimum of four rows of
mica insulator. Element assemblies shall have factory provided connection
to allow field modification to 50% wattage at time of installation.
Smart Limit Thermal Protection: Turns off heater during any unsafe
temperatures on inlet or outlet and will only reset if power is interrupted for
10 minutes. Simply turning thermostat down below set point will reset.
Exclusive King design and patented for US and Canada under
#6,748,163 B2 and #2,393,882
Wall Can with QuickSet™ stud alignment tabs: The wall can shall be
20 gauge electro-galvanized steel and contain knockouts through which
power leads are brought. The wall can shall be able to mount directly to wall
studs in new or existing construction. The wall can shall be provided with
QuickSet™ stud alignment tabs, used for maintaining proper depth during
new installation. The wall can shall be supplied with a factory installed ground
wire. Clearance: 6” to a side wall, 4” from floor minimum.
Grill: The grill shall be a louvered, one-piece design with rounded edges on all
four sides, with rounded corners to prevent snags from contact with other materials.
The grill shall be epoxy powder- coated in the color specified by manufacturer.
Approvals: cULus (E41422)
Factory Installed Options
MODEL UPC DESCRIPTION SHIP WEIGHT lbs
TKIT-1BW 20654 Built-in Single Pole Single Throw Thermostat Kit, Bright White 0.5
TKIT-2BW 20655 Built-in Double Pole Single Throw Thermostat Kit, Bright White 0.5
TKIT-1A 11058 Built-in Single Pole Single Throw Thermostat Kit, Almond 0.5
TKIT-2A 11059 Built-in Double Pole Single Throw Thermostat Kit, Almond 0.5
Accessories
STEP 2: Order Wall Can
MODEL UPC DESCRIPTION SHIP WEIGHT lbs
UIC 12640 Recess Wall Can 3.5
UICF 12540 Recess Can with Flange (remodel) 4
WSC 19202 Surface Can - White 13.5” L x 10” W x 4”H 4
WSC-A 19203 Surface Can - Almond 13.5” L x 10” W x 4”H 4
STEP 3: Order Grill (not required for -I models)
MODEL UPC DESCRIPTION SHIP WEIGHT lbs
WG-W 11914 Grill - White 4
WG-A 12785 Grill - Almond 4
WOG 19200 10” W x 17” H Retrofit Grill 3
WOG-A 18605 10” W x 17” H Retrofit Grill - Almond 3
WOG-XL-W 18606 14” W x 13.5” H Retrofit Grill - White 3
NOTE: This is the quickest option when the factory installed heaters options are not in stock.