Instructions / Assembly

ManualsBrandsKing Canopy ManualsStorage & OrganizationShade King 10 ft. W x 20 ft. D Silver Carport

Shade King™ 10ft X 20ft

10ft8in Wide x 20ft Deep x 5ft8in Side Height x

9ft9in Center Height

King Canopy Item #: KMK1PCS

With 6 Legs, Cover, Elastic Ball Straps & Foot Pads

WARNING:

Keep all ame and heat sources

away from this tent fabric. Meets

the ammability requirements of

CPAI-84 Section 6 and NFPA-701.

It is not re proof. The fabric will burn if

left in continuous contact with

any ame source.

Distributed by:

PIC America, LTD.

1730 Five Points Lane • Fuquay-Varina, NC 27526

1-800-800-6296 • www.kingcanopy.com

Summary of content (8 pages)

PAGE 1
Shade King™ 10ft X 20ft 10ft8in Wide x 20ft Deep x 5ft8in Side Height x 9ft9in Center Height King Canopy Item #: KMK1PCS With 6 Legs, Cover, Elastic Ball Straps & Foot Pads Distributed by: PIC America, LTD. 1730 Five Points Lane • Fuquay-Varina, NC 27526 1-800-800-6296 • www.kingcanopy.com WARNING: Keep all flame and heat sources away from this tent fabric. Meets the flammability requirements of CPAI-84 Section 6 and NFPA-701. It is not fire proof.
PAGE 2
PARTS LIST 5X8PCS 18 pc 1 3/8” diameter 68” Pipe 4X6PCS 6 pc 1 3/8” diameter 52” Swaged Pipe 3WPCS 6 pc 3-way connectors 4WPCS 3 pc 4-way connectors BALL50 50 pc Elastic ball straps T10203 1 pc Cover PFOOT 6 pc Foot pads
PAGE 3
FRAME ASSEMBLY Step 1 Place all corners and pipe on the ground as shown. The swaged pipes are used to form the length of the canopy. Step 2 Start with the center and complete the center frame first. Then assemble each side. NOTE: Attach the cover before inserting the legs.
PAGE 4
COVER ASSEMBLY Step 1 Unfold the cover with the grommets toward the cover’s bottom and place over the frame. Step 2 Begin attaching the cover with the elastic ball straps by inserting the elastic cord of the ball strap underneath the cover and through the grommet. Then pull cord taut until ball stops. Wrap the cord around the pole and under the ball. This will hide the ball under the cover and provide a more finished look to your unit.
PAGE 5
LEGS ASSEMBLY NOW, CONNECT THE LEG POLES TO THE ROOF ASSEMBLY WITH THE COVER ALREADY POSITIONED ON TOP OF THE UNIT. Step A: First insert the pipes for the middle poles into the 3- and 4-way connectors, and then connect the end leg pipes in the same way. (See illustration) Step B: Push the foot pads onto the bottom of each leg. NOTE: The foot pads are NOT for anchoring the canopy! insert second insert first IMPORTANT! Once the legs and cover are assembled, your canopy will act like a kite in the wind.
PAGE 6
ANCHORING YOUR UNIT This canopy is designed for use as a temporary structure. After assembly, the canopy MUST BE securely anchored to the ground to prevent damage from winds. Your canopy will act like a kite in the wind if not properly and securely anchored to the ground. Severe winds will cause the frame to twist and unanchored legs will fall, thereby collapsing the canopy. If severe winds are expected, you must remove the cover from the frame to prevent damage.
PAGE 7
IMPORTANT NOTICE: PLEASE READ CAREFULLY We are confident that you will be completely satisfied with your King Canopy unit. Please take a moment to read the very important information below, and call us with any questions you may have. King Canopy/PIC America, LTD. has no control over wind, snow, ice, rain or any other weather condition and we are in no way responsible for any damage caused by the canopy or to the canopy.
PAGE 8
PRODUCT INFORMATION Defective Parts We try our best to eliminate any defective parts that are shipped with our products. If, however, you should find a defective part, we will replace – free of charge – any part which is defective. You will need to provide proof of purchase showing date of purchase and provide us with detailed description of the defective component. Your replacement will be shipped by ground shipping, freight prepaid.