Installation Guide

ManualsBrandsKing Canopy ManualsKitchenGarden Party 13 ft. W x 13 ft. D Green Gazebo

Garden Party

™

13ft X 13ft

13ft Wide x 13ft Deep x 6ft3in Side Height /

10ft4in Center Height

King Canopy Item #: GP1313

With 4 Legs, Foot Pads, Cover & Screens.

WARNING:

Keep all ame and heat sources

away from this tent fabric. Meets

the ammability requirements of

CPAI-84 Section 6 and NFPA-701.

It is not re proof. The fabric will burn if

left in continuous contact with

any ame source.

Distributed by:

PIC America, LTD.

1730 Five Points Lane • Fuquay-Varina, NC 27526

1-800-800-6296 • www.kingcanopy.com

Summary of content (8 pages)

PAGE 1
Garden Party™ 13ft X 13ft 13ft Wide x 13ft Deep x 6ft3in Side Height / 10ft4in Center Height King Canopy Item #: GP1313 With 4 Legs, Foot Pads, Cover & Screens. Distributed by: PIC America, LTD. 1730 Five Points Lane • Fuquay-Varina, NC 27526 1-800-800-6296 • www.kingcanopy.com WARNING: Keep all flame and heat sources away from this tent fabric. Meets the flammability requirements of CPAI-84 Section 6 and NFPA-701. It is not fire proof.
PAGE 2
PARTS LIST 6X6PC 12 pc 78” Pipe 6X6PC 4 pc 78” Swedge pipe 2X8PC 4 pc 32” Swedge pipe 4WCPC 4 pc 4-way connectors FEET 4 pc Foot pads 2-PC 2 pc 2 piece white powder coated fitting GPT13 1 pc 100% Polyester Cover with Screens
PAGE 3
FRAME ASSEMBLY 1. Arrange all pipes and fittings on the ground as in Figure # 1. 2. Insert one swaged pipe into one long straight pipe. This extended pipe will be inserted into each of the corner fittings to form the length of the sides. Insert short swaged pipe into long pipe and then into each of the corner fittings to form roof supports. (Figure # 3) 3. To form peak, insert two of the roof pipe into the ends of one of the two-piece center fitting (Figure # 2). Repeat for the other cross peak sections.
PAGE 4
SCREEN ASSEMBLY 1. Position screens on outside of the leg poles with the elastic ties facing out (Figure #1). Screens attach to the top frame like shower curtains using the included rings. (Figure #2) Figure #1 Figure #2 2. Tie the strap around the corner fitting at the top.
PAGE 5
SCREEN ASSEMBLY 3. Attach the screens to the leg poles with the elastic ties as shown (Figure #3). Figure #3 4. Now you can either zipper the screens together or tie the screens back by securing the elastic tie strap around the screens and attaching them to the ties that are holding the screen walls at the legs.
PAGE 6
ANCHORING YOUR UNIT This canopy is designed for use as a temporary structure. After assembly, the canopy MUST BE securely anchored to the ground to prevent damage from winds. Your canopy will act like a kite in the wind if not properly and securely anchored to the ground. Severe winds will cause the frame to twist and unanchored legs will fall, thereby collapsing the canopy. If severe winds are expected, you must remove the cover from the frame to prevent damage.
PAGE 7
IMPORTANT NOTICE: PLEASE READ CAREFULLY We are confident that you will be completely satisfied with your King Canopy unit. Please take a moment to read the very important information below, and call us with any questions you may have. King Canopy/PIC America LTD., has no control over wind, snow, ice, rain or any other weather condition and we are in no way responsible for any damage caused by the canopy or to the canopy.
PAGE 8
PRODUCT INFORMATION Defective Parts We try our best to eliminate any defective parts that are shipped with our products. If, however, you should find a defective part, we will replace – free of charge – any part which is defective. You will need to provide proof of purchase showing date of purchase and provide us with detailed description of the defective component. Your replacement will be shipped by ground shipping, freight prepaid.