Instructions / Assembly

ManualsBrandsKing Canopy ManualsGazebos10 ft. x 10 ft. Garden Party Canopy with Caramel Creme Cover

Garden Party

™

10ft X 10ft

9ft 9in Wide x 9ft 9in Deep x 6ft3in Side Height /

9ft7in Center Height

King Canopy Item #: GP1010

With 4 Legs, Foot Pads, Cover & Screens.

WARNING:

Keep all ame and heat sources

away from this tent fabric. Meets

the ammability requirements of

CPAI-84 Sec 6 and NFPA 701. It is not

re proof. The fabric will burn if left in

continuous contact with any ame source.

Distributed by:

PIC America, LTD.

8009 Purfoy Road • Fuquay-Varina, NC 27526

1-800-800-6296 • www.kingcanopy.com

Summary of content (9 pages)

PAGE 1
Garden Party™ 10ft X 10ft 9ft 9in Wide x 9ft 9in Deep x 6ft3in Side Height / 9ft7in Center Height King Canopy Item #: GP1010 With 4 Legs, Foot Pads, Cover & Screens. Distributed by: PIC America, LTD. 8009 Purfoy Road • Fuquay-Varina, NC 27526 1-800-800-6296 • www.kingcanopy.com WARNING: Keep all flame and heat sources away from this tent fabric. Meets the flammability requirements of CPAI-84 Sec 6 and NFPA 701. It is not fire proof.
PAGE 2
PARTS LIST TOP4WPC GPT10SCREENS STAKE 4WCPC 3X2PC FOOTPC 6X6PC 6X6PC 12 pc 78” Pipe 1 3/8” 3X2PC 4 pc 38” Swedge Pipe 1 3/8” 4WCPC 4 pc 4-Way Fittings 1 3/8” FOOTPC 4 pc Metal Foot Pads 1 3/8” TOP4WPC 1 pc 1 Piece 4-Way Fitting 1 3/8” GPT10 1 pc 100% Polyester Cover GPT10SCREENS 4 pc Screen Walls STAKE 16 pc Nail Stakes GPT10
PAGE 3
FRAME ASSEMBLY 1. Arrange all pipes and fittings on the ground as in Figure #1 below. 2. Starting with the center peak 4-way fitting (TOP4WPC) connect all 4 pipe sections (6X6PC) that form the center peak into the center peak 4-way fitting (TOP4WPC). Figure #2 below. 3. Starting at one corner, attach a 4-way corner fitting (4WCPC) and proceed to assemble the perimeter of the canopy with the 6X6PC, 3X2PC and remaining 4WCPC fittings (see figure #3 below).
PAGE 4
LEG & SCREEN ASSEMBLY 5. Attach the 4 foot pads (FOOTPC) to each of the 4 leg pipes (6X6PC) and tighten the eye bolts to secure them. Lift one side of the canopy and insert the legs into the corner 4-way fittings (see figure #6). Repeat the step for the opposite side. Now go ahead and securely tie the straps at the corners of the cover as shown in figure #7. You are now able to use the canopy if you do not want to attach screens at this time (see figure #7).
PAGE 5
SCREEN ASSEMBLY 8. Your enclosed canopy should now look like the one in figure #12 below. To set up your canopy with the screens open you can “scallop” the screens and tie them at the corners for a more decorative look. Begin by unzipping and detaching the hook and loop strip of one side of the screen (figure #13) and proceed to “scallop” the screen in 2 - 3 inch intervals. Repeat the step for the other side of the screen until your corner looks as shown in figures #14 and 15 on next page.
PAGE 6
SCREEN ASSEMBLY Figure #15 Figure #14 Scallop the Screen. Figure #16 Figure #17 Wrap Band Around Pole and Screens and Attach.
PAGE 7
ANCHORING YOUR UNIT This canopy is designed for use as a temporary structure. After assembly, the canopy MUST BE securely anchored to the ground to prevent damage from winds. Your canopy will act like a kite in the wind if not properly and securely anchored to the ground. Severe winds will cause the frame to twist and unanchored legs will fall, thereby collapsing the canopy. If severe winds are expected, you must remove the cover from the frame to prevent damage.
PAGE 8
IMPORTANT NOTICE: PLEASE READ CAREFULLY We are confident that you will be completely satisfied with your King Canopy unit. Please take a moment to read the very important information below, and call us with any questions you may have. King Canopy/PIC America, LTD. has no control over wind, snow, ice, rain or any other weather condition and we are in no way responsible for any damage caused by the canopy or to the canopy.
PAGE 9
PRODUCT INFORMATION Defective Parts We try our best to eliminate any defective parts that are shipped with our products. If, however, you should find a defective part, we will replace – free of charge – any part which is defective. You will need to provide proof of purchase showing date of purchase and provide us with detailed description of the defective component. Your replacement will be shipped by ground shipping, freight prepaid.