Replacement Part List

ManualsBrandsKing Canopy ManualsCanopies20 ft. x 20 ft. Event Tent with White Cover

Event Tent

™

20ft x 20ft

20ft Wide x 20ft Deep x 6ft 9in Side Height /

12ft 4in Center Height

King Canopy Item #: ET2020G

With 8 Legs, Green & White PE Cover,

Elastic Ball Straps & Foot Pads.

WARNING:

Keep all ame and heat sources

away from this tent fabric. Meets

the ammability requirements of

CPAI-84. It is not re proof. The fabric

will burn if left in continuous contact

with any ame source.

Distributed by:

PIC America, LTD.

1730 Five Points Lane • Fuquay-Varina, NC 27526

1-800-800-6296 • www.kingcanopy.com

Summary of content (8 pages)

PAGE 1
Event Tent™ 20ft x 20ft 20ft Wide x 20ft Deep x 6ft 9in Side Height / 12ft 4in Center Height King Canopy Item #: ET2020G With 8 Legs, Green & White PE Cover, Elastic Ball Straps & Foot Pads. Distributed by: PIC America, LTD. 1730 Five Points Lane • Fuquay-Varina, NC 27526 1-800-800-6296 • www.kingcanopy.com WARNING: Keep all flame and heat sources away from this tent fabric. Meets the flammability requirements of CPAI-84. It is not fire proof.
PAGE 2
PARTS LIST 6X6-2PC 16 pc 77.5” x 2” Pipe 6X6-15PC 9 pc 77.
PAGE 3
FRAME ASSEMBLY Step 1 Separate all pieces according to size and shape and arrange per the illustration shown below. Please note: • The 8 - 50” x 2” and 8 - 77.5” x 2” pipes are used to form the roof rafters • The 9 - 11/2” x 77.5” pipes are used to form the sides & peak 77.5’’ 77.5’’ 50’’ 77.5’’ 50’’ 77.5’’ 77.5’’ 50’’ 50’’ 77.5’’ 77.5’’ 77.5’’ 77.5’’ 77.5’’ 50’’ 77.5’’ 77.5’’ 77.5’’ 77.5’’ 50’’ 50’’ 50’’ 77.5’’ 77.5’’ 77.5 in Set aside eight 77.5in x 2in pipes to use for legs. 77.
PAGE 4
COVER ASSEMBLY Step 1 Unfold the cover with the grommets toward the cover’s bottom and place over the frame. The flared edges should be located at each of the 4 corners of the frame. Step 2 Begin attaching the cover with the elastic ball straps by inserting the elastic cord of the ball strap underneath the cover and through the grommet. Then pull cord taut until ball stops. Wrap the cord around the pole and under the ball.
PAGE 5
LEGS ASSEMBLY NOW, CONNECT THE LEG POLES TO THE ROOF ASSEMBLY WITH THE COVER ALREADY POSITIONED ON TOP OF THE UNIT. Insert Second Insert First Step A: First insert the pipes for the middle poles into the 3- and 4-way connectors, and then connect the end leg pipes in the same way. (See illustration) Step B: Push the eight foot pads onto the bottom of each leg. NOTE: the foot pads are NOT for anchoring the canopy! Step C: Attach the leg skirts to the foot pads. Your Event Tent has leg skirts for each leg.
PAGE 6
ANCHORING YOUR UNIT This canopy is designed for use as a temporary structure. After assembly, the canopy MUST BE securely anchored to the ground to prevent damage from winds. Your canopy will act like a kite in the wind if not properly and securely anchored to the ground. Severe winds will cause the frame to twist and unanchored legs will fall, thereby collapsing the canopy. If severe winds are expected, you must remove the cover from the frame to prevent damage.
PAGE 7
IMPORTANT NOTICE: PLEASE READ CAREFULLY We are confident that you will be completely satisfied with your King Canopy unit. Please take a moment to read the very important information below, and call us with any questions you may have. King Canopy/PIC America, LTD. has no control over wind, snow, ice, rain or any other weather condition and we are in no way responsible for any damage caused by the canopy or to the canopy.
PAGE 8
PRODUCT INFORMATION Defective Parts We try our best to eliminate any defective parts that are shipped with our products. If, however, you should find a defective part, we will replace – free of charge – any part which is defective. You will need to provide proof of purchase showing date of purchase and provide us with detailed description of the defective component. Your replacement will be shipped by ground shipping, freight prepaid.