Instructions / Assembly

ManualsBrandsKing Canopy ManualsCar CanopiesUniversal 10 ft. x 13 ft. x 10 ft. White Roof Steel Carport

10’X13’ UNIVERSAL 6 LEG

ITEM #: C61013PC

Dimensions:

10ft. 8in. Wide x 13ft. Deep x 6ft. 8in. Side Height / 9ft. 9in. Center Height

WARNING:

Keep all ame and heat sources

away from this tent fabric. Meets

the ammability requirements of

CPAI-84 It is not re proof

The fabric will burn if left in

continuous contact with any

ame source.

Distributed by: PIC America, LTD.

1730 Five Points Lane • Fuquay-Varina, NC 27526

1-800-800-6296 • www.kingcanopy.com

Summary of content (9 pages)

PAGE 1
0’X13’ UNIVERSAL 6 LEG ITEM #: C61013PC Dimensions: 10ft. 8in. Wide x 13ft. Deep x 6ft. 8in. Side Height / 9ft. 9in. Center Height WARNING: Keep all flame and heat sources away from this tent fabric. Meets the flammability requirements of CPAI-84 It is not fire proof The fabric will burn if left in continuous contact with any flame source. Distributed by: PIC America, LTD. 1730 Five Points Lane • Fuquay-Varina, NC 27526 1-800-800-6296 • www.kingcanopy.
PAGE 2
PARTS 4WPC TDS1013 BALLW 5X8PC CCLIP 6X6PC 5X8PC 3WPC 4WPC BALL50W PFOOT TDS1013 CCLIP PFOOT 12 pc 6 pc 6 pc 3 pc 50 pc 6 pc 1 pc 4 pc 3WPC 6X6PC 78” Powder Coated Pipe 68” Powder Coated Pipe 3-way Connectors 4-way Connectors Elastic Ball Straps Plastic Foot Pads White Drawstring Cover Curtain Clips
PAGE 3
FRAME ASSEMBLY 3WPC 6X6PC 6X6PC 4WPC 6X6PC 3WPC 5X8PC 5X8PC 5X8PC 5X8PC 6X6PC 3WPC 3WPC 4WPC 6X6PC 4WPC 6X6PC 5X8PC 6X6PC 6X6PC 3WPC 5X8PC 6X6PC 6X6PC 3WPC 1) Start by laying out all of the parts and pieces to your King Canopy. Please refer to the parts list to ensure that your kit is complete. When all the parts have been accounted for, begin to layout the perimeter of your frame according to the photo above (6X6PC & 5X8PC).
PAGE 4
Le n gt h FRAME & ATTACHING COVER Width 4) Once one side is complete, move to opposite sides of the unassembled frame lifting the frame and connecting the remaining 5X8PC pipe. Continue previous steps until all pipe and fittings are connected. 5) Now that the roof frame work is complete you can begin to attach the drawstring style cover. Start by laying out the cover to determine which way it is folded the length or width or the frame.
PAGE 5
ATTACHING COVER 8) Wrap the cord around the pole and secure around the ball. 9) Be sure all four corners are attached before attaching the remaining ball straps. 10) Continue attaching straps from left to right in a zig zag pattern starting at the two center peaks. 11) Next continue attaching the straps down each side and end. Make sure the cover stays centered on the frame.
PAGE 6
LEG ASSEMBLY 12) Now that all the ball straps are attached. Insert the pipe into each plastic foot pad and begin to attach the legs to the frame. Place each leg next to the three and four way fittings. 13) Slide a c-clip on to each corner leg before inserting them into the 3-way fittings. Insert First Insert Second Insert First 14) Starting with the two outside legs grab the base of the 3-way corner fitting. Lift the frame and insert the leg into the open 3-Way fitting. Next insert the center leg.
PAGE 7
COVER ADJUSTMENT Pull Cord Down & Hook 16) Pull each drawstring cord down evenly and hook onto the c-clip at each corner leg. Repeat step at the other end of the canopy. Use remaining ball straps to secure the valances to the 17) Use the remaining ball straps to secure the valances to the legs. This canopy is designed for use as a temporary structure. After assembly, the canopy MUST BE securely anchored to the ground to prevent damage from winds.
PAGE 8
IMPORTANT NOTICE: PLEASE READ CAREFULLY We are confident that you will be completely satisfied with your King Canopy unit. Please take a moment to read the very important information below, and call us with any questions you may have. King Canopy/PIC America, LTD. has no control over wind, snow, ice, rain or any other weather condition and we are in no way responsible for any damage caused by the canopy or to the canopy.
PAGE 9
WARRANTY INFORMATION Defective Parts We try our best to eliminate any defective parts that are shipped with our products. If, however, you should find a defective part, we will replace – free of charge – any part which is defective. You will need to provide proof of purchase showing date of purchase and provide us with detailed description of the defective component. Your replacement will be shipped by ground shipping, freight prepaid.