User Manual Fully Automatic Blood Pressure Monitor Arm Type TMB-1970 Thank you so much for selecting the Kinetik Wellbeing Fully Automatic Blood Pressure Monitor Guangdong Transtek Medical Electronics Co., Ltd. Zone A, No.
TABLE OF CONTENTS SUPPORT.............................................................................................................................2 INTRODUCTION...................................................................................................................3 General Description Indications for Use Contraindications Measurement Principle Safety Information LCD Display Signal Monitor Components List BEFORE YOU START........................................................................
INTRODUCTION SUPPORT Support Our manual should provide you with all the information you need to set up and use this product. If you have a question, have a look at our Troubleshooting page! For further assistance, why not contact our Customer Care team directly? We’re here to help! Our Customer Care team are available from 9am-5pm, Monday to Friday (excluding bank holidays). We promise to respond to all queries and will ensure to resolve any issue you may be having.
INTRODUCTION INTRODUCTION CAUTION Safety Information The signs below might be in the user manual, labeling or other component. They are the requirement of standard and using. Symbol for “THE OPERATION GUIDE MUST BE READ” Symbol for “SERIAL NUMBER” Symbol for “ENVIRONMENT PROTECTION - Electrical waste products should not be disposed of with household waste. Please recycle where facilities exist.
INTRODUCTION CAUTION * When measurement, please avoid compression or restriction of the connection tubing. * The device cannot be used with HF surgical equipment at the same time. * The ACCOMPANYING DOCUMENT shall disclose that the SPHYGMOMANOMETER was clinically investigated according to the requirements of ISO 81060-2:2013. * To verify the calibration of the AUTOMATED SPHYGMOMANOMETER, please contact the manufacturer.
INTRODUCTION INTRODUCTION LCD display signal Monitor Components CUFF AIR HOSE AIR CONNECTOR PLUG LCD DISPLAY START/STOP BUTTON SET BUTTON MEM BUTTON SYMBOL DESCRIPTION High blood pressure Diastolic blood pressure Low blood pressure Pulse display Pulse in beats per minute Deflation symbol The cuff is deflating. Memory Indicate it is in the memory mode and which group of memory it is.
BEFORE YOU START BEFORE YOU START Installing and Replacing the Batteries • Open the battery cover. • Install the batteries as indicated in the battery compartment. (Always select the authorised / specified battery: Four AAA-size batteries). • Replace the battery cover. Setting the Date and Time It is important to set the date and time before using your blood pressure monitor for the first time, so that a correct time stamp can be assigned to each record that is stored in the memory.
BEFORE YOU START BEFORE YOU START 4 . After confirming the minute, the LCD will display “do nE” and the monitor will shut off after several seconds. Month Day About user ID 12 Time format Time format Hour Minute There is only one user ID available. The user has 90 memory spaces, and is designed for 1 person to save measured values.
MEASUREMENT MEASUREMENT Start the Measurement Tie the Cuff 1. Remove all jewelry, such as watches and bracelets from your left arm.Note: If your doctor has diagnosed you with poor circulation in your left arm, use your right arm. 1. When the monitor is off, press the “START/STOP” button, the LCD display will show shortly. 2. Roll or push up your sleeve to expose the skin. Make sure your sleeve is not too tight. 2. Remain still and do not talk until the full measurement is complete. LCD display 3.
DATA MANAGEMENT DATA MANAGEMENT Recall the Records Delete the Records If you did not get the correct measurement, you can delete one record or all records by following steps below. 1. When the monitor is off, press the “MEM” button, the lastest record will display. Delete one record: 1. Press the “MEM” button to enter the memory mode, then press the “MEM” or “SET” buton to find the record you want to delete.
DATA MANAGEMENT INFORMATION FOR USER Delete all records: 1. Press the 'MEM' button to enter the memory mode, then press and hold the 'SET' button. The LCD will display and flash 'dEL ALL'. Tips for Measurement Measurements may be inaccurate if taken in the following circumstances. 2. Press the 'SET' or 'MEM' button to toggle between deleting all readings (dEL ALL) or not (dEL no).
INFORMATION FOR USER ABOUT BLOOD PRESSURE Maintenance What are systolic pressure and diastolic pressure? In order to get the best performance, please follow the instructions below. When ventricles contract and pump blood out of the heart, the blood pressure reaches its maximum value in the cycle, which is called systolic pressure. When the ventricles relax, the blood pressure reaches its minimum value in the cycle, which is called diastolic pressure.
ABOUT BLOOD PRESSURE TROUBLESHOOTING Why does my blood pressure fluctuate throughout the day? 1. Individual blood pressure varies multiple times everyday. It is also affected by the way you tie your cuff and your measurement position, so please take the measurement under the same conditions. 2.If the person takes medicine, the pressure will vary more. 3.Wait at least 3 minutes for another measurement.
CONTACT INFORMATION SPECIFICATIONS Contact Information Power supply Battery powered mode: 6V DC 4x AAA batteries Display mode Measurement mode Digital LCD display V.A.
EMC GUIDANCE EMC GUIDANCE EMC Guidance Table 2 The ME EQUIPMENT or ME SYSTEM is suitable for home healthcare environments. Warning: Don’t be near the active HF surgical equipment and the RF shielded room of an ME system for magnetic resonance imaging, where the intensity of EM disturbances is high. Warning: Use of this equipment adjacent to or stacked with other equipment should be avoided because it could result in improper operation.
EMC GUIDANCE Table 3 Guidance and manufacturer’s declaration - electromagnetic Immunity Radiated RF Test Band Service Modulation Modulation IEC61000-4-3 Frequency (MHz) (W) (Test (MHz) specifications 1.8 for 385 380-390 TETRA Pulse ENCLOSURE 400 modulation b) PORT 18Hz IMMUNITY to GMRS 460，FM c) ± 5kHz RF wireless 2 deviation 1kHz 450 430-470 FRS 460 communicasine ti-ons 710 704-787 LTE Band Pulse equipment) 0.
