Datasheet
83
installation
SIGNAL MANAGEMENT
Subject to technical alterations, as well as to changes of the design and the colour
Video / Audio signal amplifi ers / splitters
Illustration Item Description Ref. No.
AV splitter Pro 1 : 3 Signal splitter for composite video and stereo Audio 7481000001
1 input / 3 outputs
(3 x 3 cinch f)
Bandwidth video 430 MHz,
audio 100 kHz @ -3dB
Adjustable audio level,
video level and cable EQ
Metal casing 165 x 120 x 45 mm
Power supply DC 12 V
, 50 mA
Video / Audio switchers
Illustration Item Description Ref. No.
AV Share Basic 4 : 1 Selector for composite video, S-video and stereo audio as well as video converter 7481000000
4 inputs / 1 output
(4-pin MiniDIN, 3 x cinch, all f)
S-video – composite video conver
ter
Composite video – S-video converter
Plastic casing 190 x 115 x 50 mm
A
V selector Basic 6 : 1 -
remote
Selector for S-video, compositive video (FBAS) and stereo Audio with remote control 7481000007
6 inputs / 1 output
(S-video 4-pin MiniDIN, 3 cinch)
Plastic casing
Integrated power supply
Incl. IR remote control
TV tuner / progressive scan converter
Illustration Item Description Ref. No.
TV tuner/progressive scan
converter TVW 7
Converts a projector or a TFT display into a TV and video and S-video into high-resolution graphic signals.
Can be used as TV tuner with video text, progressive scan converter and scaler as well as signal switcher.
7486000003
3D motion adaptive de-interlacer
Picture in picture (video in PC image)
For P
AL, SECAM, NTSC signals
OSD menu
Inputs: antenna (analogue terrestic/ cable),
AV input (3 x cinch), S-video (4-pin MiniDIN),
VGA (HD 15), 1 x Audio jack
Incl. remote control, stand, VGA cable, audio cable,
power supply
Dimensions: 160 x 115 x 26 mm
Outputs: VGA (HD 15), 2x audio jack (Line/head
phone)
Output signal: 1024 x 768, 1280 x1024, 1280 x
768, 1440 x 900 pixels
Accessories
Illustration Item Description Ref. No.
ECOMAN Beamer Separates the projector from the mains after ca. 5 minutes of operation in standby mode.
The integrated IR receiver switches the projector back to standby when it gets an IR signal. If the signal is
not meant for the projector, the unit will be switched off again.
7487000000
Time controlled mains separation of projectors
(after ca. 5 min. in standby mode)
High voltage protection
Maximum power 460 W
Power consumption < 1 W
230 V AC / 50 Hz
Output Schuko plug
KINDERMANN
SwitchBox Plus
The SwitchBox Plus in combination with a simple low current switch resp. a potential free contact allows to
safely connect and operate several 230 V devices via a thin bell wire.
7487000001
Schuko plug
Safety class: IP20, only for dr
y rooms
Green status LEDs
LOAD CIRCUIT
Voltage: 230 V~, 50 Hz
Maximum power: 2000 W (8.7 A) / all loads
together
CONTROL CIRCUIT
Connection: 2-pin, 5.08 mm
Standard confi guration: contacts closed (< 2000
Ohm) --> 230 V load switched on contacts open
--> 230 V load switched off
IR-Link Extends the range of IR remote controls. Extension cable for IR signals sent by remote controls, consisting of: 5822000005
IR receiver
Connector block with power supply 12 V DC
IR emitter with 2 IR diodes
Cable IR receiver - connector block ca. 2 m*
Cable connector block - IR ermitter ca. 3 m
*Extension possible with 3-pin cable 5698000011
(see page 85)
Multiple socket with RS
232 control
5-fold multiple socket, the single sockets can be switched on and of
f via RS 232 command. 7487000002
Interface: 9-pin SubD
Max. 1000 W / socket
Max. 2500 W overall load