Use and Care Manual

!
Depending on the surface texture, porosity and application method. Does not include the loss of
material from spraying.
!!
At 77°F (25°C), 50% RH. Longer dry time may be required in cooler temperatures and in
higher humidity.
SURFACE PREPARATION (The following steps are recommended for product
performance)
• The surface must be clean, free of dust, grease, wax, peeling paint, mold,
mildew and wallpaper paste.
• If washing is necessary, use a non-soapy detergent or a TSP substitute. Rinse
well and allow to dry.
• Peeling or Checked Paint: Scrape off loose paint and sand to a smooth surface.
Sanding or removal of paint containing lead is hazardous.*
•
†
Glossy Surfaces: For maximum adhesion, scuff sand the surface thoroughly
before priming.*
• Mold or Mildew Covered Surfaces: Any existing mold and/or mildew on the
surface MUST be removed before priming or painting. Wash the area with a
mildew remover, rinse with water and allow to dry before priming.
*
WARNING If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC.
Contact the National Lead Information Center at 1-800-424-LEAD or log on to www.epa.gov/lead.
Mineral Spirits
Clean-Up
20 – 25 sq. ft. (1.9 – 2.3 m
2
)
per container.
†
30 Min - Dry Time to Touch
!!
1 Hr - Dry Time to Recoat
!!
Protect from
Freezing
KILZ
®
MOLD & MILDEW INTERIOR/EXTERIOR AEROSOL PRIMER
WHERE TO USE
KILZ
®
MOLD & MILDEW
†
Primer is a primer-sealer-stainblocker that is specially
designed for residential surfaces in high humidity, moisture and temperature
environments such as kitchens, bathrooms, powder rooms and laundry rooms. This
convenient aerosol is ideal for small paint projects, spot priming and touch-ups for
these spaces. It offers excellent adhesion to both interior and exterior surfaces and
provides a sound anchor for paints. The EPA registered active ingredient creates
a mold and mildew-resistant lm that protects the primer from mold and mildew
growth. KILZ MOLD & MILDEW Primer will block most medium to heavy stains
including felt marker, grease, ink, pencil, tannin and water stains. It is a fast drying,
and cleans-up with mineral spirits. Not recommended for oors.
WARNING
Cancer and Reproductive Harm
www.P65Warnings.ca.gov
KEEP OUT OF REACH OF CHILDREN – DO NOT TAKE INTERNALLY
LIFETIME LIMITED WARRANTY: Masterchem Industries LLC warrants to you, the original residential consumer purchaser, the
performance of this product as described on this label for so long as you reside in your home. If this product is found to be defective upon
inspection by its representative, Masterchem Industries LLC will, at its option and upon presentation of proof-of-purchase (the original receipt),
either furnish an equivalent amount of new product or refund the original purchase price of this product to you. This warranty is not transferable.
This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental or
consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal
theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you. To the extent permitted by applicable law, any implied warranties including the implied warranties of merchantability and of
tness for a particular purpose, are limited to the duration of this express warranty. Some states do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you. This warranty gives you specic legal rights and you may also have other rights,
which vary from state to state. Note to residents of the State of New Jersey: The provisions of this warranty, including its limitations,
are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. For warranty service, call: 1-866-774-6371, or
email: [e-mail]. Masterchem Industries LLC reserves the right to inspect any and all application of the product prior to
processing your claim made under this warranty.
©2020 Masterchem Industries LLC
1-866-774-6371 • www.kilz.com
L204647 / L204648 • REV. 08/20
Max VOC (by weight): 60% Max Product Weighted
MIR: 0.7
• Convenient for spot priming, touch-ups and
small projects
• Mold & Mildew Resistant Primer Film
• Contains an EPA-registered mildewcide
• Prevents mold and mildew growth on the primer lm
• Ideal for spaces prone to high moisture and humidity
• Seals porous surfaces
• Excellent adhesion
• Blocks most light to medium stains
• Clean-up with mineral spirits
• Fast drying, Paint over in 1 hour
APPLICATION
• Eye protection is recommended.
• For best results, use at room temperature.
• Cover adjacent areas to protect from overspray.
• Shake can vigorously for 1 minute after mixing ball begins to rattle and often
during use.
• Hold can upright, moving from side-to-side while spraying lightly and evenly
about 12" from area being painted.
• 2 – 3 thin coats produce best results.
• Topcoat with water-based or oil-based paint after 60 minutes.
• NOTE: On some surfaces, spot priming may cause a non-uniform appearance in
the final coat. To avoid this, prime the entire surface.
• Dry Time: @ 77°F (25°C), 50% RH Longer dry time may be required in cooler
temperatures and in higher humidity. To Touch: 15 – 30 minutes
To Recoat: 1 Hour.
CLEAN-UP & DISPOSAL
• Clear spray valve immediately after use by turning can upside down and
spraying until only clear gas is released.
• If spray nozzle becomes clogged, remove and clean. Do not stick pins or wire
into can opening.
• Replace nozzle with valve opening pointed away from you.
• Clean fresh overspray with mineral spirits or paint thinner. Remove dried paint
with paint remover, but test small area first to ensure paint remover does not
damage substrate.
• Please consider donating any unused product.
• For recycling or disposal information, contact your local household refuse
collection service.
VENTILATION REQUIRED: To avoid inhalation and combustion hazards (see below), DO NOT use
this product unless you can achieve cross-ventilation by opening windows and doors during application and
drying. CONTAINS PETROLEUM DISTILLATES and ACETONE. VAPOR HARMFUL. May
affect the brain or nervous system causing dizziness, headache or nausea. Do not breathe vapors or spray
mist. If you experience eye watering, headaches or dizziness, increase fresh air, wear respiratory protection
(NIOSH / MSHA TC 23C or equivalent) or leave the area. NOTICE: Reports have associated repeated and
prolonged occupational overexposure to solvents with permanent brain and nervous system damage. Intentional
misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. Vapors May Ignite
Explosively. Do not spray near sparks, heat or open ame. Do not smoke. Vapors are heavier than air, and can
travel at oor level to distant ignition sources. Extinguish all ames and pilot lights and turn off stoves, heaters,
electric motors, high intensity lights and other sources of ignition during use and until all vapors are gone.
WARNING-CONTENTS UNDER PRESSURE. Do not puncture, incinerate (burn) or store above 120°F
(40°C). Exposure to heat or prolonged exposure to sun may cause bursting. Do not discard in home trash
compactor. FIRST AID: If you have difculty breathing, leave area to obtain fresh air. If difculty continues,
get medical attention immediately. In case of eye contact, ush immediately with plenty of water for at least 15
minutes and get medical attention. For skin contact, wash thoroughly with soap and water.