Komfort aus Tradition Directions for use kiddy maxi pro Stand 04/2006 ENG
ENG Contents Introduction 1. Applicability.................................................................. 3 2. General safety instructions......................................... 3. 3.1 3.2 General use................................................................ 6 Functions of the carrying frame.................................. 6 Functions of the sun canopy ...................................... 7 4. 4.1 4.2 Fitting into the vehicle.................................................
ENG Introduction The kiddy maxi pro is part our company's new pro line, which offers completely safety to protect your baby and growing child by means of a special material that derives energy. In order to secure your baby completely in the kiddy maxi pro seat, this is fitted in the head support area with the new material. The impact of a side collision will be absorbed particularly well before it reaches the sensitive head area of the baby.
ENG 2. General safety instructions Read through the directions for use carefully before fitting the kiddy maxi pro seat for the first time. Incorrect use can be life-threatening for your child. Many injuries are caused by carelessness and are easily avoidable. It is forbidden to make any changes whatsoever to the child restraint systems. The protective effect can be lost or restricted. If you experience difficulties please contact your specialist dealer or the manufacturer directly.
ENG Only use the seat pan for the weight category specified - up to a maximum of 13kg. Cf. chapter 1. Never use the seat pan without the original cover. It is part of the safety concept. Never use the seat pan as a shopping aid or other carrying aid. Never leave your baby unattended in the seat pan, especially not when you put the seat pan on raised surfaces (baby changing unit, table etc.). Do not place any heavy objects on the rear shelf. This could be dangerous in the event of an accident.
ENG 3. General use Please read these directions carefully before using the seat shell kiddy maxi pro for the first time. Always keep the directions for use in the box provided underneath the seat pan. This way it is always there if you encounter problems. 3.1 Functions of the carrying frame The carrying frame of your seat shell kiddy maxi pro can be locked in place in 4 places. Fig.1 Fig.2 Setting of carry handle for operation in the vehicle. Position the handle folded upwards to carry the seat pan.
ENG To adjust the carrying frame, press the yellow button on both sides on the swivel joint. Fig.5 Make sure you never position the seat shell on sloping ground and avoid putting it down on raised items (table, baby changing unit, etc.) 3.2 Functions of the sun canopy The sun canopy can be opened to protect against direct sunlight. Turn the sun canopy frame forwards until it locks in place (fig. 6). If the sun canopy is not needed, it can be fixed using the spring mounted clamp under the pan rim (fig. 7).
ENG 2. Swivel the sun canopy (fig. 8/no. 1) downwards over the top end rim of the pan. Now you can pull the clamp bracing (fig.8/no.2) down vertically and remove the clamp. (CAUTION: The clamp can only be loosened in the pan position specified. Fig.7 3. Feed the clamp out of the material strap of the sun canopy. To assemble the sun canopy proceed in reverse order. When mounting make sure that the slot in the clamp (fig. 7/no. 1) is pointing downwards. Fig.8 4. Fitting into the vehicle 4.
ENG The seat pan is not suitable for seats which are only fitted with a 2-point lap belt. Only use the seat pan on seats that have a 3-point vehicle belt. We recommend using the seat pan on the rear bench seat in cars. In vans the seat pan should be mounted on the seat that has the easiest access in the event of a rescue operation. 4.
ENG Guide the shoulder belt of the vehicle’s own 3-point belt systems on the back of the baby seat pan and thread this between the blue belt guide and the guide on the seat pan (fig. 11). Fig.11 Tighten the vehicle's own 3-point belt by heftily pulling on the shoulder belt (fig. 12). Fig.12 Some vehicles have so-called retractor locks. The automatic roll-up of the vehicle’s own belt system can be disabled. A more permanent fitting of the seat pan is possible.
ENG 5.1.1 Loosening of the 5-point belt system Before you can adapt the belt system, you must loosen this. By pressing the central belt adjustment, the area marked in red (press) in front on the cover of the seat pan and at the same time pulling on both shoulder belts you can loosen the 5-point belt system (fig. 13) Fig.13 5.1.2 Adjustment of the 5-point belt system Fig.
ENG Lock the head support adjustment in place again. The head support must be set so that the shoulder belt is at shoulder height of the baby or slightly above (fig. 15/no. 1). Fig.15 correct incorrect, too high incorrect, too low Make sure that the belts are never twisted. 5.2 Buckling up the baby Please make sure that your baby is always wearing a seat belt in the seat pan. That also means outside of the vehicle. Loosen the shoulder belt as described in section 5.1.1.
ENG Fig.18 Fig.19 The buckle is locked in place once you hear a clicking noise. (Fig.18/no.3) Check that this is fastened securely by pulling on both shoulder belts and the buckle at the same time. To tighten the shoulder belt pull in front of the central belt adjustment until the belt system fits tightly. (Fig.19/no.4) To take your baby out open the 5-point belt system by pressing the red button on the front of the buckle and loosen the belt (see chapter 5.1.1).
ENG 6.2 Cleaning the plastic parts The plastic parts can be cleaned with a mild cleaning agent or a damp cloth. Do not use harsh cleaning products (e.g. solvent). 6.3 Cleaning the 5-point belt system The belt system can be cleaned with a damp cloth. Please never wash in a washing machine and never treat with chemical cleaning agents. Make sure that the buckle stays clean so that it keeps its effectiveness.
ENG 6.4.2 Dismantling of shoulder belt Open the buckle. Weave the lap belt from the side belt tongues underneath the inner cover (fig. 21/22). Fig.21 Weave the belt through both slots on the seat pan as well as through the slot in the cover. (Fig. 22). Fig.22 Remove both buckle tongues from the belt (fig.23) Fig.23 Pull both belt straps through the inside cover, through the head part and rear panel. Feed the belt on the back of the seat pan from the tie loop with the central belt adjustment (fig. 24).
ENG 6.5 Fitting the belts When mounting the belt proceed in the reverse order of dismantling. Caution! Check the correct belt fitting. 6.6 Removing the cover In order to remove the covers of the kiddy maxi pro seat pan for cleaning, do the following: - Remove the clips of the seat pan cover from the outer rim of the plastic pan and detach the cover in the lower area from the seat pan. - Feed the buckle through the seat pan cover (item 6.4.1). - Remove the shoulder belt and proceed as described in item 6.
ENG 6.7 Replacing the cover When replacing the cover proceed in the reverse order of removing the cover. Make sure that when feeding the belt straps in the lower area of the seat pan, these are fed first through the outer slot and then through the inner slot. The belt strap must be inside the seat pan and fastened with the belt tongue (fig.21/no.1). 7.
ENG Sicartex Autozubehör Curt Würstl GmbH Schaumbergstr. 8 D-95032 Hof / Saale Tel.: 0049 (0)9281 / 7080-0 Fax: 0049 (0)9281 / 7080-21 eMail: info@kiddy.de www.kiddy.
