2527-7201-00(820-1387A):_ 2008.5.12 9:35 AM Carbon Monoxide Alarm User’s Guide Model: KN-COPF-i • 120V AC Wire-In • Rechargeable Battery Backup • Digital Display • Interconnectable with other Kidde alarms ATTENTION: Please take a few minutes to thoroughly read this user’s guide, which should be saved for future reference and passed on to any subsequent owner. Manual P/N 820-1387 Rev.
527-7201-00(820-1387A):_ 2008.5.12 9:35 AM What to do When the Alarm Sounds! Carbon Monoxide Alarm Procedure WARNING: Activation of the CO Alarm indicates the presence of Carbon Monoxide (CO) which can kill you. 1) Operate the Test/Reset button; 2) Call your emergency services (Fire Department or 911); PHONE NUMBER: 3) Immediately move to fresh air - outdoors or by an open door/window. Do a head count to check that all persons are accounted for.
2527-7201-00(820-1387A):_ 2008.5.12 9:35 AM Welcome Note: Many times throughout this User’s Guide, we will refer to Carbon Monoxide as “CO”. This Kidde carbon monoxide (CO) alarm is an important part of your family’s home safety plan. This alarm has been designed and tested to detect CO buildup in a residential environment. Your alarm is for use specifically in the home. As an owner of a CO alarm, there are some basic facts you should know about for your protection.
2527-7201-00(820-1387A):_ 2008.5.12 9:35 AM Important Warning Statements WARNING: This product is intended for use in ordinary indoor locations of family living units. It is not designed to measure compliance with Occupational Safety and Health Administration (OSHA), commercial or industrial standards. It is not suitable for installation in hazardous locations as defined in the National Electric Code.
2527-7201-00(820-1387A):_ 2008.5.12 9:35 AM 1. Information About Carbon Monoxide General Carbon Monoxide Information Carbon monoxide is a colorless, odorless and tasteless poison gas that can be fatal when inhaled. CO inhibits the blood’s capacity to carry oxygen. Periodically review this alarm manual and discuss your CO alarm emergency procedure with all the members of your family. Never ignore a CO alarm. A true alarm is an indication of potentially dangerous levels of CO.
2527-7201-00(820-1387A):_ 2008.5.12 9:35 AM 1. Information About Carbon Monoxide Carbon Monoxide PPM Levels This model is equipped with a digital display that shows levels of CO (displayed in PPM – parts per million). Learn the difference between dangerous, high, mid and low levels. Dangerous Levels: When someone is experiencing symptoms of CO poisoning and CO readings are generally above 100 PPM. Anytime someone is experiencing the symptoms of CO poisoning this should be treated as an emergency.
2527-7201-00(820-1387A):_ 2008.5.12 9:35 AM 1. Information About Carbon Monoxide exchangers. • Vehicles and other combustion engines running in an open or closed garage, attached or near a home. • Burning charcoal or fuel in grills and hibachis in an enclosed area.
2527-7201-00(820-1387A):_ 2008.5.12 9:35 AM 1. Information About Carbon Monoxide to low levels may cause symptoms, as well as short-term exposures to high levels. This Kidde unit has a time-weighted alarm – the higher the level of CO present, the sooner the alarm will be triggered. This CO alarm can only warn you of the presence of CO. It does not prevent CO from occurring, nor can it solve an existing CO problem.
2527-7201-00(820-1387A):_ 2008.5.12 9:35 AM 2. Product Features and Specifications Model KN-COPF-i Digital Display Red LED Green LED Amber LED Test/Reset Button Peak Level Button Alarm Sounder IMPORTANT: Seven (7) years after the initial power up, this alarm will “beep” every 30 seconds and display "End" to indicate that it is time to replace the alarm. Replace the alarm immediately! It will not detect CO in this condition.
2527-7201-00(820-1387A):_ 2008.5.12 9:35 AM 2. Product Features and Specifications Temperature: Operating Range: 40°F (4.4°C) to 100°F (37.8°C) Humidity: Operating range: 10-95% non-condensing Audible Alarm: 85+ dB at 10’ @ 3.4±0.
2527-7201-00(820-1387A):_ 2008.5.12 9:35 AM 3. Installation Locations Recommended Installation Locations CO alarms should be mounted in or near bedrooms and living areas. It is recommended that you install a Kidde CO alarm on each level of your home. When choosing your installation locations, make sure you can hear the Recommended Locations alarm from all sleeping areas. If you install only one CO alarm in your home, install it near bedrooms, not in the basement or furnace room.
2527-7201-00(820-1387A):_ 2008.5.12 9:35 AM 3. Installation Locations • Do not obstruct the vents located on the alarm. Do not place the alarm where drapes, furniture or other objects block the flow of air to the vents. 4. Installation Instructions Interconnecting CAUTION: Kidde (Fyrnetics/Lifesaver/Kidde/Nighthawk/Pyrene) alarms and accessories can only be interconnected with other Kidde alarms and accessories.
2527-7201-00(820-1387A):_ 2008.5.12 9:35 AM 4. Installation Instructions • With 18 alarms interconnected, it is still possible to interconnect up to a total of six remote signaling devices and/or relay modules. • The maximum wire run distance between the first and last unit in an interconnected system is 1000’ (305 m). • Make certain alarms are wired to a continuous, (non-switched) power line.
2527-7201-00(820-1387A):_ 2008.5.12 9:35 AM 4. Installation Instructions Mounting • After selecting the proper location for your CO alarm and wiring the AC QuickConnector harness, plug the AC QuickConnector into the mating connector in the back of the alarm. Be sure the connectors snap together securely. • Push the excess wire back into the electrical box. • Install the alarm in the electrical box using the four screws provided. • Turn on the AC power.
2527-7201-00(820-1387A):_ 2008.5.12 9:35 AM 5. Alarm Characteristics Carbon Monoxide Alarm Indicator When the alarm senses a dangerous level of CO, the unit will emit a loud alarm pattern. The alarm pattern is four (4) quick beeps followed by five (5) seconds of silence. This cycle repeats as long as a dangerous CO conditions exist. The red Alarm LED will flash the same pattern (and the PPM will be displayed on alarms with digital displays).
2527-7201-00(820-1387A):_ 2008.5.12 9:35 AM Page 16 6. Model KN-COPF-i Operating Characteristics Whenever the alarm is operating, the green Power LED is illuminated and the digital display will display “0” to indicate the unit is monitoring for CO. If the alarm senses dangerous levels of CO, the red Alarm LED will flash, the amber LED will be lit, the digital display will indicate the CO concentration in parts per million (PPM), and the alarm will emit an audible alarm pattern.
2527-7201-00(820-1387A):_ 2008.5.12 9:35 AM Page 17 6. Model KN-COPF-i Operating Characteristics LED Display Shows Alarm Sound Unit Status Recommendation Steady “Err” Red LED flashes every 30 seconds One quick beep every 30 seconds Unit malfunction No display alternating with display of CO concentration every 60 seconds. Red LED flashes with beeps 4 quick beeps, 5 seconds silence, repeating every 60 secs Alarm condition powered on battery backup.
2527-7201-00(820-1387A):_ 2008.5.12 9:35 AM 7. Maintenance NOTE: This unit is sealed. The cover is not removable. Due to the loudness of the alarm, we suggest that you place your fingers over the sounder opening while testing your alarm. CAUTION: Continuous exposure to the high sound level of this alarm over an extended period of time may cause hearing loss. Testing To test the alarm, press the Test/Reset button.
2527-7201-00(820-1387A):_ 2008.5.12 9:35 AM 7. Maintenance Alarm Removal Turn off the power to the alarm. Remove the alarm from the electrical box by unscrewing the four screws under the cover securing the alarm. Disconnect the AC Quick-Connector harness by pulling the connector apart.
2527-7201-00(820-1387A):_ 2008.5.12 9:35 AM SEVEN YEAR LIMITED WARRANTY Warranty Coverage: The manufacturer warrants to the original consumer purchaser, that this product will be free of defects in material and workmanship for a period of seven (7) years from date of purchase. The manufacturer’s liability hereunder is limited to replacement of the product, repair of the product or replacement of the product with repaired product at the discretion of the manufacturer.
