Use and Care Manual
Plug-In Carbon Monoxide Alarm —
AC Powered with Sealed Lithium Battery Backup,
Digital Display, and Escape / Night Light
Part Number: 900-0284
Model KN-COP-DP-10YH
Architectural and Engineering
Specifications
The carbon monoxide alarm shall be Kidde model number KN-COP-
DP-10YH (Part Number 900-0284) or approved equal. It shall be
powered by a 120VAC, 60 Hz source along with a 3V sealed lithium
battery backup. The temperature rating shall be between 40°F and
100°F (4°C and 38°C) and the humidity operating range shall be
10% - 95% relative humidity, non-condensing.
The CO sensor shall be of a fuel cell design and shall meet the sen-
sitivity requirements of Underwriters Laboratories UL2034 Single and
Multiple Station Carbon Monoxide Alarms. The unit shall provide an
accuracy of +/- 30% when reading concentration levels.
The alarm shall include an integral plug that can be installed in any
outlet following the UL/NFPA/Manufacturer’s recommended guide-
lines. The AC blades remain vertical independent of whether the
electrical socket is mounted vertically or horizontally. The unit shall
incorporate a digital display that meets the sensitivity requirements
of UL2034. The display will identify the levels of CO in parts per mil-
lion (ppm) once that level reaches 30ppm. The display will automati-
cally dim in low light conditions, and will turn off when AC power is
removed unless more than 100ppm is detected or in alarm mode.
The alarm shall include a test/reset button. If pressed and released
during normal operation, it shall electronically simulate the presence
of CO and cause the unit to go into alarm. This sequence tests the
unit’s electronics to ensure proper operation. If pressed during alarm
mode, the unit will be silenced and will begin monitoring CO levels
again.
In accordance with UL2034, the CO sensor will not alarm to levels of
CO below 30 ppm and will alarm in the following time range when
exposed to the corresponding levels of CO.
70 ppm CO concentration: 60-240 minutes
150 ppm CO concentration: 10-50 minutes
400 ppm CO concentration: 4-15 minutes
The alarm shall include a piezoelectric horn that is rated at 85 deci-
bels at 10 feet. When the unit detects carbon monoxide, the alarm
pattern will be four (4) short beeps – followed by five (5) seconds
of silence. This pattern repeats as long as dangerous CO conditions
exist. The red Alarm LED will flash the alarm pattern, the escape light
will illuminate, and the PPM will be displayed on the digital display.
See user guide for additional important information.
Ordering Information
Technical
Specifications
Part Number: 900-0284
Model: KN-COP-DP-10YH
Power Source: 120VAC, 60 Hz, 90mA max
Sensor: Electrochemical
Audio Alarm: 85dB at 10ft
Temperature Range: 40˚F (4˚C) to 100˚F (38˚C)
Humidity Range: 10%-95% relative humidity
(RH), non-condensing
Size: 3.0” x 5.6” x 1.5”
Weight: .62 lb.
Interconnects: No
Warranty: 10 year limited
1016 Corporate Park Drive
Mebane NC 27302
1-800-880-6788
www.Kidde.com
Distributed by:
P/N: KL-900-0284 sheet rev. 06-2015
Ordering
No: UPC I 2 of 5
Pack
Cong.
Pack
Qty
Dimensions
(w” x d” x h”) Weight
Cartons/
Pallet
21026350 0-47871-26350-9 100-47871-26350-6 Clam 4 11.25 x 7.94 x 11.5 3.5 60
!
WARNING: This product is intended for use in ordinary
indoor locations of family living units. It is not designed to measure
compliance with Occupational Safety and Health Administration
(OSHA) commercial or industrial standards.
This device is designed to protect individuals from acute effects of
Carbon Monoxide exposure. It will not fully safeguard individu-
als with specic medical conditions. If in doubt, consult a medical
practitioner. Individuals with medical problems may consider using
warning devices which provide audible and visual signals for carbon
monoxide concentrations under 30 ppm.
Industry experts recommend a CO alarm be installed on each level
of the home--ideally on any level with fuel burning appliances and
outside of sleeping areas.– see User Guide for further information.