Owner's Manual

ManualsBrandsKidde ManualsMisc ElectronicsKidde Firex H230 English 110607

INTERCONNECTING HEAT ALARMS

Use 1.5mm

minimum solid or stranded cable with a rating of 230V. When

interconnecting heat alarms and/or smoke alarms, the maximum cable

length between any two should be 450m for 1.5mm

cable (20 ohm loop

resistance.)

This heat alarm may be interconnected with as many as 35 other

Firex Model H230 heat alarms or model GC240, I240C, IAR230C, PG240,

PAD240, PADC240 or PAR230 smoke alarms. DO NOT connect to any

other type of model of heat alarm or smoke alarm. If interconnecting to

Firex Pattress with Relay (Model PATR) only 12 total Firex models may

be interconnected.

Connect all interconnected heat and smoke alarms to a single final cir-

cuit. Wiring must conform to I.E.E. Regulations for Electrical Installations

(BS 7671).

RED AND GREEN LED INDICATORS

This heat alarm features a red and green LED indicator that can be seen

through the clear light pipe on the top of alarm. The LEDs indicate the

following:

GREEN

ON – AC power is present.

OFF – AC power is not present.

RED

BLINKS ONCE A MINUTE – DC power is present indicating

normal operation.

OFF – DC power is not present.

BLINKS ONCE A SECOND and unit is sounding alarm – senses

57°C temperature or greater.

OFF and unit is sounding alarm – Another interconnected

smoke/heat alarm in the network has sensed smoke or 57°C

and is signaling this alarm.

TESTING THE HEAT ALARM

!WARNING: TEST EACH HEAT ALARM AND SMOKE ALARM TO BE SURE THAT EACH IS

INSTALLED CORRECTLY AND IS OPERATING PROPERLY

TAND AT ARM

’S LENGTH FROM THE HEAT ALARM WHEN TESTING. THE ALARM SOUNDER

IS LOUD TO ALERT YOU TO AN EMERGENCY AND CAN BE HARMFUL TO HEARING

EST THE HEAT ALARM WEEKLY AND UPON RETURNING FROM HOLIDAY, OR WHEN THE

HOUSE HAS BEEN UNOCCUPIED FOR SEVERAL DAYS

Test all heat alarms weekly by doing the following:

1. Check the Push-to-Test button. A constant ON green light indicates

the heat alarm is receiving AC power.

2. Firmly depress the Push-to-Test button for at least five (5) seconds.

The heat alarm will sound a loud beep for about four (4) times a

second. The alarm may sound for up to ten (10) seconds after the

Push-to-Test button is released. NOTE: If heat alarms are intercon-

nected, all heat alarms should sound an alarm within three (3)

seconds after any test button is pushed and the tested heat

alarm sounds.

3. If the heat alarm does not sound, turn off the power to the heat

alarm circuit at the main distribution board and check the wiring.

Retest the heat alarm.

!WARNING: IF THE HEAT ALARM SOUNDS, AND THE HEAT ALARM IS NOT BEING TESTED,

THE HEAT ALARM IS SENSING A TEMPERATURE OF 57°C OR ABOVE. THE ALARM

SOUND REQUIRES YOUR IMMEDIATE ATTENTION AND ACTION.

MAINTENANCE AND CLEANING

In addition to weekly testing, this heat alarm must be cleaned periodically

to remove dust, dirt and debris. The battery must also be replaced annually.

!DANGER: ELECTRIC SHOCK HAZARD.

URN OFF THE AC SUPPLY TO THE HEAT ALARM AT THE MAIN DISTRIBUTION BOARD

BY REMOVING THE FUSE OR SWITCHING THE APPROPRIATE CIRCUIT BREAKER TO THE

OFF

POSITION BEFORE REPLACING THE BATTERY OR CLEANING THE HEAT ALARM

BATTERY REPLACEMENT

Always turn off the AC power to the heat alarm before replacing the bat-

tery. Replace the battery at least once annually, or immediately when the

low battery signal sounds once a minute, even though the heat alarm is

receiving AC power.

Use only the following batteries as replacements in this heat alarm:

Eveready 216, 522,1222, Duracell MN1604 or Ultralife UL9V-J.

!WARNING: D

O NOT USE ANY OTHER TYPE OF BATTERY

, EXCEPT AS SPECIFIED IN THIS

MANUAL

. DO NOT USE RECHARGEABLE BATTERIES

1. Turn off the AC power supply to the heat alarm at the main

distribution board.

2. Insert a small screwdriver into the slot in the mounting plate and

turn the heat alarm counterclockwise to detach the alarm.

3. Gently pull down the heat alarm. Be careful not to separate any

wire connections.

4. Pull out the connector plug from the back of the heat alarm.

5. From the back of the heat alarm, remove battery door screw and

lift the tab to open the battery compartment door.

6. Remove the battery from the compartment. Disconnect the

drained battery from the battery compartment and discard.

7. Connect a new, healthy 9V battery to the connector. The battery

will only fit one way. Be sure the battery connector is securely

attached to the battery terminals.

8. Place the battery into the battery compartment.

9. Close the battery compartment door. Push down until it snaps

into place. Install battery door screw.

10. Using the Push-to-Test button, test the heat alarm to verify 9V DC

battery back-up. See “TESTING THE HEAT ALARM”.

11. Replace the connector plug. The connector will “snap” into place.

Gently tug the connector to be sure it is attached properly.

12. Reattach the heat alarm to the mounting plate by turning the heat

alarm clockwise until it snaps into place.

13. Turn on the AC power and test the heat alarm using the

Push-to-Test button. See “TESTING THE HEAT ALARM”.

!WARNING: HEAT ALARMS ARE LIFE-SAVING DEVICES AND SHOULD BE CARED FOR

PERIODICALLY

CLEANING

Clean the heat alarm at least once annually to remove dust, dirt

and debris. Always turn off the AC power to the heat alarm before

cleaning it.

Using the soft brush or wand attachment to a vacuum cleaner,

vacuum all sides and the cover of the heat alarm. Be sure that all

vents are free from debris.

If necessary, turn off the AC power and use a damp cloth to clean the

heat alarm cover.

IMPORTANT: Do not attempt to remove the cover or clean inside the

heat alarm. THIS WILL INVALIDATE YOUR GUARANTEE. Failure to prop-

erly clean and maintain this heat alarm may result in impaired operation

and possible failure and will invalidate the guarantee.

REPAIR

!CAUTION: DO NOT ATTEMPT TO REPAIR THIS HEAT ALARM

. DOING SO WILL INVALI

DATE YOUR GUARANTEE

If the heat alarm is not operating properly, see “TROUBLESHOOTING”.

If necessary, and if the heat alarm is still under guarantee, return it to

your local distributor. Pack it in a well-padded carton and send it, postage

prepaid, to one of the addresses given at the end of this manual.

If the heat alarm is no longer under guarantee, have a qualified electri-

cian replace the heat alarm immediately with a comparable Firex brand

heat alarm.

FIRE SAFETY RULES AND PREVENTING

HAZARDOUS SITUATIONS

Siting, testing, and taking care of heat and smoke alarms is just one step

in helping to protect your family and home from fires. You must also

reduce the chance that fires will start in your home and increase your

chances of escaping if a fire does start. For your safety, as a minimum,

you should do the following to have more effective fire safety.

• Use smoking materials properly – never smoke in bed or when

sleepy or under the influence of alcohol or other drugs.

• Keep matches and other sources of ignition away from children.

• Store flammable materials in proper containers and never store or

use them near open flames or sparks.

• Keep electrical appliances and their leads in good working condi-

tion, and do not overload electrical circuits.

• Keep fireplaces, chimneys, and barbecue grills clean, and make

sure they are properly sited away from combustible materials.

• Keep portable heaters and open flames such as candles away from

combustible materials.

• Do not allow rubbish to accumulate.

• Have the electrical wiring in your house checked by a qualified

electrician at least every 10 years (or more often as it ages).

• Never leave cooking unattended.

FIRE PROCEDURE

If you hear the heat or smoke alarm sounding, and you have not pushed

the test button, it is warning you of a dangerous situation. You will need to

respond immediately. To prepare for such occurrences, develop family

escape plans, discuss them with all household members, and practice

them regularly. For your safety, as a minimum, you should do the following

to have more effective fire safety.

• Draw a floor plan of your home and find all ways to escape if there is

a fire. On the ground floor, consider whether windows can be used

for escape. On upper floors, consider whether external rescue will

be possible if escape routes are cut off by fire or smoke.

• Expose everyone to the sounds of the heat alarm and of the smoke

alarm and explain what the sounds mean. Show them how to check

to see if doors are hot before opening them, how to stay close to

the floor and crawl along the floor to stay below dangerous smoke,

fumes and gases, and how to use the alternative exit if a door is hot.

Instruct them not to open the door if the door is hot.

• Decide on a meeting place a safe distance from your house and

make sure all members of your household understand they should

go and wait for you there if there is a fire. Explain to children that

they must be ready to leave the house by themselves if necessary.

• Hold fire drills every six (6) months to make sure everyone, even

small children, know what to do to escape safely.

• Know where to go to call the Fire Brigade from outside your house.

• Provide emergency equipment, such as fire extinguishers, and teach

your family how and when to use this equipment.

WHAT TO DO IN CASE OF A FIRE

After you have prepared family escape plans and practiced them with

your family, you have increased their chances of escaping safely. Review

the following rules with your children when you have fire drills, so every-

one will remember them in a real fire.

1. Don’t panic, stay calm. Your safe escape may depend on thinking

clearly and remembering what you have practiced.

2. Get out of the house, following your planned escape route,

as quickly as possible. Do not stop to collect anything or to

get dressed.

3. Open doors carefully only after feeling to see if they are hot. Do

not open a door if it is hot; use an alternative escape route. If

your escape route is cut off, go to a window and shout for help.

If necessary, stuff clothing or other materials in the gaps round

the room door to stop smoke entering until help arrives.

4. Stay close to the floor; smoke and hot gases rise toward the

ceiling.

5. Keep doors and windows closed unless you open them to escape.

6. Meet at your pre-arranged meeting place after leaving the house.

7. Call the Fire Brigade as soon as possible from outside your house.

Give your full address, including the name of the town or village.

8. Always call the Fire Brigade as soon as possible, even if a fire

seems small.

9. Never re-enter a burning or smoke-filled building.

These guidelines will assist you in the event of a fire. However, to reduce

the chance that fires will start, practice fire safety rules and prevent haz-

ardous situations. Contact your local Fire Brigade for more information.

TROUBLESHOOTING

GUARANTEE

Maple Chase Company (the “Company”) guarantees this product (except

for the battery) to be free from defects in material and workmanship

under normal use and service (“Defects”) for a period of six (6) years from

the date of purchase (the “Guarantee Period”). Should any Defects be

discovered within the Guarantee Period, the Company will, at its option,

repair or replace the defective product provided that: (a) it is returned

during the Guarantee Period with postage prepaid and with proof of pur-

chase date to the address shown below and (b) the Company verifies that

the claim is proper. This Guarantee does not cover damage resulting from

accident, improper installation, maintenance or repair, misuse, abuse or

product modification. This Guarantee does not confer any rights other

than those expressly set out above and does not cover any claims for

consequential loss or damage. This Guarantee is offered as an extra ben-

efit and does not affect your statutory rights as a consumer.

Return units, postage prepaid, to your local distributor. For information on

your local distributor, contact:

Maple Chase Company

2820 Thatcher Road

Downers Grove, IL 60515-4040 USA

Tel +1-630-719-5500

In the U.K and the Republic of Ireland, contact:

Sensotec Europe Ltd.

Unit 7, Bala Industrial Estate

Bala, Gwynedd LL23 7NL

Tel 01678 520022

BLUE BLUE

ORANGE ORANGE

BROWN BROWN

FOR INTERCONNECTING: USE A MINIMUM OF 1.5mm

CABLE

NEUTRAL

LINE

7 8 9 10 11 12

PROBLEM SOLUTION

Heat alarm does not 1. Check that AC power is

sound when tested. turned on.

2. Turn off power. Remove

heat alarm from mounting

NOTE: Push test button for plate and:

at least five (5) seconds a. Check that connector

while testing! plug is securely attached.

b. Check that battery is

properly attached to

connector.

3. Clean heat alarm.

PROBLEM SOLUTION

Heat alarm beeps about 1. Turn off AC power and

once a minute. replace battery. See

“Battery Replacement” in

the “MAINTENANCE AND

CLEANING” section.

Heat alarm sounds 1. Hire an electrician to move

unwanted alarms. heat alarm to a new location.

See the “HEAT ALARM

PLACEMENT” and “DO NOT

INSTALL HEAT ALARMS”

sections of this manual.

Interconnected heat alarms 1. Press and hold button for at

do not sound when system least three seconds after the

is tested. first unit sounds.

2. Turn off AC power or

circuit breaker and check

the interconnect wiring.

See “INTERCONNECTING

HEAT ALARMS” section

of this manual.

NOTE: Colors shown correspond to electrical codes in the United Kingdom.

Colors may vary in other countries.

110-607.qxd 11/2/00 1:11 PM Page 2