User Guide Combination Photoelectric Smoke & Carbon Monoxide Alarm with Hardwire Interconnect & Voice Model 30CUAR-V Helps Reduce Cooking Nuisance Alarms P/N: G-000001-01 Rev.
Thank You for Purchasing this Kidde Alarm Hardwired for 120V AC, this model includes two replaceable AA backup batteries. It also contains a voice message system and HUSHTM to temporarily silence nuisance alarms, and “self-testing” features (see section 10). Teach children how to respond to the alarm and that they should never play with the unit. This alarm is a multi-criteria device designed to detect both smoke and carbon monoxide from any source of combustion in a residential environment.
Contents 1. Smoke Alarm: What To Do When The Alarm Sounds . . . . . 4 2. Carbon Monoxide Alarm: What To Do When The Alarm Sounds . . . . 5 3. Other Alarm Visual And Audible Indicators . . . . 6 4. Troubleshooting Guide . . . . . . . . . . . . . . . . . . 7 . . . . . . . . . . 5. Introduction, Product Features And Specifications . . . . . . . . . 8 6. Limitations Of Smoke And Carbon Monoxide Alarms . .
1. Smoke Alarm: What To Do When The Alarm Sounds The smoke alarm pattern is three long beeps with voice “Fire!,” a 1.5 second pause, and three long beeps repeating. The red LED blinks in time with the alarm pattern only on the alarm(s) that detected the hazard (initiating alarm). The smoke alarm takes precedence when both smoke and carbon monoxide are present.
2. Carbon Monoxide Alarm: What To Do When The Alarm Sounds The carbon monoxide (CO) alarm pattern is four quick beeps with voice “Warning! Carbon Monoxide” repeating every 5 seconds. The red LED blinks in time with the alarm pattern only on the alarm(s) that detected the hazard (initiating alarm). On DC power only, after 4 minutes in CO alarm the alarm pattern will only occur every 60s. WARNING: ACTUATION OF YOUR CO ALARM INDICATES THE PRESENCE OF CARBON MONOXIDE (CO) WHICH CAN KILL YOU.
If problems are identified during this inspection, have the equipment serviced immediately. Note any combustion equipment not inspected by the technician and consult the manufacturer’s instructions, or contact the manufacturer directly for more information about CO safety and the equipment. Make sure that motor vehicles are not, or have not been, operating in a garage attached or adjacent to the residence. Never restart the source of a CO problem until it has been corrected.
Operational Mode Visual Indications Audible Indications Initiating Alarm (multiple alarms in an interconnected system) Red LED blinks in time with alarm pattern indicating that this is the unit initiating the alarm in an interconnected, multiple alarm, system. NOTE: It is possible for more than one unit to detect a hazard and become an initiating alarm unit (Red LED blinking). Unit in either Smoke or CO alarm mode. Action/Note 4.
Trouble Condition Visual Indications Audible Indications Action End of Unit Life Amber LED blinks 2 times every 60 sec. 2 chirps every 60 sec and voice “Replace Alarm.” After 1 hour, voice occurs only once every 15 mins. Voice “Hush Mode Activated” after button push (first 7 days only). * Push button once to silence for 24 hrs. (Push button again to clear HushTM and perform a test.) Note: 7 days after End of Unit Life begins, the notifications cannot be silenced.
6. Limitations Of Smoke And Carbon Monoxide Alarms WARNING: PLEASE READ CAREFULLY AND THOROUGHLY • Life safety from fire in residential occupancies is based primarily on early notification to occupants of the need to escape, followed by the appropriate egress actions by those occupants. • There are situations where a smoke alarm may not be effective to protect against fire as stated in the NFPA Standard 72.
WARNING: PLEASE READ CAREFULLY AND THOROUGHLY • IMPORTANT: This alarm is designed to detect carbon monoxide gas from ANY source of combustion. It is NOT designed to detect any other gas. CAUTION: This alarm will only indicate the presence of carbon monoxide gas at the sensor. Carbon monoxide gas may be present in other areas. Never restart the source of a CO problem until it has been fixed.
7. Recommended Locations For Smoke And Carbon Monoxide Alarms • Locate smoke alarms in all sleeping areas. Try to monitor the exit path as the bedrooms are usually farthest from the exit. If more than one sleeping area exists, locate additional alarms in each sleeping area. • Locate additional alarms in stairways, because stairways act like chimneys for smoke and heat. • Locate at least one alarm on every floor level. • Locate an alarm in every bedroom.
are to closest edge LIVING KITCHEN ke Alarms forthe Required Detection SIDE ROOM WALL slopes greater than 1 ft in 8 ft (0.3m in 2.4 m) of the NFPA 72 states: “Smoke alarms in rooms with ceiling ke Alarms foralarm. Additional Detection BEDROOM HALL BEDROOM within 6 feet of appliances horizontally shall be located on the high side of the room.” NFPA 72 states: “A row of detectors shall be ING ROOM BEDROOM BASEMENT spaced and located within 3 ftALONG (0.9m) of the peak of the ceiling measured horizontally.
• For mobile home installation, select locations carefully to avoid thermal barriers that may form at the ceiling. For more details, see MOBILE HOME INSTALLATION section. • When mounting the alarm on the wall, use an inside wall with the top edge of the alarm at a maximum of 12” (30.5 cm) below the ceiling. • Put smoke alarms at both ends of a bedroom hallway or large room if the hallway or room is more than 30 feet (9.1 m) long.
8. Locations To Avoid (See Figures 7-A, 7-B, & 7-C for recommended locations) • In the garage. Products of combustion are present when you start your automobile. • Normal cooking may cause nuisance alarms. If a kitchen alarm is desired, it should have an alarm silence feature and should not be installed within 6 ft of cooking appliances. • Do not install within 6 ft of heating appliances. • Less than 4” (10cm) from the peak of an “A” frame type ceiling.
9. Wiring / Installation / Activation NOTE: A dust cover has been installed on the alarm. Keep the dust cover on until all construction has been completed for at least 24 hours (drywall, painting, varnishing, mounting plate install, etc). Retain the dust cover and re-install it to protect the alarm during future construction projects. Construction dust and chemicals can cause contamination and false alarms. BATTERIES. PULL OUT TAB TO ACTIVATE SAQUE LA LENGÜETA PARA S.
Wiring Instructions for AC Quick Connector Harness CAUTION: Turn off the main power to the circuit before wiring the alarm. • For alarms that are used as single station, DO NOT CONNECT THE RED WIRE TO ANYTHING. Leave the red wire insulating cap in place to make certain that the red wire cannot contact any metal parts or the electrical box. • When alarms are hardwire interconnected, all interconnected units must be powered from a single circuit.
NOTE: AC power should be turned off at this stage. Alignment Marks (”A” Line) on • For best results to minimize nuisance Mounting alarms, interconnected alarms should be Bracket on a dedicated line. If not on a dedicated line, it is suggested that the smoke alarms share a lighting load circuit that does not have a dimmer associated with it.
NOTE: Do not grab the shield to install or remove the alarm. Grab the alarm by the outside of the enclosure. (Figure 9-E). ✘ Shield Figure 9-E NOTE: If either battery is missing, the alarm cannot mount on the mounting bracket. Mounting Bracket Note orientation of "A" line. LED Remove Install After fully installed To ensure aesthetic alignment, orient (The button should the unit as shown on the mounting be at the bottom.) bracket and rotate the unit completely until it stops.
AC Wired Interconnect Model Capability This model has AC hardwire interconnect capability. When one hardwired interconnect unit sounds an alarm, all other compatible hardwire or interconnected units will also alarm. NOTE: AC wiring must be completed properly and the AC quick connector must be attached to the unit for the hardwire interconnect function to work.
10. Operation And Testing CO ALARM SENSOR RESPONSE TIMES At 70 PPM, the unit must alarm within 60-240 minutes. This model meets the latest residential smoke At 150 PPM, the unit must alarm within 10-50 minutes. alarm standards, which includes enhanced At 400 PPM, the unit must alarm within 4-15 minutes. resistance to nuisance alarms from cooking. Operation The alarm is operating once it is activated and testing is complete (see “TESTING” below).
11. Recognizing Nuisance Alarms Smoke Nuisance This model meets the latest residential smoke alarm standards, which includes enhanced resistance to nuisance alarms from cooking. HUSH TM : If you know why the alarm is sounding, and you can verify that it is not a life threatening situation, you can push the button on the initiating unit to silence the alarm for 8-10 minutes. If the smoke is not too dense, that unit, and all interconnected units will silence.
12. Battery Backup Press Tab to Release Wire Harness This alarm is powered with AC power, but also contains two replaceable AA backup batteries. Under normal conditions, fresh batteries will last at least one year. In order to access the battery compartment, the wiring harness needs to be removed. To release the wiring harness, press down on the tab as shown in Figure 12-A. Figure 12-A NOTE: Constant exposure to high or low humidity or temperatures may reduce battery life.
13. General Carbon Monoxide (CO) Information Carbon monoxide (CO) is a colorless, odorless, and tasteless poison gas that can be fatal when inhaled. CO inhibits the blood’s capacity to carry oxygen. Possible Sources of CO Inside your home, appliances used for heating and cooking are the most likely sources of CO. Vehicles and other combustion engines running in an attached garage and using a charcoal/gas grill or hibachi in an enclosed area are all possible sources of CO.
Regularly examine vents and chimneys for improper connections, visible rust, or stains, and check for cracks in furnace heat exchangers. Verify that the color of flame is blue on pilot lights and burners. An amber or orange flame is a sign that the fuel is not burning completely and may be releasing CO. Teach all household members what the alarm sounds like and how to respond. Fire Departments, most utility companies and HVAC contractors will perform CO inspections.
14. Cleaning Your Alarm Your Alarm Should be Cleaned at Least Once a Year You can clean the interior of your alarm (sensing chamber) by using compressed air or a vacuum cleaner hose and blowing or vacuuming through the openings around the perimeter of the alarm. The outside of the alarm can be wiped with a clean, dry cloth. Do not use water, detergents or cleaners as they may damage the alarm. NOTE: Do not insert fingers or cleaning items under the shield during cleaning.
• Move the Alarm and place in another location prior to performing any of the following: Staining or stripping wood floors or furniture Painting Wall papering Using adhesives Storing the unit in a plastic bag during any of the above projects will protect the sensors from damage. When household cleaning supplies or similar contaminates are used, the area must be well ventilated. WARNING: REINSTALL THE ALARM AS SOON AS POSSIBLE TO ENSURE CONTINUOUS DETECTION. 15.
Fire Prevention Never smoke in bed or leave cooking food unattended. Teach children never to play with matches or lighters! Train everyone in the home to recognize the smoke alarm pattern and to leave the home using their escape plan when it’s heard. Know how to do “Stop, Drop and Roll” if clothes catch on fire, and how to crawl low under smoke. Install and maintain fire extinguishers on every level of the home and in the kitchen, basement and garage.
California State Fire Marshal Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and areas of the household as follows: A smoke alarm installed in each separate sleeping area (in the vicinity, but outside the bedrooms), heat or smoke detectors in the living rooms, dining rooms, bedrooms, kitchens, hallways, attics, furnace rooms, closets, utility and storage rooms, basements and attached garages. FCC This device complies with part 15 of the FCC Rules.
16. Service And Warranty Ten-Year Limited Warranty Kidde warrants that the enclosed alarm will be free from defects in material and workmanship or design under normal use and service for a period of ten years from the date of purchase.
QUESTIONS OR FOR MORE INFORMATION Call Kidde Product Support line at 1-800-880-6788 or contact us at www.kidde.com Kidde 1016 Corporate Park Drive, Mebane, NC 27302 ©2024 Kidde. All Rights Reserved.
