S)150SC15 Designed for 2015 Ford F150 Super-Cab and Super-Crew vehicles (Compatible in vehicles with or without Sony® System Subwoofer Assembly Subwoofer Harness Amplifier Relocation Bracket (not used on non Sony® trucks) M8 Bolt X 2 M6 Bolt X 2 M6 Nut X 2 Fuse Wire Tie X 6 Adapter Harness Wire Taps Subwoofer Power Harness ©2015 Stillwater Designs S)150SC15-A2-201 1
Power Harness Routing 1. Disconnect negative battery cable. 2. Make sure supplied fuse is not installed in fuse holder and connect the subwoofer power wire to the stud pictured in figure 1. 3. Route the power harness toward and along the firewall and secure with supplied wire ties. 4. Make a small incision in the grommet on the driver side of the firewall and pass the power harness into the cabin. Fig. 2 5. Install the black two pin power connector on the subwoofer power harness.
8. Remove the driver side front and rear threshold panel along the bottom of the door opening by prying up. 9. Snap loose the driver’s side kick panel. 10. Connect the subwoofer harness black two-pin power connector to the power harness black twopin connector. 11. Connect the subwoofer harness white two pin signal input connector to the corresponding white connector of the adaptor harness. Input Connection Non Sony® Equipped Truck (For trucks equipped with Sony, skip to step 25) 12.
Subwoofer Mounting Non Sony Equipped Trucks 15. Fold down the driver’s side rear seatback by first raising the seat bottom to the up position. Reach behind the seat back approximately 5 inches from the outer edge of the seatback and approximately 7 inches below the top edge of the seat back. Feel for the mechanism pictured in Fig. 6 (Note: Orientation shown is with seatback already folded down) and locate the metal pin indicated by the arrow and pull up to release seatback.
2” 2 ½” 5” 3 ½” Fig. 8 19. Connect the subwoofer harness four pin connector to the subwoofer and engage the red locking tab by sliding sideways. Next connect the subwoofer harness ten pin connector to the subwoofer, engage the red locking tab and then attach the connector to the bracket as shown in Fig. 9 20. Set the subwoofer in place and line up the screw clips in the upper bracket with the rectangular holes in the back of the cab.
21. Line up the lower subwoofer brackets and install the supplied bolts. Fig. 11 and Fig. 12 Fig. 11 Fig. 12 22. Reinstall all previously removed parts in reverse order. 23. Install supplied fuses into fuse holders. 24. Reconnect negative battery cable. Input Connection for Sony® Equipped Truck 25. Remove the tape from the factory wire harness just behind the junction of the harness that proceeds up the B pillar post between the front and rear door opening on the driver’s side of the vehicle. Fig. 13 26.
Sony Amplifier Relocation and Factory Subwoofer Removal (Sony Equipped Trucks Only) 29. Remove the retainer securing the factory amplifier connector cover and disconnect the amplifier connectors. Fig. 14 30. Remove the two nuts and one bolt securing the factory subwoofer. Disconnect factory subwoofer wiring and remove factory subwoofer. Fig. 15-17 Fig. 14 Fig. 15 Fig. 16 Fig. 17 31.
32. Remove the passenger side factory subwoofer mounting stud. Fig. 20 33. Remove the four screws securing the factory amplifier to its bracket. Fig. 21 Fig. 20 Fig. 21 34. Install the factory amplifier on the relocation bracket using the supplied nuts (X2) and bolts (X2). Make sure the nuts are installed on the amplifier side as shown in Fig. 22 35. Cut the carpet section indicated in Fig. 23 and remove to allow the amplifier relocation bracket to install. Fig. 23 1 ½” Fig. 22 36.
38. Remove the two screw clips and screws from the replacement subwoofer mounting bracket. (These are only used for trucks not originally equipped with subwoofers) 39. Connect the subwoofer harness four pin connector to the subwoofer and engage the red locking tab by sliding sideways. Next connect the subwoofer harness ten pin connector to the subwoofer, engage the red locking tab and then attach the connector to the bracket as shown in Fig. 29 40.
Troubleshooting the Kicker Integrated Systems If you experience a problem once the subwoofer or amplifier are installed use this guide to locate the trouble. The radio is working, but the Subwoofer is not working: x x x x x x x x Check the battery voltage to make sure it is not discharged below 11 volts. Check the negative battery cable to see if it has been securely tightened back on the battery. Check the inline fuse located near the battery to make sure it is plugged in completely, and not blown.
If you continue to experience problems after troubleshooting, please contact KICKER Technical Support at (800) 256-0808 ext. 6009, or support@kicker.com. P.O.
