Installation Guide

IMPORTANT SAFETY INSTRUCTIONS
LIGHTED BULB IS HOT!
WARNING: To reduce the risk of FIRE or INJURY TO PERSON:
• Turnoffandallowtocoolbeforereplacingbulb.
• BulbgetsHOTQUICKLY!Contactswitchonlywhenturningoff.
• DONOTremaininlightifskinfeelswarm.(Lightisintense,
 maycause“sunburn”)
• DONOTlookdirectlyatlightedbulb.
• Keepmaterialsawayfrombulbthatmayburn.
• UseONLYwithwattagespeciedorlower.
• DONOTtouchbulbatanytime,useasoftcloth.Oilfromskin
 maydamagebulb.
• DONOToperatexturewithmissingordamagedglass.
1) TURN OFF POWER.
IMPORTANT:Beforeyoustart,NEVERattemptanywork
  withoutshuttingofftheelectricityuntiltheworkisdone.
  a) Gotothemainfuse,orcircuitbreaker,boxinyour 
   home.Placethemainpowerswitchinthe“OFF” 
   position.
  b) Unscrewthefuse(s),orswitch“OFF”thecircuitbreaker
   switch(s),thatcontrolthepowertothextureorroom
   thatyouareworkingon.
  c) Placethewallswitchinthe“OFF”position.Ifthexture
   tobereplacedhasaswitchorpullchain,placethosein
   the“OFF”position.
2) Findtheappropriatethreadedholesonmountingstrap. 
  Assemblemountingscrewsintothreadedholes.
3) Attachmountingstraptooutletbox.(Screwsnotprovided).
  Mountingstrapcanbeadjustedtosuitpositionofxture.
4) Groundinginstructions:(SeeIllus.AorB).
  A) Onxtureswheremountingstrapisprovidedwithahole
   andtworaisedimples.Wrapgroundwirefromoutlet
   boxaroundgreengroundscrew,andthreadintohole.
  B) Onxtureswhereacuppedwasherisprovided.Attach
   groundwirefromoutletboxundercuppedwasherand
   greengroundscrew,andthreadintomountingstrap.
  Ifxtureisprovidedwithgroundwire.Connectxture 
  groundwiretooutletboxgroundwirewithwireconnector.
  (Notprovided.)Afterfollowingtheabovesteps.Neverconnect
  groundwiretoblackorwhitepowersupplywires.
5) Makewireconnections(connectorsnotprovided.)Reference
  chartbelowforcorrectconnectionsandwireaccordingly.
6) Pushxturetowall,carefullypassingmountingscrews
  throughholes.
7) Securexturetowallusingthreadedballs.
8) Setglassdownoversocket.
9)  Threadsocketringontosocket.(DONOTovertighten.)
10) Insertrecommendedbulb.CAUTION: DONOTtouchbulb
  withbarehands.Ifthishappens,cleanbulbwithdenatured
  alcoholandalintfreecloth.
11) Slipglasssleeveoverbulb.
DateIssued:8/9/13 IS-45478-US
MOUNTINGSTRAP
PLANCHAPARAMONTAR
GLASS
VIDRIO
GREEN GROUND
SCREW
CUPPED
WASHER
A
B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
THREADEDCAP
BOLAROSCADO
BULB
BOMBILLA
GLASSSLEEVE
CAMISADEVIDRIO
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
SOCKETRING
ANILLODELCASQUILLO