Installation Sheet

Date Issued: 04/18/16 IS-43926-US
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
1) Get the canopy with opening upward. Pass small threaded
nipple thru center hole in canopy. Pass lockwasher over
small threaded nipple. Thread hexnut onto small threaded
nipple and tighten to secure.
2) Pass fixture wire thru tube. Thread tube over threaded
nipple protruding from above fixture. Tighten to secure.
3) Pass fixture wire thru upper trim and canopy assembly.
Thread upper trim and canopy assembly into tube. Tighten
to secure.
4) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a. Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b. Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c. Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
5) Find the appropriate threaded holes on mounting strap. As-
semble mounting screws into threaded holes.
6) Attach mounting strap to outlet box. Mounting strap can be
adjusted to suit position of fixture.
7) Grounding instructions: (See Illus. A or B)
A. On fixtures where mounting strap is provided with a
hole and two raise dimples. Wrap ground wire from
outlet box around green ground screw, and thread into
hole.
B. On fixtures where a cupped washer is provided. Put
ground wire from outlet box under cupped washer
and green ground screw and thread screw into hole in
mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector,
after following the above steps. Never connect ground wire
to black or white power supply wires.
8) Make wire connections. Reference chart below for correct
connections and wire accordingly.
9) Push fixture to ceiling, carefully passing mounting screws
through holes in canopy. Make sure all wires are inside
canopy and do not get pinched between canopy and ceiling.
10) Thread lockup knobs onto mounting screw and tighten to
secure fixture to ceiling.
11) Insert recommended bulbs.
SEMI-FLUSH MOUNT
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
A
B
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
12) Thread hexnut onto threaded nipple leaving approximately
3/8-1/2 inch thread showing.
13) Using same end of threaded nipple, thread threaded nipple
into coupling just below sockets. Make sure threaded
nipple does not protrude pass opening in coupling.
14) Thread hexnut on threaded nipple up to coupling. Secure by
holding coupling and tighten hexnut with wrenches.
15) Thread hexnut on bottom of nipple leaving approximately
5/8-in threads showing.
16) Pass washer first and then rubber washer onto threaded
nipple.
17) Raise glass up passing threaded nipple thru hole in center of
glass. Check to determine when the glass touches the rub-
ber washer, the top of glass should be touching bottom of
fixture. It may be required to lower glass and adjust hexnut
up/down until you are able to bottom out on both rubber
washer and top of glass.
18) Once correct glass alignment is achieved, pass rubber
washer first and then washer onto threaded nipple. Thread
long hexnut onto threaded nipple. Tighten long hexnut to
secure glass. (DO NOT over tighten.)
19) Pass Trim (small hole) over threaded end of finial. Raise trim
and finial together and thread finial on end of long hexnut.
Tighten to secure. DO NOT over tighten.