Installation Guide

IMPORTANT SAFETY INSTRUCTIONS
LIGHTED BULB IS HOT!
WARNING: To reduce the risk of FIRE or INJURY TO PERSON:
• Turn off and allow to cool before replacing bulb.
• Bulb gets HOT QUICKLY! Contact switch only when turning
off.
• DO NOT remain in light if skin feels warm. (Light is intense,
may cause “sunburn”)
• DO NOT look directly at lighted bulb.
• Keep materials away from bulb that may burn.
• Use ONLY with wattage specified or lower.
• DO NOT touch bulb at any time, use a soft cloth. Oil from skin
may damage bulb.
• DO NOT operate fixture with missing or damaged glass.
1) Pass fixture wire from each coupling on top of fixture
through one stem for each side and screw each stem into
each coupling. NOTE: Thread locking compound must be
applied to all stem threads as noted with symbol (3) to
prevent accidental rotation of fixture during cleaning,
relamping, etc.
2) Pass fixture wire through remaining stems and screw stems
together.
3) Thread one small threaded pipe into end of each small loop.
4) Pass fixture wire through first loop. Thread one first loop
onto end of each last stem.
5) Attach one chain link to each small loop at end of each
stem. Then attach each chain link to one second small loop.
6) From each stem, pass fixture wire through each second
loop. Then from each second loop, pass fixture wire through
each hole in canopy. Pass threaded pipe at end of each
second loop through each hole in canopy.
7) On one side, pass fixture wire from threaded pipe protruding
from inside canopy through hole in one lockwasher. Thread
lockwasher onto end of threaded pipe.
8) From the same side as step 7, pass fixture wire through hole
in hexnut. Thread hexnut onto end of threaded pipe.
9) Repeat steps 7 and 8 to attach other stem to canopy.
10) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
MOUNTING STRAP
ABRAZADERA DE MONTAJE
CANOPY
ESCUDETE
Date Issued: 9/4/15 IS-43580-US
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
KNURL KNOB
PERILLA ESTRADA
SMALL LOOP
ARGOLLA
PEQUEÑA
CHAIN LINK
ESLABÓN DE CADENA
STEM
VASTAGO
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
11) Find the appropriate threaded holes on mounting strap.
Assemble mounting screws into threaded holes.
12) Attach mounting strap to outlet box. (Screws not provided).
Mounting strap can be adjusted to suit position of fixture.
13) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into
hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector
(not provided.) after following the above steps. Never
connect ground wire to black or white power supply wires.
14) Make wire connections (connectors not provided). Reference
chart below for correct connections and wire accordingly.
15) Push fixture to ceiling, carefully passing mounting screws
through holes in canopy.
16) Thread knurl knobs onto mounting screws. Tighten knurl
knobs to secure fixture to ceiling.
17) Insert recommended bulb. CAUTION: DO NOT touch bulb
with bare hands. If this happens, clean bulb with denatured
alcohol and a lint free cloth.
18) Lower glass down towards fixture. Carefully pass hole in
bottom of glass over bulb. Set glass down on socket cup.
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
3
3
3
GREEN GROUND
SCREW
CUPPED
WASHER
A
B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
3
GLASS
VIDRIO
BULB
BOMBILLA
SOCKET CUP
CASQUILLO DEL
PORTALÁMPARAS