Installation Guide
11) Make wire connections (connectors not provided.) Reference
chart below for correct connections and wire accordingly.
12) Carefully push wire connections back into outlet box making
sure all connections remain secure.
13) Slip canopy over mounting screws and backpan. NOTE: Be
certain wires do not get pinched between backpan and
canopy.
14) Secure canopy to backpan using threaded caps.
15) Set glass down over socket.
16) Thread socket ring onto socket. (DO NOT over tighten.)
17) Insert recommended bulb. CAUTION: DO NOT touch bulb
with bare hands. If this happens, clean bulb with denatured
alcohol and a lint free cloth.
18) Slip glass sleeve over bulb.
LOOP/CHAIN LINK MOUNT
1) Follow steps 1, 2, and 3 from Stem Mount Instructions.
2) Screw loops onto end of each threaded pipe.
3) Add one chain link to each loop and add second loop to each
chain link.
4) Screw threaded pipe into end of each loop.
5) Pass each threaded pipe on loops through holes in canopy.
6) Slip one lockwasher over end of each threaded pipe and
screw one hexnut onto threaded pipes.
7) Follow steps 6 - 18 from Stem Mount Instructions.
IMPORTANT SAFETY INSTRUCTIONS
LIGHTED BULB IS HOT!
WARNING: To reduce the risk of FIRE or INJURY TO PERSON:
• Turnoffandallowtocoolbeforereplacingbulb.
• BulbgetsHOTQUICKLY!Contactswitchonlywhenturningoff.
• DONOTremaininlightifskinfeelswarm.(Lightisintense,
may cause “sunburn”)
• DONOTlookdirectlyatlightedbulb.
• Keepmaterialsawayfrombulbthatmayburn.
• UseONLYwithwattagespeciedorlower.
• DONOTtouchbulbatanytime,useasoftcloth.Oilfromskin
may damage bulb.
• DONOToperatexturewithmissingordamagedglass.
RIGID STEM MOUNT
1) Pass wire through stems and screw stems into couplings on
topofxturebody.
NOTE: Thread locking compound must be applied to all stem
threads as noted with symbol (3) to prevent accidental
rotationofxtureduringcleaning,relamping,etc.
2) Passxturewirethroughremainingstemsandscrewstems
together.
3) Screw small threaded pipe onto top of stems.
4) Pass holes in canopy over threaded pipe on top of stems.
5) Slip lockwasher over end of each threaded pipe and screw
hexnut onto end of each threaded pipe.
6) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s),thatcontrolthepowertothextureorroomthat
you are working on.
c) Placethewallswitchinthe“OFF”position.Ifthextureto
be replaced has a switch or pull chain, place those in the
“OFF” position.
7) At the center of the backpan are knockout slots. Remove the
set that matches your outlet box.
8) Secure the backpan to the outlet box.
9) Anchor the backpan to the ceiling using the set of holes at
eachendofxtureusingwoodscrews,togglebolts,plastic
anchors, etc.
10)Connectxturegroundwiretooutletboxgroundwirewith
wire connector. Never connect ground wire to black or white
power supply wire.
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
IS-42017-CBDate Issued: 12/28/12
INSTRUCTIONS
For Assembling and Installing Fixtures in Canada
Pour L’assemblage et L’installation Au Canada
THREADEDPIPE
TUBO ROSCADO
RIGID STEM MOUNT
INSTALLATION SUR TIGE
CANNELÉE
STEM
TIGE
HEXNUT
ECROU
HEXAGONAL
THREADEDCAP
BOUTONMOLETÉ
LOOP/CHAIN LINK
BOUCLE/MAILLON DE CHAÎNE
BACKPAN
PANNEAU ARRIÈRE
GLASS
VERRE
CANOPY
CACHE
STEM
TIGE
LOOP
BOUCLE
CHAINLINK
MAILLONDE
CHAÎNE
3
THREADEDCAP
BOUTONMOLETÉ
SOCKETRING
ANNEAUDELA
DOUILLE
BULB
L’AMPOULE
GLASSSLEEVE
MANCHONDEVERRE


