Owner's Manual

Owner’s Guide
SE8
WHAT ’S IN THE CARTON
Contents
Confirm that the following parts are included:
USB cable 3.5 mm audio cable
Note: If any part of your product is damaged, do not use it. Contact your authorized customer service.
Active noise cancelling Bluetooth headphones Carry case
Airline headphone adapter
3.5mm to 6.5mm audio converter
HEADP H ONE CONTROLS
Noise cancellation on/Off switch
Volume up / Skip forward button
Power / Bluetooth / Call control button
Volume down / Skip backward button
USB Type-C charging port
Audio jack
Press and hold for 1.5 seconds, until the indicator light
on blue one second and hearing the "power-on" tones.
Press and hold for 3.5 seconds, until the indicator light
on red one second and hearing the "power-off" tones.
Power on
Short press the button
Short press the button
Press and hold for one 2 seconds
While on a call, press once
While on a call, press and hold for 2 seconds
With two active calls, press once
Short press the Multi-function button
Long press the button
Long press the button
Short press the button
Short press the button
The Multi-function button and microphone are located on the back of the right earcup.
HEAD PHONE CONTROLS
Headphone functions
Media playback and volume functions
Call functions
The headphone controls are located on the right earcup.
Function What to do
Play /Pause
Skip forward
Skip backward
Volume up
Volume down
Function What to do
Answer a call
End a call
Decline an incoming call
Answer a second incoming call
and put the current call on hold
Decline a second incoming call
and stay on current call
Switch between two calls
NOIS E C A N C E LLA TION & AMBIENT SOUN R
Noise Cancelling Modes
Active Noise cancellation (ANC) reduces unwanted noise providing a clearer, more lifelike audio performance. You can choose the noise
cancelling mode based on your listening preferences and environment.
Ambient Sound Modes
Turn on Ambient modes to control how much surrounding noise you let in. With Quick Ambient Mode, you can listen in on street traffic,
catch flight announcements, and hear when your kids or coworkers call out to you.
Summary: Turn on the noise Cancellation function of your headphones if you want to listen to music without the interruption of
surrounding noise. Turn on Ambient Sound Mode if you want to hear the sounds around you.
Switch Between Noise Cancellation and Ambient Sound Modes
Active Noise Cancelling
Active Noise Cancelling (ANC) mainly focuses on cancelling out lower frequency sounds like engines, aviation environment, trains,
traffic noise, etc, so our valuable customers can focus on their music, movies, or books without being disturbed by outside noises. Our
ANC headphones incorporate a microchip that measures ambient sound and generate a waveform that is an exact negative of the
ambient sound and mix it with any audio signal our customers desires. Making it possible to listen to audio content without raising the
volume excessively. Please do note, ANC does not cancel out noises like snoring, talking, music or high-frequency sounds, etc.
B A T T E RY CHA RGIN G
Charge the headphones
Notes:
• While charging, the battery indicator red. The battery light turns off when the battery is fully charged.
• If the power is lower than 10%, you will hear the "Battery Low" tone, prompting every 3 minutes, until the battery is completely
used up and automatically shuts down.
Notes:
• When only use Bluetooth without noise cancelling, a full charge powers the headphones for up to 25 hours.
• When use Bluetooth with noise cancelling, a full charge powers the headphones for up to 20 hours.
Charging time
Allow up to 5 hours to fully charge the headphones.
1. Plug the small end of the USB cable into the USB Type-C connector on the left earcup.
2. Plug the other end into a USB wall charger or computer that is powered on.
1, Please make sure headphone is turn on;
2, Short press the NC button, enable the noise canceling function;
3, Short press the NC button again, switch to Ambient Sound Mode;
4, Short press the NC button again, both noise canceling function and Ambient Sound Mode is off.
Tip: Each press of the NC button changes the function. Loop in turn.
STAT US INDICATORS
BLUETOOTH CONNECTIONS
Connection method
You can connect your mobile device with your headphones using Bluetooth wireless technology.
Note: If connected to an Apple device, the device displays the headphone battery level near the upper right corner of the screen.
Note: The devices must be within range (49.2 ft. or 15 m) and powered on.
Tip: Once powered on, the LED flashes blue and red alternately.
Tip: Once paired, you hear “Connected” and see the indicator flash blue slowly.
Choose “SE8” to connect
2. On your mobile device, enable the Bluetooth feature.
Tip: The Bluetooth feature is usually found in the Setting menu.
3. Select your headphones from the device list.
1.Turn on the headset. If connecting for the first time, the headphone will
enter the pairing mode automatically after it is powered on.
SE8
Solid green Noise cancellation ON
Indicator Light Display
Flashing blue and red alternately
Flashing red
Solid red
Solid blue
Flashing blue slowly
System status
Power on & In pairing mode
Low Battery
Charging in Process
Fully Charged
Paired
Indicator Light Display System status
Connect using the Bluetooth menu on your mobile device
BLUET OOTH CONNECTIONS
Disconnect a mobile device
Reconnect a mobile device
Connect another mobile device
1. Use the Bluetooth menu on your mobile device to disconnect your mobile device.
2. Power off headphones.
When powered on, the headphones try to reconnect with the last-paired device.
Note: The devices must be within range (49.2 ft. or 15 m) and powered on.
1.Disconnected on your first mobile device.
2.Connected on your second mobile device.
Note: You only can connect one device at a time.
Clear the headphone pairing list
1. Press and simultaneously and hold for 3.5 seconds.
2. Delete your headphones from the Bluetooth list on your mobile device. All devices are cleared and the headphones are ready to
connect.
WIRE D CON NECT IONS
CARE AND MAINTENANCE
Clean the headphones
Your headphones may require periodic cleaning.
• Wipe the outside surfaces with a soft, dry cloth.
• Don’t allow moisture to get inside the earcups or the audio input connector.
Connect the audio cable
Use the 3.5 mm cable (provided) to connect a non-wireless device or to continue using the headphones.
Airline Headphone Adapter3.5mm to 6.5mm Audio Converter
Store your headphones
Place the headphones flat into the case.
Notes: • Make sure to power off the headphones when not in use.
• Before storing the headphones for more than a few months, make sure the battery is fully charged.
3.5mm 6.5mm
T ROUBLESHOOTING
Common solutions
If you experience problems with your headphones:
• Check the state of the status indicators (see page 10).
• Charge the battery (see page 9).
• Increase the volume on your headphones, mobile device and music app.
• Try connecting another mobile device (see page 11).
If you could not resolve your issue, see the table below to identify symptoms and solutions to common problems. If you are unable to
resolve your issue.
Symptom Solution
Headphones don’t power on Charge the battery.
Poor sound quality
• Use a different music source.
• Connect another mobile device (see page 11).
• Disconnect the second device.
• Move your mobile device closer to the headphones and away from any
interference or obstructions.
Headphones don’t connect
with your mobile device
• Check the state of the status indicators(see page 10).
• Disconnect the back-up audio cable.
• Disconnect the USB charging cable.
• On your mobile device:
- Disable the Bluetooth feature and then re-enable.
- Delete your SE8 from the Bluetooth list on your device. Connect again.
• Move your mobile device closer to the headphones and away from any
interference or obstructions.
• Connect another mobile device (see page 11).
• Visit www.cowinaudio.com to see how-to videos.
• Clear the headphone pairing list (see page 11) and connect again.
Symptom Solution
No sound
Cannot hear on a call
• Power on the headphones and charge the battery.
• Check the state of the status indicators (see page 10).
• Increase the volume on your headphones, your mobile device and music source.
• Slide the Power/Bluetooth switch to the right and release to hear the connected
device. Make sure you are using the correct device.
• Move your mobile device closer to the headphones and away from any
interference or obstructions.
• Use a different music source.
• Connect another mobile device (see page 11).
Noise beeping
Bad Bluetooth connect
• If the Bluetooth signal is weak, out of range or interferes, the Bluetooth® wireless
connection may fail or the sound cuts in and out. Please see the information below to improve
signal quality and reduce the possibility of interference.
• The Bluetooth wireless connection may fail or the sound will continue to cut in and out.
These due to weak Bluetooth signals or external signal interference. Please away from any
interference or obstructions.
• Bluetooth headphone and device distance is less than 15M, Bluetooth and mobile phone
are in the same direction. Move your mobile device closer to the headphones.
• The battery is running out of power, use it after charging.
• Check if the network signal is OK (whether the player is in buffer).
• The compatibility between the headphone and the Bluetooth device is not good, replace the
device with a higher Bluetooth version.
• Check that headphones and the connected device (i.e., smartphone) are turned on.
• Turn up the volume of the connected device if it is too low.
• Check the audio settings of the Bluetooth device to make sure the sound comes from the
headphones during a call.
• Re-establish the connection using the Bluetooth device.
• While listening to music with the headphones, stop playback and press the button on the
right or left unit to respond to an incoming call.
• Due to weak Bluetooth signals or external signal interference. In this case, move away from
wireless routers or microwaves and move your headphone closer to the Bluetooth device.
• Avoid using the headphones for a long time, otherwise the sound will be intermittent,
please reuse after a period of rest.
Listen to music when the
battery is discharged
• Even in wired mode, the battery power need to use, the headphones do not support the use
of no power.
Symptom Solution
No sound from a device
connected by the back-up
audio cable
Poor sound quality from a
device connected by audio cable
Battery won’t charge
• Secure the ends of the back-up audio cable.
• Increase the volume on your headphones, your mobile device and music source.
• Connect another device (see page 11).
• Secure the ends of the back-up audio cable.
• Connect another device (see page 11).
• Secure the ends of the USB charging cable.
• Try another charging source.
• If your headphones have been exposed to high or low temperatures,
let the headphones return to room temperature and try charging again.
Noise cancelling function
doesn't work
• Make sure that the noise canceling function is turned on.
• Are the ears all wrapped and re-equipped.Adjust the earpad position to fit your ears.If the
earmuffs are loose, re-set the ear.
• Eliminate low frequency noise? The noise canceling function is effective in low frequency
ranges such as airplanes, trains, offices, near air-conditioning, and is not as effective for
higher frequencies, such as human voices.
ANC Wireless Headphones
15107-000565 SE8说明书 145*105MM/70克书写纸/3*2折页/正反单色印刷
正面
反面
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
— Consult the dealer or an experienced radio/ TV technician for help.
Any changes or modifications to this device not explicitly approved by manufacturer could
void your authority to operate this equipment.
The device has been evaluated to meet general RF exposure requirement. The device can
be used in portable exposure condition without restriction.