User Manual

928 Keysight InfiniiVision 1000 X-Series Oscilloscopes Programmer's Guide
Index
sweep speed set to fast to measure rise
time, 368
switch disable, 540
sync break, LIN, 490
syntax elements, 103
syntax rules, program data, 786
syntax, optional terms, 103
syntax, program message, 783
SYSTem commands, 535
system commands, 537, 538, 539, 540,
555, 557
system commands introduction, 536
T
tdelta, 718
tedge, 373
telnet ports 5024 and 5025, 628
temporary message, 538
TER (Trigger Event Register), 163, 758
termination conditions, mask test, 408
test sigma, mask test run, 413
test, self, 130
text, writing to display, 538
threshold voltage (lower) for
measurement, 716
threshold voltage (upper) for
measurement, 725
thresholds, 352, 719
thresholds used to measure period, 363
thresholds, how autoscale affects, 137
time base, 561, 562, 563, 564, 565, 740
time base commands introduction, 560
time base reset conditions, 122, 545
time base window, 567, 568, 569
time between points, 718
time buckets, 177, 178
time delay, 740
time delta, 718
time difference between data points, 648
time duration, 595
time holdoff for trigger, 576
time interval, 373, 375, 718
time interval between trigger and
occurrence, 724
time marker sets start time, 719
time measurements with X cursors, 330
time per division, 563
time record, 268, 295
time specified, 384
time, calibration, 198
time, mask test run, 414
time, start marker, 722
time, stop marker, 723
time, system, 557
time, transition trigger, 612
time/div, how autoscale affects, 137
time-at-max measurement, 720
time-at-min measurement, 721
TIMebase commands, 559
timebase vernier, 566
TIMebase:MODE, 46
time-ordered label list, 235
timeout, SPI clock, 501
timing measurement, 345
title channels, 208
title, mask test, 422
tolerance, automask, 398, 399
top of waveform value measured, 385
total frame count (CAN), 461
total waveforms in mask test, 403
trace memory, 161
track measurements, 370
transfer instrument state, 117, 555
transition trigger qualifier, 609
transition trigger slope, 610
transition trigger source, 611
transition trigger time, 612
transparent screen background, remote
command logging, 553
tree traversal rules, 787
TRG (Trigger), 126, 128, 129
TRIG OUT BNC, 193
trigger armed event register, 150, 152
trigger burst, UART, 528
trigger channel source, 596, 617
TRIGger commands, 571
TRIGger commands, general, 573
trigger data, UART, 529
TRIGger EDGE commands, 583
trigger edge coupling, 584
trigger edge slope, 587
trigger event bit, 163
Trigger Event Register (TER), 758
TRIGger GLITch commands, 589
trigger holdoff, 576
trigger idle, UART, 530
TRIGger IIC commands, 473
trigger level auto set up, 577
trigger level constants, 210
trigger level voltage, 585
trigger level, high, 578
trigger level, low, 579
TRIGger LIN commands, 483
trigger occurred, 128
TRIGger PATTern commands, 597
trigger pattern qualifier, 601
trigger qualifier, UART, 531
trigger reset conditions, 122, 545
TRIGger SHOLd commands, 602
trigger SPI clock slope, 500
TRIGger SPI commands, 497
trigger status bit, 163
trigger sweep mode, 571
TRIGger TV commands, 608, 613
trigger type, SPI, 511
trigger type, UART, 532
TRIGger UART commands, 513
trigger, CAN, 467
trigger, CAN pattern data length, 470
trigger, CAN pattern ID mode, 472
trigger, CAN sample point, 463
trigger, CAN signal baudrate, 464
trigger, CAN signal definition, 465
trigger, CAN source, 466
trigger, edge coupling, 584
trigger, edge level, 585
trigger, edge reject, 586
trigger, edge slope, 587
trigger, edge source, 588
trigger, force a, 574
trigger, glitch greater than, 590
trigger, glitch less than, 591
trigger, glitch level, 592
trigger, glitch polarity, 593
trigger, glitch qualifier, 594
trigger, glitch range, 595
trigger, glitch source, 596
trigger, high frequency reject filter, 575
trigger, holdoff, 576
trigger, IIC clock source, 475
trigger, IIC data source, 476
trigger, IIC pattern address, 477
trigger, IIC pattern data, 478
trigger, IIC pattern data 2, 479
trigger, IIC qualifier, 480
trigger, IIC signal baudrate, 487
trigger, IIC type, 481
trigger, LIN, 491
trigger, LIN pattern data, 493
trigger, LIN pattern data length, 495
trigger, LIN pattern format, 496
trigger, LIN sample point, 486
trigger, LIN source, 488
trigger, mode, 580
trigger, noise reject filter, 581
trigger, SPI clock slope, 500
trigger, SPI clock source, 503
trigger, SPI clock timeout, 501
trigger, SPI frame source, 504
trigger, SPI framing, 502
trigger, SPI pattern MISO width, 508
trigger, SPI pattern MOSI width, 510
trigger, sweep, 582
trigger, TV line, 614
trigger, TV mode, 615, 741
trigger, TV polarity, 616
trigger, TV source, 617
trigger, TV standard, 618
trigger, UART base, 527
trigger, UART baudrate, 516
trigger, UART bit order, 517
trigger, UART parity, 523
trigger, UART polarity, 524
trigger, UART Rx source, 525
trigger, UART Tx source, 526
trigger, UART width, 533
truncation rules, 784
TST (Self Test), 130
tstart, 722
tstop, 723
turn function on or off, 710
turn off channel, 142
turn off channel labels, 234
turn off math function, 142