User Manual

Index
Keysight InfiniiVision 1000 X-Series Oscilloscopes Programmer's Guide 927
saved image, area, 739
saving and recalling data, 226
SBUS CAN commands, 456
SBUS commands, 451
SBUS<n> commands, general, 453
scale, 264, 305, 565, 569
scale factors output on hardcopy, 313, 436
scale for channels, 217
scale units for channels, 218
scale units for external trigger, 256
scaling display factors, 210
SCPI.NET examples, 917
scratch measurements, 717
screen area for hardcopy print, 311
screen area for saved image, 739
screen display of logged remote commands,
enable/disable, 550
screen image data, 232
SECAM, 614, 618
seconds per division, 565
segmented waveform save option, 448
segments, analyze, 181
segments, count of waveform, 638
segments, setting number of memory, 182
segments, setting the index, 183
segments, time tag, 639
select measurement channel, 371
self-test, 130
sensing a channel probe, 705
sensing a external trigger probe, 708
sensitivity of oscilloscope input, 210
sequential commands, 790
serial clock, 475, 503
serial data, 476
serial decode bus, 451
serial decode bus display, 454
serial decode mode, 455
serial frame, 504
serial number, 159
service request, 128
Service Request Enable Register
(SRE), 126, 757
set center frequency, 259, 291
set cursors, 722, 723
set date, 537
set time, 557
set up oscilloscope, 35
setting display, 290
setting external trigger level, 248
setting impedance for channels, 206
setting inversion for channels, 207
settings, 120, 124
settings, instrument, 310
setup, 176, 201, 226, 310, 555
setup and hold trigger clock source, 604
setup and hold trigger data source, 605
setup and hold trigger hold time, 606
setup and hold trigger setup time, 607
setup and hold trigger slope, 603
setup configuration, 120, 124, 555
setup defaults, 121, 544
setup memory, 120
setup reported, 572
setup time, setup and hold trigger, 607
setup, recall, 428
setup, save, 443
shape of modulation signal, waveform
generator, 671
SHOLd trigger commands, 602
short form, 5, 784
show channel labels, 234
show measurements, 345, 370
SICL example in C, 897
SICL example in Visual Basic, 906
SICL examples, 897
sigma, mask test run, 413
signal type, 214
signed data, 624
simple command headers, 785
sine waveform demo signal, 222
sine waveform generator output, 659
single acquisition, 160
single frequency, frequency response
analysis, 275
single-ended probe heads, 211
single-ended signal type, 214
single-shot demo signal, 222
single-shot DUT, synchronizing with, 776
skew, 213, 703
skew reference waveform, 693
slope, 500, 587
slope (direction) of waveform, 724
slope not valid in TV trigger mode, 587
slope parameter for delay
measurement, 354
slope, setup and hold trigger, 603
slope, transition trigger, 610
smoothing acquisition type, 623
snapshot all measurement, 347
softkey menu timeout, 236
software version, 116
source, 371, 466, 488
source for function, 306, 307, 709
source for trigger, 588
source for TV trigger, 617
source input for FFT function, 265
source, automask, 396
source, mask test, 421
source, save reference waveform, 449
source, transition trigger, 611
source, waveform, 640
span, 289, 301
span of frequency on display, 266, 293
specify measurement, 371
SPI, 500
SPI clock timeout, 501
SPI decode bit order, 499
SPI decode word width, 512
SPI MISO data, 644
SPI trigger, 502, 508, 510
SPI trigger clock, 503
SPI trigger commands, 497
SPI trigger frame, 504
SPI trigger MISO data pattern, 507
SPI trigger MOSI data pattern, 509
SPI trigger type, 511
SPI trigger, MISO data source, 505
SPI trigger, MOSI data source, 506
SPI triggering, 452
square wave duty cycle, waveform
generator, 664
square waveform generator output, 659
SRE (Service Request Enable
Register), 126, 757
SRQ (Service Request interrupt), 144, 148
standard deviation measured on
waveform, 369
Standard Event Status Enable Register
(ESE), 112, 762
Standard Event Status Register (ESR), 114,
761
standard for video, 618
standard, LIN, 489
start acquisition, 129, 143, 158, 160
start and stop edges, 352
start cursor, 722
start measurement, 345
start print job, 319
start time, 595, 722
start time marker, 719
state memory, 124
state of instrument, 117, 555
status, 127, 161, 163
Status Byte Register (STB), 125, 127, 128,
755
status data structure clear, 111
status registers, 50
status reporting, 751
STB (Status Byte Register), 125, 127, 128,
755
step size for frequency span, 266, 293
stop,
143, 162
stop acquisition, 162
stop cursor, 723
stop displaying channel, 142
stop displaying math function, 142
stop displaying pod, 142
stop on mask test failure, 412
stop time, 595, 723
storage, 124
store instrument setup, 117, 124
store setup, 124
storing calibration information, 192
string variables, 48
string variables, reading multiple query
results into, 49
string variables, reading query results into
multiple, 49
string, quoted ASCII, 104
subsource, waveform source, 644
subsystem commands, 3, 787
subtract math function, 289, 301, 640
subtract math function as g(t) source, 297
sweep mode, trigger, 571, 582
sweep speed set to fast to measure fall
time, 357