User Manual

922 Keysight InfiniiVision 1000 X-Series Oscilloscopes Programmer's Guide
Index
example code, :SYSTem:SETup, 555
example code, :TIMebase:DELay, 740
example code, :TIMebase:MODE, 561
example code, :TIMebase:RANGe, 563
example code, :TIMebase:REFerence, 564
example code, :TRIGger:MODE, 580
example code, :TRIGger:SLOPe, 587
example code, :TRIGger:SOURce, 588
example code, :VIEW and :BLANk, 164
example code, :WAVeform, 640
example code, :WAVeform:DATA, 628
example code, :WAVeform:POINts, 632
example code, :WAVeform:PREamble, 636
example code,
:WAVeform:SEGMented, 183
example code, *RST, 123
example programs, 5, 791
examples on the website, 791
EXE (Execution Error) status bit, 112, 114
execution error detected in Standard Event
Status, 114
exponential notation, 103
external glitch trigger source, 596
external range, 255
external trigger, 248, 254, 588
EXTernal trigger commands, 247
external trigger input waveform, vertical
position, 253
external trigger input, display setting, 250
external trigger input, trigger level, 252
EXTernal trigger level, 585
external trigger probe attenuation
factor, 254
external trigger probe sensing, 708
EXTernal trigger source, 588
external trigger units, 256
external waveform label, 251
F
failed waveforms in mask test, 400
failure, self test, 130
fall time measurement, 345, 357
Fast Fourier Transform (FFT)
functions, 259, 266, 268, 289, 291,
293, 295, 301, 307, 709
FF values in waveform data, 628
FFT (Fast Fourier Transform) functions, 259,
266, 268, 289, 291, 293, 295, 301,
307, 709
FFT (Fast Fourier Transform) operation, 640
FFT commands, 257
FFT function display, 260
FFT function, source input, 265
FFT vertical units, 267, 294
FFTPhase (Fast Fourier Transform)
functions, 301
fifty ohm impedance, disable setting, 547
filename for hardcopy, 712
filename for recall, 425, 658
filename for save, 434
filter for frequency reject, 586
filter for high frequency reject, 575
filter for noise reject, 581
filter used to limit bandwidth, 203, 249
filters to Fast Fourier Transforms, 268, 295
fine horizontal adjustment (vernier), 566
fine vertical adjustment (vernier), 219
finish pending device operations, 118
first point displayed, 650
FLATtop window for amplitude
measurements, 268, 295
FM burst demo signal, 222
FM modulation type, waveform
generator, 675
force trigger, 574
format, 630, 635
format for block data, 117
format for hardcopy, 711
format for image, 437
format for waveform data, 445
FormattedIO488 object, 43
formfeed for hardcopy, 310, 314
formulas for data conversion, 623
frame, 504
frame counters (CAN), error, 458
frame counters (CAN), overload, 459
frame counters (CAN), reset, 460
frame counters (CAN), total, 461
frame counters (UART), error, 518
frame counters (UART), reset, 519
frame counters (UART), Rx frames, 520
frame counters (UART), Tx frames, 521
framing, 502
FRANalysis commands, 271
frequency deviation, waveform generator FM
modulation, 667
frequency measurement, 41, 345, 358
frequency measurements with X
cursors, 330
frequency resolution, 268, 295
frequency response analysis, data, 273
frequency response analysis, enable, 274
frequency response analysis, run, 280
frequency response analysis, single
frequency, 276
frequency response analysis, sweep start
frequency, 277
frequency response analysis, sweep stop
frequency, 278
frequency span of display, 266, 293
frequency versus dB, 289
front panel mode, 582
front panel Single key, 160
front panel Stop key, 162
front-panel lock, 540
FSK modulation type, waveform
generator, 675
FSK rate, waveform generator
modulation, 670
full-scale horizontal time, 563, 568
full-scale vertical axis defined, 262, 303
function, 164, 259, 266, 268, 290, 291,
293, 295, 300, 301, 303, 304, 305,
709, 710
FUNCtion commands, 287
function memory, 161
function turned on or off, 710
function, demo signal, 222
function, waveform generator, 659
functions, 640
G
g(t) source, first input channel, 298
g(t) source, math operation, 297
g(t) source, second input channel, 299
gain data, including in FRA results, 283
general SBUS<n> commands, 453
general trigger commands, 573
glitch demo signal, 222
glitch duration, 595
glitch qualifier, 594
glitch source, 596
GLITch trigger commands, 589
glitch trigger duration, 590
glitch trigger polarity, 593
glitch trigger source, 590
graticule area for hardcopy print, 311
graticule colors, invert for hardcopy, 315,
714
graticule colors, invert for image, 438
grayscale palette for hardcopy, 317
grayscale palette for image, 439
grayscaling on hardcopy, 713
greater than qualifier, 594
greater than time, 590, 595
H
HANNing window for frequency
resolution, 268, 295
hardcopy, 157, 310
HARDcopy commands, 309
hardcopy factors, 313, 436
hardcopy filename, 712
hardcopy format, 711
hardcopy formfeed, 314
hardcopy grayscale, 713
hardcopy invert graticule colors, 315, 714
hardcopy layout, 316
hardcopy palette, 317
hardcopy print, area, 311
hardcopy printer driver, 715
HARMonics demo signal, 222
head type, probe, 211
header, 783
high resolution acquisition type, 623
high trigger level, 578
high-frequency reject filter, 575, 586
high-level voltage, waveform
generator, 683