User Manual

Index
Keysight InfiniiVision 1000 X-Series Oscilloscopes Programmer's Guide 921
cursor mode, 324
cursor position, 325, 327, 329, 332, 334
cursor readout, 718, 722, 723
cursor reset conditions, 121, 544
cursor source, 326, 328
cursor time, 718, 722, 723
cursor units, X, 330, 331
cursor units, Y, 335, 336
cursors track measurements, 370
cursors, how autoscale affects, 137
cursors, X1, X2, Y1, Y2, 322
cycle measured, 356, 359
cycle time, 363
D
data, 476, 478, 628
data (waveform) maximum length, 447
data 2, 479
data acquisition types, 621
data conversion, 623
data format for transfer, 624
data output order, 626
data pattern length, 470, 495
data pattern, CAN trigger, 469
data point index, 650
data points, 180
data record, measurement, 633
data record, raw acquisition, 633
data required to fill time buckets, 177
data source, setup and hold trigger, 605
data structures, status reporting, 753
data, saving and recalling, 226
date, calibration, 191
date, system, 537
dB versus frequency, 289
DC coupling for edge trigger, 584
DC input coupling for specified
channel, 204
DC RMS measured on waveform, 383
DC waveform generator output, 660
DDE (Device Dependent Error) status
bit, 112, 114
decision chart, status reporting, 770
default conditions, 121, 544
define channel labels, 208
define glitch trigger, 594
define measurement, 352
define measurement source, 371
define trigger, 595
defined as, 103
definite-length block query response, 48
definite-length block response data, 104
delay measured to calculate phase, 364
delay measurement, 352
delay measurements, 373
delay parameters for measurement, 354
delay, how autoscale affects, 137
delayed time base, 561
delayed window horizontal scale, 569
delete mask, 405
delta time, 718
delta voltage measurement,
726
delta X cursor, 322
delta Y cursor, 322
demo, 221
DEMO commands, 221
demo signal, 222
demo signal function, 222
demo signals output control, 224
destination, remote command logging, 549
detecting probe types, 705, 708
device-defined error queue clear, 111
differences from 2000 X-Series oscilloscope
commands, 28
differential probe heads, 211
differential signal type, 214
digital channel source for glitch
trigger, 596
digitize channels, 143
DIGitize command, 40, 45, 622
digits, 104
disable front panel, 540
disable function, 710
disabling calibration, 194
disabling channel display, 205
disabling status register bits, 112, 125
discontinued and obsolete commands, 697
display annotation, 227
display annotation background, 228
display annotation color, 229
display annotation text, 230
display channel labels, 234
display clear, 231
DISPlay commands, 225
display commands introduction, 226
display connect, 706
display date, 537
display factors scaling, 210
display for channels, 205
display frequency span, 266, 293
display measurements, 345, 370
display persistence, 237
display reference, 562, 564
display reference waveforms, 690
display reset conditions, 122
, 545
display serial number, 159
display vectors, 238
display, FFT function, 260
display, oscilloscope, 237, 290, 538
display, serial decode bus, 454
displaying a baseline, 582
displaying unsynchronized signal, 582
divide math function, 301
driver, printer, 715
duplicate mnemonics, 787
duration for glitch trigger, 590, 591, 595
duration triggering, 572
duty cycle measurement, 41, 345, 356,
359
DVM commands, 239
DVM displayed value, 241
DVM enable/disable, 242
DVM frequency value, 243
DVM input source, 245
DVM mode, 244
E
edge coupling, 584
edge fall time, 357
edge parameter for delay
measurement, 354
edge preshoot measured, 365
edge rise time, 368
edge slope, 587
edge source, 588
EDGE trigger commands, 583
edge triggering, 571
edges in measurement, 352
elapsed time in mask test, 402
ellipsis, 104
enable channel labels, 234
enabling calibration, 194
enabling channel display, 205
enabling status register bits, 112, 125
end of string (EOS) terminator, 784
end of text (EOT) terminator, 784
end or identify (EOI), 784
EOI (end or identify), 784
EOS (end of string) terminator, 784
EOT (end of text) terminator, 784
erase data, 231
erase measurements, 717
erase screen, 707
error frame count (CAN), 458
error frame count (UART), 518
error messages, 539, 743
error number, 539
error queue, 539, 763
error, measurement, 345
ESB (Event Status Bit), 126, 128
ESE (Standard Event Status Enable
Register), 112, 762
ESR (Standard Event Status Register), 114,
761
event status conditions occurred, 128
Event Status Enable Register (ESE), 112,
762
Event Status Register (ESR), 114, 163, 761
example code, :ACQuire:COMPlete, 177
example code, :ACQuire:SEGMented, 183
example code, :ACQuire:TYPE, 188
example code, :AUToscale,
138
example code, :CHANnel<n>:LABel, 208
example code, :CHANnel<n>:PROBe, 210
example code, :CHANnel<n>:RANGe, 216
example code, :DIGitize, 143
example code, :DISPlay:DATA, 232
example code, :DISPlay:LABel, 234
example code, :MEASure:PERiod, 371
example code, :MEASure:TEDGe, 374
example code, :MTESt, 391
example code, :RUN/:STOP, 158