User guide

7-19
Chapter 7 RS-232C
7
Serial Commands to check the LS Settings
The following section provides information on command formats used to check setting
details.
Code
Command Response
S C , H E , a cr
S C , A R , a cr
S C , S E , a cr
S C , A T , a cr
S C , L E , a cr
S C , C A , h cr
S C , A V , h cr
S C , M E , h cr
S C , T M , h cr
S C , O F , h cr
S C , A U , h cr
S C , A O , h cr
S C , U P , h cr
S C , S D , h cr
S C , L W , h cr
S C , H H , h cr
S C , H I , h cr
S C , L O , h cr
S C , L L , h cr
S C , J O , h cr
S C , E H , h cr
S C , E L , h cr
S C , C A , h , i i cr
S C , A V , h , j
cr
S C , M E , h k ,
S C , T M , h l l l l ,
S C , O F , h m
n
m m m m m m m cr ,
S C , U P , h m m m m m m m m cr ,
S C , S D , h m m m m m m m m cr ,
S C , L W , h m m m m m m m m cr ,
S C , H H , h m m m m m m m m cr ,
S C , H I , h m m m m m m m m cr ,
S C , L O , h m m m m m m m m cr ,
S C , L L , h m m m m m m m m cr ,
S C , E H , h m m m m m m m m cr ,
S C , E L , h m m m m m m m m cr ,
S C , C L , a cr
S C , C L , a m m m m m m m m m m m m m m m m ,,
m m m m m m m m m m m m m m m m cr ,
,
S C , J O , h w w cr ,
S C , A U , h ,
S C , A O , h m m m m m m m m , m m m m m m m m cr ,
S C , H E , a , b cr
S C , A R , a , c cr
S C , S E , a , d d d d e , d d d d e cr
S C , A T , a , f f f cr
S C , L E , a , g g cr
Head
(Page 7-13)
Area
(Page 7-13)
SEG edge number
(Page 7-13)
Area check
(Page 7-14)
Level
(Page 7-14)
Calculation
(Page 7-14)
Average
(Page 7-14)
Measuring mode
(Page 7-15)
Offset
(Page 7-15)
Analog Reference value
(Page 7-15)
Threshold
(Page 7-16)
Reference
value
(Page 7-16)
Logic calibration
(Page 7-18)
STANDARD
LOWER
HH
HI
LO
LL
Hold ON/OFF
(Page 7-18)
HOLD-H
HOLD-L
Self-timing
(Page 7-15)
j cr
crk
n cr
a : Area setting number
b : Head number
c : Area
dddd : Edge number
e : Edge mode
fff : Number of edges
gg : Threshold
h : Output setting number
ii : Calculation
jj : Averaging number
kk : Measuring mode
llll : Self-timing period
mmmmmmmm : Numeric value
nn : Analog scale
w : ON/OFF
Calibration setting
Tolerance setting Output setting
Area setting
Threshold
(Page 7-17)
UPPER
❈ The above formats are examples with the Cr character used for delimiters.
If the KV-10/80 series is used (i.e., PLC is set as a D-MODE environment setting),
use the STX+ETX characters instead of Cr. (See page 7-6)
❈ Refer to Outline of Command Formats on page 7-6 for commands in detail. When
the response for the setting change command is received by the LS-7000 Series,
the LS-7000 Series will return detailed data on the current settings in the LS-7000.