User Manual

ManualsBrandsKEYENCE ManualsSensorsLR-TB2000 Series

All-Purpose Laser Sensor

LR-TB2000 Series

Instruction Manual

Read this manual before using the product in order to achieve maximum performance.

Keep this manual in a safe place after reading it so that it can be used at any time.

The following symbols alert you to important messages. Be sure to read these

messages carefully.

1 Introduction

Safety Information for LR-TB Series

Safety Precautions on Laser Product

This product uses a semiconductor laser as its light source.

* The laser classification for FDA (CDRH) is implemented based on IEC60825-1 in

accordance with the requirements of Laser Notice No.50.

 Laser warning and explanation labels

z Laser warning and explanation labels

• Attached to the cable

• Included with the product

* For a Class 2 laser product, select from the warning and explanation labels included

in the package the appropriate warning and explanation label according to the coun-

try and region where the Class 2 laser product will be used. Then, affix the warning

and explanation label over top of the existing warning and explanation label on the

product.

Precautions on Regulations and Standards

 CSA Certificate

LR-TB series complies with the following CSA and UL standards and has been certified by

CSA (Class 2252 06 / Class 2252 86).

• Applicable standard: CAN/CSA C22.2 No.61010-1

UL61010-1

• Use the following power supply.

CSA/UL certified power supply that provides Class 2 output as defined in the CEC

(Canadian Electrical Code) and NEC (National Electrical Code), or CSA/UL certified power

supply that has been evaluated as a Limited Power Source as defined in CAN/ CSA-C22.2

No. 60950-1/UL60950-1

• Use this product at the altitude of 2000 m or less.

• Use this product at the level of overvoltage category I.

• Use this product at pollution degree 3.

• Indoor use only.

 CE Marking

Keyence Corporation has confirmed that this product complies with the essential

requirements of the applicable EC Directive, based on the following specifications.

Be sure to consider the following specifications when using this product in a member state

of the European Union.

z EMC Directive (2004/108/EC)

• Applicable standard EMI : EN60947-5-2, Class A

EMS : EN60947-5-2

z Low-voltage Directive (2006/95/EC)

• Applicable standard: EN61010-1, EN60825-1

• Use the power supply that has been evaluated as a Limited Power Source as defined in

IEC60950-1/EN60950-1.

• Use this product at the altitude of 2000 m or less.

• Use this product at the level of overvoltage category I.

• Use this product at pollution degree 3.

• Indoor use only

Remarks: These specifications do not give any guarantee that the end-product with this

product incorporated complies with the essential requirements of the EMC

Directive.

The manufacturer of the end-product is solely responsible for the compliance of

the end-product itself according to the EMC Directive.

It indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

It indicates a situation which, if not avoided, could result in product

damage as well as property damage.

• This product is only intended to detect object(s). Do not use this

product for the purpose to protect a human body or part of a human

body.

• This product is not intended for use as an explosion-proof product.

Do not use this product in a hazardous location and/or potentially

explosive atmosphere.

• This product uses DC power. The product may explode or burn if an

AC voltage is applied.

• Do not wire the cable along with power lines or high-tension lines,

as the sensor may malfunction or be damaged due to noise.

• When using a commercially available switching regulator, ground

the frame ground terminal and ground terminal.

• Do not use this product outdoors or in a location in which its

light-receiving surface will come in direct contact with stray ambient

light.

• Use of controls or adjustments or performance of procedures other

than those specified herein may result in hazardous radiation

exposure.

• Follow the instructions mentioned in this manual. Otherwise, injury

to the human body (eyes and skin) may result.

• Laser emission from this product is not automatically stopped when

it is disassembled. Do not disassemble this product.

• Precautions on Class 2 Laser Product

- Do not stare into the direct or specularly reflected beam.

- Do not direct the beam at people or into areas where people

might be present.

- Be careful of the path of the laser beam.

If there is a possibility that the operator may be exposed to the

specular or diffuse reflections, block the beam by installing a

protective enclosure.

- Install this product so that the path of the laser beam is not as the

same height as that of human eye.

• Precautions on Class 1 Laser Product

- Do not stare into the direct or specularly reflected beam.

Item Description

Model

LR-TB2000

LR-TB2000CL

LR-TB2000C

Wavelength 660 nm

Pulse width 4.3 ns

FDA(CDRH)

Part1040.10

Laser class* Class 2 laser product Class 1 laser product

Output 1.0 mW 390 μW

JIS C 6802/

IEC 60825-1

Laser class Class 2 laser product Class 1 laser product

Output 1.0 mW 390 μW

WARNING

NOTICE

WARNING

NOTICE

WARNING

1567

1234

XX-XXXX

DISP

MODE

Laser emission

point

Laser warning and

explanation label

Class 2 (English) Class 1

Class 2 (included with the product in each language)

96M12738

Summary of content (12 pages)

PAGE 1
Laser warning and explanation labels 34 15 12 D IS P M O D E 2 1 67 X X -X X X X 96M12738 All-Purpose Laser Sensor LR-TB2000 Series Laser emission point Laser warning and explanation label z Laser warning and explanation labels Instruction Manual • Read this manual before using the product in order to achieve maximum performance. Keep this manual in a safe place after reading it so that it can be used at any time.
PAGE 2
Package Contents Part Functions • Main unit • Instruction manual • Laser warning and explanation labels (LR-TB2000/TB2000C only) Indicator Output 1 ON : Orange* Output 1 OFF : Green* Error : Flashing red * The indicator flashes when two conditions below are met; • Stability output turns ON ( page 9). • Output 1 turns OFF when output logic is N.O. or turns ON when output logic is N.C.
PAGE 3
Initial Settings 3-1. I/O Selection When you turn on the LR-TB Series for the first time after you purchase it or when you have initialized the LR-TB Series, the following initial settings must be configured. Select from the following table the functions assigned to the I/O wires (black and white).
PAGE 4
Detection Mode 4-2. Distance Mode (BGS) The LR-TB Series has four output modes and three detection modes. Output Mode ( page 9) Operation • In this mode, the distance from the sensor is displayed. Detection Mode 4-1. DATUM mode (FGS) Standard (default value) [Standard] 2000 4-2. Distance mode (BGS) Window [Window] 0 A 4-3.
PAGE 5
z Full auto calibration Use this function when the movement of detected objects cannot be stopped. 4-3. Window Mode Operation 1 • In this mode, the distance from the sensor is displayed. • You can assign setting values to the upper and lower limits. 2000 XX-XXXX 1 2 1567 1234 DISP FAR NEAR 0 MODE Press and hold the set button for 3 seconds or more. XX-XXXX 1 2 2 1567 1234 DISP MODE The object is detected while the button is pressed.
PAGE 6
When [Out2] mode is set to [Standard] or [Window] z 1-point calibration Use this function when you cannot move detected objects away from the center of the detection range. Press the [DISP/S] or the [MODE/T] button (for 1 second or less). XX-XXXX 1 2 1 1567 1234 DISP MODE XX-XXXX 1 2 1567 1234 DISP MODE Press and hold the set button for 3 seconds or more.
PAGE 7
5 Useful Functions Switching between Display Screens You can select between four different displays. Key Lock Display screen To require a password to release the key lock, see XX-XXXX 1 2 1567 " 6-11. Password" (page 10). Use the I/O selection to change what is displayed here. " 3-1. I/O Selection" (page 3).
PAGE 8
6 Detailed Settings The values shown on the display screen are the initial values. 1 2 1567 1234 3-1. I/O Selection ( page 3) 3 seconds A Out1+Out2 B Input+Out1 You can complete settings by holding down the button. Menu 6-1. Response Time ( page 9) 1000 ms 100 ms 25 ms 10 ms 1 ms *1 Response Time 25 ms Hysteresis 6-5. Hysteresis ( page 10) Standard Custom Standard Custom Hys. Value 6-2. Output 1 Logic ( page 9) Output1 Logic 6-3. Output 1 Mode ( page 9) Output1 Mode 6-6.
PAGE 9
XX-XXXX MODE DISP 1 2 1234 Longer response times lead to more stable detection. 1567 Example) Chart during DATUM mode 6-1.
PAGE 10
6-5. Hysteresis 6-10. Interference Prevention Hysteresis is the difference between the value at which the output turns ON and the value at which the output turns OFF. With the LR-TB Series, you can prevent the effect of mutual interference by changing the laser emission channel. If you are using multiple LR-TB Series units in close proximity to each other, set each one to have a different laser emission channel. NEAR Setting value 6-11.
PAGE 11
PAGE 12
WARRANTIES AND DISCLAIMERS (1) KEYENCE warrants the Products to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment. If any models or samples were shown to Buyer, such models or samples were used merely to illustrate the general type and quality of the Products and not to represent that the Products would necessarily conform to said models or samples.