User guide
Table Of Contents
- Introduction
- Safety Information for IV Series
- Important Instructions
- Precautions on Regulations and Standards
- Version of the IV Series
- Structure of This Manual
- Contents
- Chapter 1 Getting Started
- Chapter 2 Installation and Connection
- Mounting the Sensor
- Mounting the Monitor
- Cables
- Chapter 3 Basic Operation
- Overview of Screen and Operation
- Basic Operation Flow
- Operation when the Power is Turned on
- Setting to the Factory Default
- Basic Operation for the Monitor
- Chapter 4 Settings Navigator (Setting the Judgment Condition)
- Settings Navigator
- Basic Operation of the Settings Navigator
- 1. Image Optimization (Clearly Image a Target)
- 2. Master Registration (Registering an Image as a Reference for Judgment)
- 3. Tool Settings (Setting the Judgment Method for Targets)
- 4. Output Assignment (Setting Details of Outputting to Output Line)
- Display Method of Extended Functions Menus
- Chapter 5 Operating/Adjusting
- Starting an Operation
- Overview of the Operation Screen
- Names and Functions of the Operation Screen
- Adjusting Thresholds for Judgment
- Tool Auto Tuning (Automatically Adjusting the Judgment Condition)
- Operation flow for the Tool Auto Tuning
- Starting and finishing the Tool Auto Tuning
- Registering the OK/NG images to be used for the Tool Auto Tuning
- Confirming or deleting the images registered for the Tool Auto Tuning
- Tool Auto Tuning by the previous registration information
- Tool Auto Tuning by the registration information file
- Stabilizing the Judgment Process
- Stabilizing the judgment process by taking a clear image of the target
- Imaging the target widely
- Correcting the distorted images due to the installation
- Achieving adequate image brightness
- Achieving good focus
- Reducing the image blur
- Reducing the shininess of the glossy or metal surface
- Adjusting the color tint (for color type only)
- Reducing the effect of illumination variation
- Stabilizing by correcting the misaligned target position
- Stabilizing the position adjustment
- Stabilizing the Outline tool
- ■Basic adjustments
- ■If the outline cannot be detected when the target becomes out of position
- ■If the detection becomes unstable due to the effect of the unwanted outline other than the target
- ■If the target tilts and the outline cannot be detected
- ■If the match rate difference between the high and low-quality-targets is small
- ■If the outline of the target cannot be detected
- Stabilizing the Color Area/Area tool
- Stabilizing the judgment process by taking a clear image of the target
- Shortening the Processing Time
- Chapter 6 Useful Features/Various Functions
- List of the Useful Features
- Displaying the Sensor Setup Menu Screen
- Changeover for a Target (Program Functions)
- Sensor Image History (Confirming the Images whose Status Result is NG)
- Saving the Sensor Settings and Images to a USB Memory
- Setting the Extended Functions of the Sensor
- Setting the Advanced Monitor Information
- Chapter 7 Controlling with Input/Output Line
- Chapter 8 Specifications
- Appendices
- Status Table
- Matching Rate of the Outline Tool and Position Adjustment Tool
- Settings List
- Troubleshooting
- Error Messages
- Remedy when the Monitor cannot be Connected with the Sensor
- Initializing the Network Settings (IP Reset Switch)
- Maintenance
- Index
A-3
- IV Series User's Manual (Monitor) -
A
Status Table
Status table
Status
Monitor
screen
type
Sensor operation indicator light
Input Output
PWR/ERR OUT TRIG
External
trigger
Switch
programs
External
master image
registration
Clear
Error
BUSY
Total Status / Total status NG /
Each tool / Each logic /
Pos.Adj.
*1
RUN Error
Running
*2
Waiting for a trigger
RUN
Lighting
(green)
*3
OFF
Í
OFF
*4
ON OFF
Judgment processing *5
*6
*7 *8
ON
Switching programs
*9 OFF
*10 *11
*12
Registering the external master image
*11 *10
Setting
Limit Adjustment TEST
Blink
(green)
OFF *5
Í Í Í
Same
as while
running
OFF
OFF
OFF
Trigger Options, Master Registration, etc.
LIVE
Focus adjustment (MF) OFF *14 OFF
Automatically adjusting the brightness
Automatically adjusting the focus (AF)
Blink
(green)
OFF
*13
Í
*13
Setup Adjustment
-
*15 OFF
I/O Monitor
OFF
*16 ← ← ← ← ← ←
Others
Í Í Í Í
OFF OFF OFF
Error
Trigger error
Running RUN
Blink (red) Same as normal
Same as normal
Same as normal
ON
Setting LIVE
External master registration error
-System error
Lighting
(red)
OFF OFF
Í Í Í Í
OFF OFF
OFF
Startup memory readout error *17 *17 *17
*6 Disregards the input. A trigger error occurs.
*7 Stops the judgment process and switches over.
*8 Stops the judgment process and registers the previously taken image as a master image.
*9 Turns off the light before the process is completed. Until the light turns off, the previous status result
will be displayed.
*10 After the current process is completed, generates the new input.
*11 Do not use. The processing order becomes indeterminate.
*12 Turns OFF before the process is completed. Outputs the previous status result until this turns OFF.
*13 The internal trigger is issued automatically and the image will be updated. The Busy output operates.
*14 The ashing cycle of the orange light changes by linking to the focus indicator. The STATUS indicator
light operates in the same way.
*15 The internal trigger is issued automatically and the image is updated.
*16 While the I/O monitor function is used, only the operation of the I/O lines is conrmed. The assigned
functions will not operate.
*17 The NPN open collector output turns OFF regardless of the output settings (N.O./N.C.) and the
polarity (NPN/PNP) settings.
Additionally, refer to “Chapter 7 Controlling with Input/Output Line” (Page 7-1).