User guide
Table Of Contents
- Introduction
- Safety Information for IV Series
- Important Instructions
- Precautions on Regulations and Standards
- Version of the IV Series
- Structure of This Manual
- Contents
- Chapter 1 Getting Started
- Chapter 2 Installation and Connection
- Mounting the Sensor
- Mounting the Monitor
- Cables
- Chapter 3 Basic Operation
- Overview of Screen and Operation
- Basic Operation Flow
- Operation when the Power is Turned on
- Setting to the Factory Default
- Basic Operation for the Monitor
- Chapter 4 Settings Navigator (Setting the Judgment Condition)
- Settings Navigator
- Basic Operation of the Settings Navigator
- 1. Image Optimization (Clearly Image a Target)
- 2. Master Registration (Registering an Image as a Reference for Judgment)
- 3. Tool Settings (Setting the Judgment Method for Targets)
- 4. Output Assignment (Setting Details of Outputting to Output Line)
- Display Method of Extended Functions Menus
- Chapter 5 Operating/Adjusting
- Starting an Operation
- Overview of the Operation Screen
- Names and Functions of the Operation Screen
- Adjusting Thresholds for Judgment
- Tool Auto Tuning (Automatically Adjusting the Judgment Condition)
- Operation flow for the Tool Auto Tuning
- Starting and finishing the Tool Auto Tuning
- Registering the OK/NG images to be used for the Tool Auto Tuning
- Confirming or deleting the images registered for the Tool Auto Tuning
- Tool Auto Tuning by the previous registration information
- Tool Auto Tuning by the registration information file
- Stabilizing the Judgment Process
- Stabilizing the judgment process by taking a clear image of the target
- Imaging the target widely
- Correcting the distorted images due to the installation
- Achieving adequate image brightness
- Achieving good focus
- Reducing the image blur
- Reducing the shininess of the glossy or metal surface
- Adjusting the color tint (for color type only)
- Reducing the effect of illumination variation
- Stabilizing by correcting the misaligned target position
- Stabilizing the position adjustment
- Stabilizing the Outline tool
- ■Basic adjustments
- ■If the outline cannot be detected when the target becomes out of position
- ■If the detection becomes unstable due to the effect of the unwanted outline other than the target
- ■If the target tilts and the outline cannot be detected
- ■If the match rate difference between the high and low-quality-targets is small
- ■If the outline of the target cannot be detected
- Stabilizing the Color Area/Area tool
- Stabilizing the judgment process by taking a clear image of the target
- Shortening the Processing Time
- Chapter 6 Useful Features/Various Functions
- List of the Useful Features
- Displaying the Sensor Setup Menu Screen
- Changeover for a Target (Program Functions)
- Sensor Image History (Confirming the Images whose Status Result is NG)
- Saving the Sensor Settings and Images to a USB Memory
- Setting the Extended Functions of the Sensor
- Setting the Advanced Monitor Information
- Chapter 7 Controlling with Input/Output Line
- Chapter 8 Specifications
- Appendices
- Status Table
- Matching Rate of the Outline Tool and Position Adjustment Tool
- Settings List
- Troubleshooting
- Error Messages
- Remedy when the Monitor cannot be Connected with the Sensor
- Initializing the Network Settings (IP Reset Switch)
- Maintenance
- Index
6-5
- IV Series User's Manual (Monitor) -
List of the Useful Features
Items Things you want to do Useful functions Description
Reference
page
Settings
Conrm/edit the settings or
conrm the operation results
without connecting to the
sensor.
Simulator functions
of IV-Navigator
The settings can be conrmed
or edited by using a batch
backup les (*.iva). Also,
the operation results can be
simulated.
1-5
Back up the settings to the
USB memory
Batch Backup
The settings for the sensor
can be read and saved into
the USB memory.
6-19
Copy the settings to multiple
sensors
Transfer Program
Settings
The batch backup data stored
into the USB memory can be
transferred to another sensor.
6-21
Copy the settings and use
the settings to set another
product
Program function
The settings of a set program
number which has been set
can be copied to another
program number.
6-12
Conrm the settings of the
sensor with the list.
Export functions of
IV-Navigator
The list of settings can be
conrmed with Microsoft Excel
etc.
1-5
Initialize the settings of the
sensor
Initialize Sensor
The settings can be initialized
to the factory default.
6-44
Initialize the settings of the
monitor
Initialize Monitor
The settings can be initialized
to the factory default.
6-53
Conrm the version of the
sensor
Sensor Information
The version for the model or
the operation software can be
conrmed.
6-43
Conrm the version of the
monitor
Monitor Information
The version for the model or
the operation software can be
conrmed.
6-53
6
Useful Features/Various Functions