96M1068 Wireless LAN Access Point NE-W01E Instruction Manual
Preface This manual describes how to install and connect the Wireless LAN Access Point NEW01E. To ensure full use of the Wireless LAN Access Point NE-W01E, be sure to thoroughly read this manual, and fully understand the functions of the NE-W01E before use. Store this manual in a safe place so that you can retrieve it whenever necessary. ■ Symbols This manual uses the following symbols to alert you to important information. DANGER Failure to follow these instructions may lead to death or serious injury.
■ How This Manual Is Organized This manual briefly describes this product and describes the procedure from installation through to connection, Proceed with work by following the procedure illustrated below. Dotted lines indicate parts described in this manual. Before you start to use your NE-W01E Safety Precautions (page 2) Operating Environment (page 7) Check the functions of the NE-W01E.
Safety Precautions ■ General Precautions • At startup and during operation, be sure to monitor the functions and performance of the NE-W01E. • We recommend that you take substantial safety measures to avoid any damage in the event that a problem occurs. • Do not modify the NE-W01E or use it in any way other than described in the specifications. The functions and performance of products used or modified in this way cannot be assured.
Use cellphones, PHS, TVs or radios as far away as possible from the NE-W01E. Noise is sometimes generated in voice or video images due to the influence of radio waves generated by wireless LAN products. DANGER • Do not lay cables during lightning. Lightning may cause electric shock. • Do not build a network using this device that may adversely affect human life or damage equipment. CAUTION • Do not touch the Ethernet ports with a pen, screwdriver or other finetipped object.
■ Precautions for CE Marking The NE-W01E is subject to the R&TTE Directive. Keyence Corporation has evaluated compliance with the requirements of the R&TTE Directive when the following conditions were satisfied, and has confirmed that the NE-W01E satisfies those requirements.
■ Precautions for UL Certificate The NE-W01E complies with the UL standard and has UL/C-UL certificate under the following details. • Applicable standard UL508 Industrial Control Equipment CAN/CSA C22.2 No. 14-M95 Industrial Control Equipment • UL File No.
■ Precautions for FCC The NE-W01E falls under the category of intentional radiowave-emitting devices stipulated in FCC Part 15 subpart C. Keyence Corporation has evaluated compliance with the requirements of FCC Part 15 subpart C, and has confirmed that the NE-W01E satisfies those requirements. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Operating Environment ■ Installation location Do not install the NE-W01E in the following locations.
■ Installation location precautions Pay attention to the following points when installing the NE-W01E. • Do not install the NE-W01E in a location where the ambient temperature exceeds the 0 to +50°C range or the ambient humidity exceeds the 35 to 80%RH range. • If the ambient temperature exceeds the above range, install a forced air cooling fan or air conditioner to keep the ambient temperature within this range.
Features and Functions of the NE-W01E Wireless LAN Access Point NE-W01E is an access point for wireless LAN communications that is compliant with IEEE802.11b. ■ IEEE802.11b compliant NE-W01E is compliant with the IEEE802.11b standard , and is capable of highspeed wireless communications of 11 Mbps (logical value). ■ Wiring by cables is no longer required, allowing the configuration of a wireless network. Wiring by conventional network cables is no longer required.
Examples of Networks Built Using NEW01E A wireless LAN network can be built by combining NE-W01E with Wireless LAN Station NE-W11E. Wireless LANs operate in two communications modes: infrastructure mode and ad-hoc mode. When NE-W01E is combined with these products to build a network, configure the network in the infrastructure mode. Note: The NE-W01E cannot be used in networks configured in the ad-hoc mode.
● Example 2 Headquarters network, Internet, etc. Office, etc. Factory, production site, etc. NE-W01E Router/modem, etc.
Checking the Contents of the Package The package contains the following items. Before you start using the NE-W01E, make sure that the package contains everything that it is supposed to contain. NE-W01E body Antennas (2 pcs) Magnets Magnet mounting screws (2 pcs, mounted on body) (2 pcs, mounted on body) Wall-mounting screws (3 pcs) Wireless LAN Access Point NE-W01E Instruction Manual Rubber caps (2 pces) Instruction Manual (this manual) Every effort has been made preparing this package.
Names of Parts ■ Front view (1) ■ Rear view (1) (6) (8) (8) (7) (8) POWER WIRELESS ETHERNET (8) (2) (3) (4) (5) (6) ■ Side view ■ Bottom view (11) (12) (9) (10) 13
Description Name Antenna Antenna (2 pcs) (2) POWER LED (green) This LED lights (green) when the unit is energized. (3) WIRELESS LED (green) This LED indicates the state of wireless LAN communications. Lit: The wireless LAN link is established. Blinking: Communications is in progress. Out: The wireless LAN link is not established. (4) ETHERNET LED (green) This LED indicates the state of the Ethernet port. Lit: The link with the destination device is established.
Installing the NE-W01E ■ Installation location • Read "Safety Precautions" ( page 2) in this manual, and check the precautions when using the NE-W01E. • Read "Operating Environment" ( page 7) in this manual, and check the precautions regarding the installation location. The NE-W01E uses radio waves. So, sometimes normal communications is no longer possible in some operating environments.
● Distance between surrounding areas Be sure to allow at least 30 mm of space between the NE-W01E and other devices or surrounding walls when installing the NE-W01E. ■ Attaching the antennas 1 Attach the rubber caps onto the antennas (provided). (1) Turn antenna in direction of arrow to fasten. Rubber cap Turn until cap fits flush. (2) Insert rubber cap onto antenna down to its base. 2 Adjust the orientation of the antennas.
■ Installing the NE-W01E The NE-W01E can be installed on flat surfaces such as desktops, on vertical surfaces such as walls, and on ceilings. Select the mounting method according to the environment where you will be using NE-W01E: • Magnet mount • Screw mount • Wall mount ● Magnet mount Mount the NE-W01E by the magnets on the back of the NE-W01E.
2 Check the positions of the four screw holes, and drill holes for screw fastening at the location (panel, etc.) where the NE-W01E body is to be installed. (Installation location) 124 ø3.5 +0.5 0 70 Unit: mm 3 Align the position of the screw-fastening holes with the rear of the NEW01E body, and fasten the four locations with the screws. Tighten the screws with a torque of 0.4 Nm {4 kgf•cm}. (1) Fasten NE-W01E with screws at four locations from rear of body.
● Wall mount 1 Remove the magnets on the rear of the NE-W01E body. Slide the wallmounting fixture downwards. (2) Remove magnets from body. (1) Unscrew magnets. (3) Slide wall-mounting fixture downwards. Note: When re-attaching the magnets after you have removed them from the NEW01E body, tighten the screws that hold the magnets in place with a torque of 0.4 Nm {4 kgf•cm}. 2 Attach two of the wall-mounting screws (provided) at the location (wall, etc.) where the NE-W01E is to be installed.
3 Align and hook the screw holes on the rear of the NE-W01E body onto the screws on the wall. Slide the body slightly to the right to prevent it from falling from the wall. (1) Hook screw holes on rear of NE-W01E body onto wall-mounting screws, and slide body slightly to right. (view of NE-W01E from side) 4 Attach the remaining wall-mounting screws in the holes of the wallmounting fixture, and fasten the body firmly against the wall. (1) Attach wall-mounting screws to fasten body against wall.
Power Connection and Ground ■ How to open the power supply terminal block cover The power terminal block on the NE-W01E is protected by a cover. When connecting the power supply, open this cover by the following procedure. 1 2 Use a screwdriver to loosen the two screws fastening the cover. Slide the cover in the direction of the arrow, and open the cover upwards as it is. (2) Slide in the direction of the arrow (3) Open upwards. (1) Loosen this screw.
■ When using crimped terminals Use crimped terminals that conform to the following shapes and dimension. a NE-W01E a: 8 mm max. a ■ Wiring Connect the 100 to 240 VAC (10% power supply to the power supply input terminal as follows: 100 to 240 VAC ±10% (50/60 Hz) Insulating transformer 1:1 NE-W01E body Protective Earthing ■ Grounding precautions The following describes the precautions to follow when grounding the NEW01E.
Periodic Maintenance and Inspection ■ Maintenance • Inspect the NE-W01E once every six months to one year. Inspect the NE-W01E at shorter inspection periods if it is used in extremely high-temperature and/or high-humidity or dusty environments. • If you cannot remove dirt or dust on the NE-W01E by wiping with a soft, dry cloth, wipe with a firmly wrung cloth moistened with watered down neutral detergent.
Specifications ■ General specifications Item Power supply voltage Current consumption Overvoltage category Ground Operating ambient temperature Storage temperature Operating ambient humidity Storage humidity Pollution degree Withstand voltage Insulating resistance Vibration resistance Ambient atmosphere Weight Applicable standards NE-W01E 100 to 240 VAC ±10% (50/60 Hz) 10 VA max. II Class D earth (max.
■ Wireless LAN specifications Item Data transmission rate Network standard Frequency band Network architecture Transmission system Modulation system NE-W01E 1/2/5.5/11 Mbps (automatically selected) IEEE802.11b 2.4 GHz Infrastructure mode DS-SS (Direct Sequence Spread Spectrum) DBPSK (at 1 Mbps) DQPSK (at 2 Mbps) CCK (at 5.5/11 Mbps) 11 Open areas: Approx. 200 m Indoors: Approx. 40 m WEP 64/128 bit Max. 16 units can be registered.
■ Defaults (factory settings) These are the settings that are set on the NE-W01E before it is shipped from the factory. Item Unit name Password IP setting mode IP address Subnet mask Gateway address ESSID Channel Encryption (WEP) Setting Value NE-W01E None Fixed 192.168.0.13 255.255.255.0 0.0.0.0 KeyenceWLAN 1 OFF ■ MAC addresses A "MAC address" is a unique address that is assigned to each individual device, and comprises six bytes or 48 bits.
External Dimensions 64.5 4-M3 (mounting screws) Eff. screw depth 5 mm 124 13.5 70 ✽ Min. bending radius 24 mm (R ) 24 109 120 140 125.5 106 40 30.2 (70) 33.8 30.7 68.5 ø10 17 ø8.7 9.5 63 ø7.4 25.9 ✽ When Keyence STP cable is used ■ Expanded view when rubber caps are attached 1.
■ Magnet mounting diagram 50 22.6 20.6 2.1 (magnet clearance) 33.9 29.5 (front perspective) ■ Wall mounting diagram 52.5 37.5 20.5 7.5 7.
Warranty 1. Warranty Period The warranty period for this product shall be one year from the date of purchase at the specified location. 2. Scope of Warranty (1) If a malfunction due the liability on the part of KEYENCE CORPORATION arises during the above warranty period, this product shall be repaired free of charge.
KEYENCE CORPORATION 1-3-14, Higashi-Nakajima, Higashi-Yodogawa-ku, Osaka, 533-8555, Japan PHONE: +81-6-6379-2211 FAX: +81-6-6379-2131 30 ©KEYENCE CORPORATION, 2003 0103-2 96M1068 Printed in Japan
