Instruction Manual

12 13
Help Command:
KD-X222PO > H
-------------------------------------------------------------------------
-- Key Digital Systems HELP --
-------------------------------------------------------------------------
-- KD-X222PO System Address : 00 F/W Version : 1.00 --
-- Azz : All Commands may have Prex System Address zz=[01-99] --
-- H : Help --
-- STA : Global Status --
-- SPCA xx : Set System Address, xx = [00-99] (00=Single) --
-- --
-- Video I/O Setup Commands: --
-- SPO DBG ON/OFF : Set Output DGB ON/OFF --
-- SPO ON/OFF : Set CAT5e/6 Output ON/OFF --
-- --
-- SPC ART ON/OFF : Set HD-BaseT Auto Reset ON/OFF --
-- SPC RSB z : Set RS232 Baud Rate to z bps, z=[0-4] --
-- [0:57600, 1:38400, 2:19200, 3:9600, 4:4800] --
-------------------------------------------------------------------------
Specifications
Technical:
» Inputs Tx (Each): 1 HDMI, 1 IR In
» Outputs Tx (Each): 1 CAT5e/6 UTP/STP, 1 IR Out /RS-232 Bi-Directional
» Inputs Rx (Each): 1 CAT5e/6 UTP/STP, 1 IR In
» Outputs Rx (Each): 1 HDMI, 1 IR Out /RS-232 Bi-Directional
» DDC Signal (Data): Input DDC Signal: 5 Volts p-p (TTL)
» HDMI Video/Audio Signal: Input Video Signal: 1.2 Volts p-p
» HDMI Connector: Type A, 19 Pin Female
» RJ45 Connector: Shielded Link Connector, HDBaseT
» IR In Connector: Phoenix Connectors
» IR Out (RS-232) Connector: Phoenix Connectors
General
» Regulation: CE, RoHS, WEEE
» Enclosure: Black Metal
» Product (Each): 4.1” x 2.8” x 0.875”, Weight: 0.75 lbs
» Power (Tx Only): KD-PS12V2ASC, 12V/2A, 100-240VAC, 50-60Hz, Interchangeable head
with screw-in connector
» Accessories: (2) Mounting Brackets, (1) IR Emitter, (1) IR Sensor
Important Product Warnings:
1. Connect all cables before providing power to the unit.
2. Test for proper operation before securing unit behind walls or in hard to access spaces.
3. If installing the unit into wall or mounting bracket into sheet-rock, provide proper screw support
with bolts or sheet-rock anchors.
Safety Instructions:
Please be sure to follow these instructions for safe operation of your unit.
1. Read and follow all instructions. Heed all warnings.
2. Do not use this device near water. Clean only with dry cloth.
3. Install in accordance with the manufacturer’s instructions.
4. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
5. Only use attachments/accessories specified by the manufacturer.
6. Refer all servicing to qualified service personnel. Servicing is required when the device has been
damaged in any way including:
» Damage to the power supply or power plug
» Exposure to rain or moisture
Power Supply Use:
You MUST use the Power Supply PROVIDED with your unit or you VOID the Key Digital
®
Warranty
and risk damage to your unit and associated equipment.
Contacting Key Digital
®
Technical Support
For technical questions about using Key Digital
®
products, please contact us at:
› Phone: [phone] or E-mail: [e-mail]
Repairs and Warranty Service
Should your product require warranty service or repair, please obtain a Key Digital
®
Return Material
Authorization (RMA) number by contacting us at:
› Phone: [phone] or E-mail: [e-mail]
Warranty Information
All Key Digital
®
products are built to high manufacturing standards and should provide years of trouble-
free operation. They are backed by a Key Digital Limited 3 Year Product Warranty Policy.
http://www.keydigital.com/warranty.htm