Instruction Manual

ManualsBrandsKeydigital ManualsHDMIKeydigital 4K HDMI over CAT5e/6 HDBaseT Extender Tx + Rx Kit

2 1

Key Features

› HDBaseT via Single CAT5e/6 UTP/STP Extension: With fully automatic adjustment of feedback,

equalization, and ampliﬁcation depending on cabling length

› Power over HDBaseT: Tx unit powers Rx unit. Only one power connection needed.

› Signal Extension:

» Up to 150 ft. @ 4K 24/25/30(4:4:4)/60(4:2:0) using CAT6A cabling

» Up to 125 ft. @ 4K 24/25/30(4:4:4)/60(4:2:0) using CAT5e/6 UTP/STP cabling

» Up to 250 ft. @ 1080p / 1920x1200 using CAT6A cabling

» Up to 230 ft. @ 1080p / 1920x1200 using third-party CAT5e/6 UTP/STP cabling

› HDCP 2.2: Compliancy up to HDCP 2.2 and backward compliant

› HDR (High Dynamic Range): HDR is achieved with AppleTV source at 4K/30 [4:2:2] 12bit deep

color, enabling more life-like images through a greater range of luminance levels.

› 4K/Ultra HD Resolution: Supports signals up to 4096x2160 60Hz [4:2:0] 8bit, 4096x2160 30Hz

[4:2:2] 12bit, and 4096x2160 30Hz [4:4:4] 8bit

› Deep Color Support: Up to UHD/4K 30Hz 4:2:2/12 bits or 60Hz 4:2:0/8 bit

› Low Proﬁle: Super slim chassis design

› HDMI

and HDCP Licensing: Fully licensed and compatible with HDCP 2.2 and HDMI latest

technology such as 4K/UHD 4:2:0/8bit at 60f/s

› EDID Control: Internal library features 15 default EDID conﬁgurations and native EDID data from

Output/Display devices connected via Rx

› Hot Plug Detection Control: Enables integrator to choose if active signal voltage is forced to

connected input devices

› Full Buffer System

™

: Manages TMDS re-clocking / signal re-generation, HDCP authentication

with source & display, EDID Control handshake, and Hot Plug control

› IR Sensor: Sensor powering via +5V on Rx unit’s IR In port collects line-of-sight IR from remote(s)

without external IR connecting block

› Up/Down IR: Two channels of IR enable control to/from devices connected to Tx and Rx units

› RS-232: Bi-Directional control to/from Tx and Rx unit on Phoenix connector

› Rotary Switch RS-232 Control Mode: Provides control of Tx unit as well as connectivity status

› 3D: Support for standard 3D stereoscopic signal formats

› Surround Sound Audio: Supports Dolby

TrueHD, Dolby

Digital Plus, Dolby Atmos

, and DTS-HD

Master Audio

™

multi-channel audio formats

› CEC Support: For inter-device control between input and output HDMI channel

› I2C Communication: EDID and HDCP authentication to Display and Source

› Control System Support: Fully controllable by all RS-232 supported control systems via open API:

Compass Control

, AMX

, Crestron

, KNX

, RTI

, Savant, URC

, Leviton

etc.

Table of Contents

Key Features ..................................................................1

Quick Setup Guide ..............................................................2

Installation and Operation .........................................................2

Application Example .............................................................3

Connections ...................................................................4

Extending IR or RS-232 Control .....................................................5

Settings ......................................................................8

LED Indicator Lights ............................................................10

RS-232 Commands ............................................................10

Speciﬁcations .................................................................12

Always follow the instructions provided in this Operating Manual.

Please visit www.keydigital.com for the latest product documentation and software

downloads. Product features and speciﬁcations are subject to change without notice.

Introduction

Key Digital

KD-X222PO HDBaseT/HDMI (Tx + Rx) Extenders are an HDCP 2.2 compliant product that

extend 4K/UHD 24/25/30 (4:4:4) and 4K/UHD 60 (4:2:0) signals up to 150 ft. using CAT6A cable, or

up to 125 ft. using a CAT5e/6 cable. 1080p/60, 1920x1200, 3D signals are extended up to 250 ft.

via CAT6A cable, or up to 230 ft. using a CAT5e/6 cable. In addition to HDMI video and audio signals,

KD-X222PO carries IR or RS-232 for controlling remotely located equipment or the RS-232 port can

be used to control the KD-X222PO.