User Manual

45
SCALE TUNING (ARABIC)
F0H 26H 7BH 0AH Chan Data1...Data12 F7H
Data: 00H-7FH; 40h = no detune Chan: 00H-1FH 7FH all channels ( not drum sections)
MASTER TUNE
F0H 26H 7BH 0CH 00h Data1,Data2 F7H
Data1 00H-0CH high nibble Es. Data1=06h Es. Data1=00h Es. Data1=0Ch
Data2 00H-0FH low nibble
Data2=04h (nominal) Data2=00h (-100%) ata2=08h +100%)
GLOBAL GM RESET
F0H 26H 7BH 0EH 00h Value F7H Value = 00H gm controls reset
Value = 01H gm controls reset + all note off
GM DRUM PART
F0H 26H 7BH 0FH 00H GMPart Value F7 Value = 00H voice
Value = 01H drum
GMPart = 00H-1FH
GM MIDI RX CHANNEL ASSIGN
F0H 26H 7BH 12H 00H GMPart Chan F7H Chan = 00H-20H, 20H=OFF
GMpart 00H-1FH
VELOCITY SLOPE
F0H 26H 7BH 3EH 00H Part Value F7H Part : 00H-1FH Value: 00H-7fH
VELOCITY OFFSET
F0H 26H 7BH 3FH 00H Part Value F7H Part : 00H-1FH Value: 00H-7fH
FILTER VELOCITY SLOPE
F0H 26H 7BH 40H 00H Part Value F7H Part : 00H-1FH Value: 00H-7fH
FILTER VELOCITY OFFSET
F0H 26H 7BH 41H 00H Part Value F7H Part : 00H-1FH Value: 00H-7fH
MODULATION, BEND, AFTERTOUCH, VOICES CONTROLS
F0H 26H 7BH CNTRL 00H Part Value F7H Part : 01H-20H Value: 00H-7fH
CNTRL: 42H mod. pitch ctrl 49H bend pitch control 5AH AfterTouch tvf cutoff 62h Voices amplitude
43H mod. tvf cutoff 4AH bend tvf cutoff 5BH AfterTouch amplitude 63h Voicse lfo pitch
44H mod. lfo amplitude 4BH bend amplitude 5CH AfterTouch lfo pitch 64h Voices lfo tvf dpth
45H mod. lfo rate 4CH bend lfo pitch 5DH AfterTouch lfo tvf depth 65h Voices lfo tva dpth
46H mod. lfo pitch depth 4DH bend lfo tvf 5EH AfterTouch lfo tva depth
47H mod. lfo tvf depth 4EH bend lfo tva 60h Voices pitch ctrl
48H mod. lfo tva depth 59H AfterTouch pitch ctrl 61h Voices tvf cutoff
GENERAL MIDI VOLUME
F0H 26H 7BH 38H 00H Value F7H Value 00-7FH default: 7FH
GENERAL MIDI PAN
F0H 26H 7BH 39H 00H Value F7H Value 00-7FH default: 40H
MIDI PORT
F0H 26H 7BH 30H 00H Value F7H Value: 00H == Channels 00H - 0FH 01H == Channels 10H -1FH
DRAWBARS SELECTION
Controller 0 Value 67 Bank MSB Program Change 0
Drawbar Controller:
20 = 16’ Value: 0-127 24 = 2 2/3 Value: 0-127 28 = percussion 4’ Value: 0-127
21 = 8’ Value: 0-127 25 = 2’ Value: 0-127 29 = percussion 2’ 2/3 Value: 0-127
22 = 5 1/3’ Value: 0-127 26 = 1’ 3/5 Value: 0-127
23 = 4’ Value: 0-127 27 = 1’ Value: 0-127
I.E ( in order to send a drawbars data 16’- 8’- 4’)
Controller 0 value 67 Controller 20 value 127 (16’) Controller 23 value 127 (4’)
Program change 0 Controller 21 value 127 (8’)