Operator Manual User Manual

BIT 4886 120413 B-1
APPENDIX B - SCPI COMMAND/QUERY DEFINITIONS
B.1 INTRODUCTION
This appendix defines the SCPI subsystem commands and queries used with the BIT 4886 Inter-
face Card. Subsystem commands are defined in PAR. B.4 through B.92, arranged in groups as they
appear in the tree diagram, Figure 4-5. Table B-1 provides a quick reference of all SCPI subsystem
commands and queries used in the Interface Card.
TABLE B-1. SCPI SUBSYSTEM COMMAND/QUERY INDEX
COMMAND PAR. COMMAND PAR.
CAL:CPR B.3 [SOUR:]LIST:VOLT:POIN? B.47
CAL:STAT, ? B.4, B.5 [SOUR]:CURR, ? B.48, B.49
CAL:CURR B.6 [SOUR]:CURR:MODE, ? B.50, B.51
CAL:DATA B.7 [SOUR]:CURR:RANG, ? B.52, B.53
CAL:DPOT B.8 [SOUR]:CURR:RANG:AUTO B.54
CAL:LCURR B.9 [SOUR]:CURR:TRIG? B.55, B.56
CAL:LVOLT B.10 [SOUR]:VOLT B.57, B.58
CAL:SAVE B.11 [SOUR]:VOLT:MODE, ? B.59, B.60
CAL:VOLT B.12 [SOUR]:VOLT:RANG, ? B.61, B.62
CAL:VPR B.13 [SOUR]:VOLT:RANG:AUTO B.63
CAL:ZERO B.14 [SOUR]:VOLT:TRIG B.64, B.65
INIT[:IMM] B.15 STAT:OPER:COND? B.66
INIT:CONT, ? B.16, B.17 STAT:OPER:ENAB, ? B.67, B.68
MEAS:CURR? B.18 STAT:OPER[:EVEN]? B.69
MEAS:VOLT? B.19 STAT:PRES B.70
OUTP[:STAT], ? B.20, B.21 STAT:QUES[:EVEN]? B.71
[SOUR:]FUNC:MODE, ? B.22, B.23 STAT:QUES:COND? B.72
[SOUR:]FUNC:MODE:TRIG, ? B.24, B.25 STAT:QUES:ENAB, ? B.73, B.74
[SOUR:]LIST:CLE B.26 SYST:BEEP B.75
[SOUR:]LIST:COUN, ? B.27, B.28 SYST:COM:SER:ECHO, ? B.76, B.77
[SOUR:]LIST:COUN:SKIP, ? B.29, B.30 SYST:COM:SER:PACE, ? B.78, B.79
[SOUR:]LIST:CURR, ? B.31, B.32 SYST:ERR? B.80
[SOUR:]LIST:POIN? B.33 SYST:ERR:CODE? B.81, B.82
[SOUR:]LIST:DIR, ? B.34, B.35 SYST:PASS CEN, CDIS B.83, B.84
[SOUR:]LIST:DWEL, ? B.36, B.37 SYST:PASS:STAT B.86
[SOUR:]LIST:DWEL:POIN? B.38 SYST:REM, ? B.87, B.88
[SOUR:]LIST:GEN, ? B.39, B.40 SYST:SEC B.89
[SOUR:]LIST:QUER, ? B.41, B.42 SYST:SET, ? B.90, B.91
[SOUR:]LIST:SEQ, ? B.43, B.44 SYST:VERS? B.92
[SOUR:]LIST:VOLT, ? B.45, B.46
NOTE: Commands listed above that are followed by “, ?“ have a related query.