Manual

LIST OF FIGURES
FIGURE TITLE PAGE
BIT 232 022800
iii/iv Blank)
1-1 Remotely Controlled Power Supply Configurations Using Kepco Products............................................... vi
2-1 Installation of BIT Card into BOP ................................................................................................................ 2-2
2-2 BIT 232/BIT 232-F Switch and Adjustment Locations ................................................................................ 2-4
2-3 RS 232C Connector.................................................................................................................................... 2-5
3-1 BOP Power Supply, Internal Calibration Control Locations ........................................................................ 3-2
3-2 Current Shunt Connections......................................................................................................................... 3-5
4-1 Tree Diagram of SCPI Commands Used with BIT 232/BIT 232-F Interface Card ...................................... 4-3
4-2 Message Structure...................................................................................................................................... 4-5
A-1 *CLS — Clear Status Command.............................................................................................................. A-1
A-2 *ESE — Standard Event Status Enable Command ................................................................................... A-2
A-3 *ESE? — Standard Event Status Enable Query........................................................................................ A-2
A-4 *ESR? — Event Status Register Query .................................................................................................... A-3
A-5 *IDN? — Identification Query..................................................................................................................... A-3
A-6 *OPC — Operation Complete Command................................................................................................... A-4
A-7 *OPC? — Operation Complete Query ....................................................................................................... A-4
A-8 *RST — Reset Command.......................................................................................................................... A-5
A-9 *SRE — Service Request Enable Command............................................................................................. A-6
A-10 *SRE? — Service Request Enable Query ................................................................................................. A-6
A-11 *STB? — Status Byte Register Query ....................................................................................................... A-7
A-12 *TRG — Trigger Command ....................................................................................................................... A-7
A-13 *TST? — Self Test Query .......................................................................................................................... A-8
A-14 *WAI — Wait-to-continue Command.......................................................................................................... A-8
B-1 INITiate[:IMMediate] Command ................................................................................................................. B-1
B-2 INITiate:CONTinuous Command ............................................................................................................... B-2
B-3 INITiate:CONTinuous Query ...................................................................................................................... B-2
B-4 MEASure:CURRent? and MEASure:VOLTage? Queries........................................................................... B-3
B-5 CURRent Command .................................................................................................................................. B-4
B-6 CURRent Query......................................................................................................................................... B-4
B-7 CURRent:TRIGgered Command ............................................................................................................... B-5
B-8 CURRent:TRIGgered Query ...................................................................................................................... B-5
B-9 VOLTage Command ................................................................................................................................... B-6
B-10 VOLTage Query.......................................................................................................................................... B-6
B-11 VOLTage:TRIGgered Command ................................................................................................................ B-7
B-12 VOLTage:TRIGgered Query....................................................................................................................... B-7
B-13 FUNCtion:MODE Command...................................................................................................................... B-8
B-14 STATus:OPERation:CONDition Query....................................................................................................... B-8
B-15 STATus:OPEReration:ENABle Command.................................................................................................. B-9
B-16 STATus:OPEReration:ENABle Query ........................................................................................................ B-9
B-17 STATus:OPERation QUERY ...................................................................................................................... B-10
B-18 STATus:PRESet Command........................................................................................................................ B-10
B-19 STATus:QUEStionable? Query .................................................................................................................. B-11
B-20 STATus:QUEStionable:CONDition? Query ................................................................................................ B-11
B-21 STATus:QUEStionable:ENABle Command ................................................................................................ B-12
B-22 STATus:QUEStionable:ENABle? Query..................................................................................................... B-12
B-23 SYSTem:ERRor? Query............................................................................................................................. B-13
B-24 SYSTem:LANGuage Command................................................................................................................. B-13
C-1 FNC — Function Command....................................................................................................................... C-1
C-2 INX — Initiate Op Code Command............................................................................................................ C-2
C-3 FTH — Fetch Command............................................................................................................................ C-2
C-4 SET Command .......................................................................................................................................... C-3
C-5 RST — Reset Command ........................................................................................................................... C-4
C-6 CNF, IST — Confidence Test, Internal Self Test Commands.................................................................... C-4
C-7 STA — Status Command........................................................................................................................... C-5
C-8 GAL — Go to Alternate Language Command .......................................................................................... C-6