www.CookWithKenyon.
Table of Contents Section Page Important Safeguards ..............................................................................................................3 How to use Grill Quick Start Tips ...............................................................................................................4 Product Specifications ............................................................................................................7 Installation Instructions Package Contents ...........
IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed including the following: 1. Read ALL instructions prior to using product. 2. Do not touch hot surfaces. Use handles or knobs. 3. To protect against electrical shock, do not immerse cord or plugs in water or other liquid. 4. Close supervision is necessary when any appliances are used near children. 5. Allow to cool before putting on or taking off parts. 6.
Q U I C K S TA R T T I P S Thank you for purchasing the World’s Finest All Seasons® Electric Grill! There are a few simple steps you can take to ensure your good decision will lead to years of World-Class Grilling: 1. Remove grate(s) and drip tray(s), clean both. 2. Insert the drip tray(s) into the bottom of grill. Make sure the burner brackets are not resting on the drip tray(s). VISIT OUR WEBSITE to purchase recipe books, cooking utensils, griddles, grill covers, and more! 3.
1. Before using your grill, remove the cooking grate and drip tray from the grill. Wash the grill with warm soapy water using a non-abrasive cloth. USE ONLY HIGH TEMP PLASTIC UTENSILS WHEN GRILLING. Visit our web site to purchase a set of high quality stainless steel/high temp plastic grill utensils, www.cookwithkenyon.com. 2. Make sure the drip trays are inserted all the way into the bottom of grill and electric element brackets are resting on the element support bracket. 3.
Grate Drip Tray Electric Elements Fig. 1 12. To clean the grill, first be sure the cooking surface has cooled enough to handle. Then remove the grates, lift up the electric elements until they lock in the up position, remove the middle grate support cross bar, then the drip trays. The grate support cross bar is removed by lifting the rear and pulling the front notch off of the supporting tab. To install the support reverse the procedure. Do not cook on the grate without the support in place! 13.
PRODUCT SPECIFICATION The Texan Grill Models: B70400WH, B70400WHSCHUKO, B70400WHUK, B70400WHAU, B70401WH, B70401WHSCHUKO, B70401WHUK, B70401WHAU, B70405WH, B70405WHSCHUKO, B70405WHUK, B70405WHAU, B70410WH, B70410WHSCHUKO, B70410WHUK, B70410WHAU, B70420WH, B70420WHSCHUKO, B70420WHUK & B70420WHAU 240V AC 50/60Hz - 3000 WATTS - 13 AMPS Overall dimensions: 29.5” x 21” x 3.
INSTALLATION Package Contents Your Texan grill is assembled and ready for installation. Before you install the grill write your unit’s serial number here for future reference: _________________. The serial number can be found on the bottom center of the grill next to the drain fitting. The serial number consists of six digits. Contained in the shipping container is the Texan Grill, nine (9) mounting screws, manual, stainless steel cleaner and three (3) feet of drain hose with brass fitting.
Electrical Requirements Check the Electrical Supply Requirements This product must be installed in accordance with national, state and local electric codes. The following table provides the correct voltage, amperage and frequency that must be supplied to the grill. The supply must be from an individual grounded circuit that is protected by a circuit breaker and rated per the specifications for the model as shown in the table below.
Countertop Installation Your Texan Grill is supplied with a factory installed polished stainless steel flange that accepts nine oval head wood screws for mounting. The trim flange of the grill is designed to hold the unit firmly in place in the countertop. If desired, you may seal the edge of the countertop beneath the trim flange. We recommend a NON-ADHESIVE such as acrylic latex caulk. This will help reduce the chance of damage to the trim flange should the unit need to be removed from the countertop.
Before making the countertop cutout, check for clearance. Check to see that the grill will clear the front and side walls of the base cabinet. Also check for proper clearance to the back splash so that the lid can open fully. Adequate ventilation of the space below the countertop must be provided to ensure proper operation of the grill. Heat transferred from the grill bottom pan during operation will overheat an improperly ventilated area. 2 INCH (51MM) MINIMUM Fig.
Final Preparations Prior to Use Remove the protective plastic film from the lid, trim flange and glass panel. Clean the grill before you use it for the first time. A thorough cleaning with a stainless steel or glass cleaner will remove any traces of plastic film adhesives and manufacturing oils. Wash the nonstick coated grates in warm soapy water before using the grill. OPERATION OF GRILL DO NOT USE WATER ON GREASE FIRES Smother fire or flame or use dry chemical or foam-type extinguisher.
Touch Control To activate an element, first the master power must be turned on by placing and holding a finger for two seconds over the circular area next to the master power graphic. An audible beep will be heard and a light next to the master power graphic will illuminate. Then the desired element must be turned on, by placing a finger over the circular area marked ON/OFF for that element. The same beep will sound and a light will illuminate.
CALIBRATION Upon application of electrical power to the grill, the controller will run a self-calibration process. The controller will then sound an audible confirmation tone and the display will briefly illuminate. The grill is now ready to be used. For proper calibration the glass above the controller must be clear of any debris. Fig. 10 HEAT SETTINGS Your Texan Grill has 8 different heat settings, 1 through 8, selected using the (-) and (+) sensors. The heat setting is displayed as shown at the right.
TURNING “OFF” THE GRILL To turn off the grill, simply touch and hold the Master Power Sensor for two seconds. The controller will de-energize and shut off the heating element. AUTOMATIC SHUT-OFF The electronic control of your KENYON grill has been programmed with safety in mind and features an automatic shut-off. The grill is programmed to shut down after predetermined time after being energized (see table below). The control will also shut off if it reaches a preset temperature limit.
Grill Parts HEATING ELEMENTS The heating elements are designed to pivot as shown to remove/replace the baffle tray and drip trays. They will stay in the up position. To put down apply slight downward pressure. GRATES BAFFLE TRAY The baffle tray supports the drip trays, heating elements and grates and must always be used when operating the grill. The cross bar must also be installed to support the elements and grates.
Lid Removal LID REMOVAL The grill lids are removable for cleaning . To remove the lids, open it so the bearing is aligned with the notch in the lidstay. Pull the lidstay toward the center of the grill, over the bearing, releasing the lid from the lidstay mechanism. Then slide the quick release pin out of the middle hinge. (See Fig.
Handle Lock HANDLE LOCK The handle lock allows the user to lock both lids together for ease of opening and accessing the entire grilling surface. (See Fig. 16) The lids can also be unlocked and opened individually for access to either half of the grilling surface. (See Fig. 17) Slide & Twist Unlock Lock Handles Locked Fig. 16 Slide & Twist Unlock Lock Handles Unlocked Fig.
Statement of Warranty KENYON Kenyon International, Inc (the “Company”) warrants its products in normal usage to be free of defects in materials and workmanship subject to the conditions and limitations below. Any part, which proves to be defective in normal usage during the warranty period will be repaired or replaced by the Company. In order for product to be covered under this warranty it must be returned to the Company for evaluation. Please contact kenyonservice@cookwithkenyon.
