KDC-BT43U KDC-BT33U CD-RECEIVER INSTRUCTION MANUAL CD-RECEIVER BEDIENUNGSANLEITUNG CD-PECИBEP ИHCTPУKЦИЯ ПO ЭKCПЛУATAЦИИ CD-РЕСІВЕР ІНСТРУКЦІЯ З ЕКСПЛУАТАЦІЇ Изделие изготовлено во Франции © 2012 JVC KENWOOD Corporation CoverRear_GET0859_004A.
Information on Disposal of Old Electrical and Electronic Equipment and Batteries (applicable for EU countries that have adopted separate waste collection systems) Products and batteries with the symbol (crossed-out wheeled bin) cannot be disposed as household waste. Old electrical and electronic equipment and batteries should be recycled at a facility capable of handling these items and their waste byproducts. Contact your local authority for details in locating a recycle facility nearest to you.
Декларація про Відповідність Вимогам Технічного Регламенту Обмеження Використання деяких Небезпечних Речовин в електричному та електронному обладнанні (затвердженого Постановою №1057 Кабінету Міністрів України) Виріб відповідає вимогам Технічного Регламенту Обмеження Використання деяких Небезпечних Речовин в електричному та електронному обладнанні (ТР ОВНР). Вміст небезпечних речовин у випадках, не обумовлених в Додатку №2 ТР ОВНР: 1. свинець(Pb) – не перевищує 0.
CONTENTS BEFORE USE BEFORE USE 2 Warning BASICS 3 Do not operate any function that takes your attention away from safe driving. GETTING STARTED 4 Caution RADIO 5 CD / USB / iPod 6 AUX 7 BLUETOOTH® 8 DISPLAY SETTINGS 11 AUDIO SETTINGS 12 MORE INFORMATION 13 TROUBLESHOOTING 13 SPECIFICATIONS 15 INSTALLATION / CONNECTION 16 Volume setting: • Adjust the volume so that you can hear sounds outside the car to prevent accident.
BASICS Faceplate Volume knob KDC-BT43U (turn/press) Remote control (RC-406) Loading slot Attach KDC-BT43U can be remotely controlled with an optionally purchased remote control. Remote sensor (Do not expose to bright sunlight.) Detach Pull out the insulation sheet when using for the first time. KDC-BT33U How to reset How to replace the battery Your preset adjustments will also be erased. Detach button To Do this (on the faceplate) Do this (on the remote control) Turn on the power Press L SRC.
GETTING STARTED 3 Set the initial settings 1 2 3 4 1 Cancel the demonstration When you turn on the power (or after you reset the unit), the display shows: “CANCEL DEMO” \ “PRESS” \ “VOLUME KNOB” 1 Press the volume knob. Press SRC to enter [STANDBY]. Press the volume knob to enter [FUNCTION]. Turn the volume knob to select [INITIAL SET], then press the knob. Turn the volume knob to make a selection (see the following table), then press the knob. 5 Press and hold to exit.
RADIO Default: XX LOCAL SEEK SEEK MODE AUTO MEMORY Search for a station 1 Press L SRC to select TUNER. 2 Press repeatedly (or press *AM– / #FM+ on RC-406) to select FM1/ MONO SET PTY SEARCH FM2/ FM3/ MW/ LW. 3 Press 4 / ¢ (or press 4 / ¢ (+) on RC-406) to search for a station. • To store a station: Press and hold one of the number buttons (1 to 6). • To select a stored station: Press one of the number buttons (1 to 6) (or TI NEWS SET AF SET press one of the number buttons (1 to 6) on RC-406).
CD / USB / iPod Start playback CD Label side 0: Eject disc The source changes to CD and playback starts. USB USB input terminal CA-U1EX (max.: 500 mA) (optional accessory) Note (for KDC-BT43U ): Pairing request (via Bluetooth) is automatically activated if an iPhone/iPod touch is connected through the USB input terminal. (➜ 8, 10) KDC-BT43U : Applicable — : Not applicable To Do this Pause or resume playback Press 6 38 (or ENT 38 on RC-406).
CD / USB / iPod Direct Music Search (using RC-406) (for KDC-BT43U ) 1 Press DIRECT. 2 Press the number buttons to enter a track/file number. 3 Press 4 / ¢ (+) to search for music. • To cancel, press . • Not available if Random Play is selected. • Not applicable for iPod, KME Light/ KMC file. (➜ 13) Set the skip ratio 1 2 3 4 Select a song by name (for KDC-BT43U ) 1 2 3 4 5 6 7 While listening to iPod... Press . Turn the volume knob to select a category, then press the knob. Press again.
BLUETOOTH® You can operate Bluetooth devices using this unit. Connect the microphone For KDC-BT43U : MIC (Microphone input terminal) Microphone (supplied) Pair a Bluetooth device When connecting a Bluetooth device to the unit for the first time, perform pairing between the unit and the device. Once the pairing is completed, the Bluetooth device will remain registered in the unit even if you reset the unit. • Up to five devices can be registered (paired) in total.
BLUETOOTH® Bluetooth mobile phone To Receive a call Bluetooth mode operations Do this Press or the volume knob or one of the number buttons (1 to 6) (or on RC-406). • The button illuminates and flashes in red when there is an incoming call. During a call, the button illuminates in red. • When [AUTO ANSWER] is set to the selected time, the unit answers incoming call automatically. (➜ 10) Reject an incoming call Press L SRC (or End a call Press press the knob.
BLUETOOTH® Default: XX SETTINGS PAIRING PHONE SELECT/ PHONE SEL : Select the phone or audio device to connect or disconnect. AUDIO SELECT/ AUDIO SEL DEVICE DELETE/ DVC DELETE TRANSFER PB* : “DL PB 1 Turn the volume knob to select a device to delete, then press the knob. 2 Turn the volume knob to select [YES] or [NO], then press the knob. ” appears and transfer the phonebook of the connected phone to this unit manually.
BLUETOOTH® Store a contact in memory You can store up to 6 contacts. 1 Press to enter Bluetooth mode. 2 Turn the volume knob to select [PHONE BOOK], [HISTORY], or [NUMBER DIAL], then press the knob. 3 Turn the volume knob to select a contact or enter a phone number. 4 Press and hold one of the number buttons (1 to 6). “STORED” appears when the contact is stored. • To erase a contact from the preset memory, select [NUMBER DIAL] in step 2 and store a blank number.
AUDIO SETTINGS While listening to any source... 1 Press the volume knob to enter [FUNCTION]. 2 Turn the volume knob to select [AUDIO CONTROL]/ [AUDIO CTRL], then press the knob. 3 Turn the volume knob to make a selection (see the following table), then press the knob. Repeat step 3 until the desired item is selected or activated. 4 Press and hold to exit. 1 Press AUD to enter [AUDIO CONTROL]. 2 Press 5/∞ to make a selection, then press ENT 38. .
MORE INFORMATION General • This unit can only play the following CDs: • Detailed information and notes about the playable audio files are stated in an online manual on the following site: www.kenwood.com/cs/ce/audiofile/ Playable files • Playable Audio file: AAC (.m4a), MP3 (.mp3), WMA (.wma) • Playable disc media: CD-R/RW/ROM • Playable disc file formats: ISO 9660 Level 1/2, Joliet, Romeo, Long file name.
TROUBLESHOOTING Remedy “NO DEVICE” appears. Connect a USB device, and change the source to USB again. “COPY PRO” appears. A copy-protected file is played. “NO MUSIC” appears. Connect a USB device that contains playable audio files. “NA DEVICE” appears. Connect a supported USB device, and check the connections. “USB ERROR” appears. • Remove the USB device, turn the unit off, then turn it on again. • Try to connect another USB device. “iPod ERROR” appears. • Reconnect the iPod. • Reset the iPod.
USB Laser Diode Digital Filter (D/A) D/A Converter Spindle Speed Wow & Flutter Frequency Response (±1 dB) Total Harmonic Distortion (1 kHz) Signal-to-Noise Ratio (1 kHz) Dynamic Range AAC Decode MP3 Decode WMA Decode GaAIAs 8 times over sampling 24 Bit 500 rpm to 200 rpm (CLV) Below measurable limit 20 Hz to 20 kHz 0.01 % 105 dB 90 dB AAC-LC “.
INSTALLATION / CONNECTION Installating the unit (in-dash mounting) Warning • The unit can only be used with a 12 V DC power supply, negative ground. • Disconnect the battery’s negative terminal before wiring and mounting. • Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire (black) to prevent a short circuit. • Insulate unconnected wires with vinyl tape to prevent a short circuit. • Be sure to ground this unit to the car’s chassis again after installation.
Wiring connection Part list for installation Rear/subwoofer output MIC (Microphone input terminal) (➜ 8) A Faceplate Fuse (10 A) Antenna terminal REAR/SW ( ×1 ) B Mounting sleeve If no connections are made, do not let the wire come out from the tab. Light blue/yellow STEERING WHEEL REMOTE INPUT (Steering remote control wire) REMOTE CONT Blue/White (Power control wire/ Antenna control wire) ANT CONT P.
