You should have received the following parts in the package. Please ensure that all parts are accounted for.
IBIZA LARGE TIERED FOUNTAIN Care and Instruction Manual
51084SNDST ASSEMBLY INSTRUCTIONS Thank you for purchasing a Kenroy Home water feature, you are now only minutes away from filling your home or outdoor living space with peaceful displays. Our guarantee backs all of our water features, please do not hesitate to contact our Customer Support Team for resolutions to any parts or installation concerns. CUSTOMER SUPPORT TEAM For any additional questions or concerns please contact our Customer Support Team: 904-642-4340 @KenroyHome customerorders@kenroyhome.
1084SNDST ASSEMBLY INSTRUCTIONS Please reference the separate parts list and ensure that all pieces are included in the package prior to assembly. To protect the finish, place all parts on a soft surface when unpacking. More than one person may be required to complete the assembly of this product. When assembling ensure that all parts are firmly tightened. Choose a location: This freestanding water feature is attractive from all sides and can be used to highlight almost any area.
51084SNDST ASSEMBLY INSTRUCTIONS Place lower reservoir (B) onto base (A) and twist it clockwise to secure. Feed pump cord and light cord through plastic tube, make sure the cords exit out from notch on bottom of base (A). Place pump (H) and two spot lights (J) into lower reservoir (B). H J Plastic tube B A B A Place lower column (C) into lower reservoir (B) and twist it clockwise to secure. Place upper reservoir (D) onto lower column (C) and twist it clockwise to secure.
51084SNDST ASSEMBLY INSTRUCTIONS Place middle column (E) into upper reservoir (D) and twist it clockwise to secure. E D Feed rubber hose through plastic tube, place upper column (F) into middle column (E) and twist the upper column (F) clockwise to secure.
51084SNDST ASSEMBLY INSTRUCTIONS Take out the pump (H) and attach to rubber hose, replace the pump (H) and cover the entry with pump access door (G). Rubber hose H G FINAL STEPS Fill the lower reservoir (B) with 6.55 gallons of distilled water. Water should remain above the fill line on pump access door while the fountain is running. 7 Connect the light connectors (I) and (J) and screw the cap tightly. Plug pump (H) and light transformer (I) into outlets and turn light on at switch.
51084SNDST ASSEMBLY INSTRUCTIONS PUMP SAFETY & TROUBLESHOOTING To clean the pump Unplug the pump from the electrical outlet. Use a small soft brush or place it under a water stream to remove debris. To keep water clean Periodically change water to prevent algae buildup. Tube Rotor/Impeller Impeller cover Back cover Pump housing Suction cup Front cover Flow regulator If the pump fails to run: • Check circuit breaker, or try a different outlet. • Check tubing for kinks and obstructions.
51084SNDST ASSEMBLY INSTRUCTIONS WATER FEATURE WARNINGS & TROUBLESHOOTING • To reduce the risk of electrical shock, always disconnect the power supply before working with the water feature. • Splashing may occur when the fountain is first turned on, protect surrounding surfaces as needed. Do not place the water feature on or near any surface that can be damaged by water. • Water flow rate may need to be adjusted from factory settings.
51084SNDST ASSEMBLY INSTRUCTIONS FREQUENTLY ASKED QUESTIONS What should I consider when selecting a water feature? In addition to your personal style tastes, be sure you have an area for your water feature that can be safely exposed to water, as splashing can occur. Also take into consideration what a water feature can add to your environment: the sound of flowing water or decorative lights.
51084SNDST ASSEMBLY INSTRUCTIONS FREQUENTLY ASKED QUESTIONS CONTINUED The water is not flowing evenly over my water feature’s surface. How do I correct this? Oil and dirt from your hands or the environment my interrupt proper water flow. Use the water guiding pad (if included with your model) or a mildly abrasive scrub pad and mild soap to clean the surface of the water feature.
51084SNDST ASSEMBLY INSTRUCTIONS FREQUENTLY ASKED QUESTIONS CONTINUED My pump is making a loud noise. How do I fix that? 1. Be sure the pump is fully submerged in water. If it is not, and pulling in air, it will make unwanted noise. 2. Check to make sure the pump is not touching the water feature anywhere other than the bottom. If it is up against the side wall or another part, the vibration from the pump can cause unwanted noise.
www.kenroyhome.
