IONVWdSa 721.80402 721.80403 721.80404 721.80409 721.80522 721.80523 721.80524 721.80529 721.80414 721.80419 721.80413 721.80412 INSTALLATION INSTRUCTIONS INSTRUCCIONES DE INSTALACION HSIIDSNa Models/Modelos Kenmore § Read and save these installation instructions. Lea y guarde estas Microwave Hood Combination Combinacion Microondas Campana instrucciones de instalacion Part No. 3828W5U0437 Sears, Roebuck and Co., Hoffman Estates, IL.60179 U.S.A www.sears.com.
YOUR SAFETY FIRST BEFORE YOU START ¢ Proper installation is the installer's responsibility! — Read the entire manual before you begin. ~— The model number label is located on the oven front. See Figure 1. — Mounting plate is located on back side of microwave oven. See Figure 2. BE SURE TO READ THE FOLLOWING SAFETY INSTRUCTIONS: Mounting Plate HSIIDSNa Model Number Label Figure 1 Figure 2 A WARNING A FOR YOUR SAFETY: ® You will need TWO people to install this oven.
YOUR SAFETY FIRST e THIS APPLIANCE MUST BE GROUNDED! — If there is an electrical short circuit, grounding reduces the risk of electrical shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug. PROPERLY POLARIZED AND « Place the plug into a properly installed and grounded GROUNDED OUTLET — outlet. See Figure 3.
YOUR SAFETY FIRST « MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT. A WARNING A If you do not mount the oven as instructed, you risk personal injury and/or property damage. 3 GRR Gomi ‘ 4- Grounded Plug (inside upper cabinet) aaa HSITSNa — Mount the oven against a flat, vertical wall, so that it is supported by the wall. The wall should be constructed of minimum 2" x 4" wood studding and 3/8" thick drywall or plaster/lath.
PARTS, TOOLS, MATERIALS THE FOLLOWING PARTS ARE SUPPLIED WITH THE OVEN: NOTE: Depending on your ventilation requirements, you may not use all of these parts.
PARTS, TOOLS, MATERIALS YOU WILL NEED THE FOLLOWING TOOLS AND MATERIALS FOR THE INSTALLATION: Carton or other heavy material for covering the counter top.
STEP 1: PREPARE THE ELECTRICAL CONNECTIONS A WARNING A AVOID ELECTRICAL SHOCK! THIS APPLIANCE MUST BE GROUNDED! 1. Locate the grounded electric outlet for this oven in the cabinet above the oven, as shown in Figure 4 Detail. : : Upper Cabinet . NOTE: The outlet should be on a circuit dedicated to the microwave oven 120V, 60Hz., AC only, with a 20ampere fused electrical supply. Grounded IMPORTANT: If you do not have the proper wall outlet, you MUST have one installed by a qualified electrician.
STEP 2: PREPARE THE VENTING SYSYTEM NOTE: The ductwork you need for outside ventilation is not included with your oven. The standard ductwork fittings and length are shown in Figure 9, page 9. A WARNING - FIRE HAZARD A THIS OVEN MUST BE PROPERLY VENTED! You may vent your oven in one of three ways: Wall Venting If your oven is located on an outside wall on the first floor of your house, as in Figure 5 (3-1/4" x 10" duct) and Figure 8 (6" round duct.
STEP 2: PREPARE THE VENTING SYSYTEM STANDARD FITTINGS NOTE: If the existing duct is round, you must use a rectangular-to-round adapter, with a rectangular 3" extension duct installed between the damper assembly and the adapter to prevent the exhaust damper sticking. DUCT LENGTH The total length of the duct system, including straight duct, elbows, transitions, wall or roof caps must not exceed the equivalent of 140 feet. For best performance, do not use more than three 90 degree elbows.
STEP 3: PREPARE THE VENTING BLOWER Your microwave oven is shipped with the blower assembled for room venting (recirculating). You need to adjust the blower if you want wall vented or roof vented installation. A WARNING A ELECTRICAL SHOCK HAZARD! UNPLUG UNIT BEFORE WORKING ON IT. HSITSNa e DO NOT PULL OR STRETCH THE BLOWER WIRING! Pulling and stretching the blower wiring could result in electrical shock. REMOVE THE MOUNTING PLATE: 1.
STEP 3: PREPARE THE VENTING BLOWER WALL VENTED INSTALLATION: 1. Remove one blower unit mounting screw and two blower plate screws. Remove the blower plate from cabinet. See Figure 12. back plate blower unit blower plate 2. Carefully lift the blower unit out of the microwave mounting screws oven. Disconnect the blower wire from connector. See Figure 13. 3. Use side cutters or tin snips to cut and remove blower plate knockouts. Be careful not to distort the plate. See Figure 14. 4.
STEP 3: PREPARE THE VENTING BLOWER ROOF VENTED INSTALLATION: blower plate 1. Remove one blower unit mounting screw and two blower plate screws. Remove the blower plate from cabinet. See Figure 18. mounting screws 2. Carefully lift the blower unit out of the microwave oven. blower plate mounting screw 3. Rotate blower unit 90° so the exhaust ports face the top of the cabinet. See Figure 19. HSITSNa A blower unit Figure 18 4. Place blower unit back into microwave oven. 5.
STEP 4: PREPARE THE WALL AND UPPER CABINET FOR INSTALLATION MEASURE AND TACK / TAPE UP THE TEMPLATE 1. Using a plumb line and (metal) measuring tape, find and mark the vertical center line “(V) on the back wall, as in Figure 22. 2. Find and mark one or two points where the studs are on the wall (Studs are normally 16 inches apart.) and then measure and mark the stud locations. If you cannot find any wall stud, consult a local building contractor.
STEP 4: PREPARE THE WALL AND UPPER CABINET FOR INSTALLATION DRILL THE HOLES IN THE WALL AND UPPER CABINET. A WARNING A BE VERY CAREFUL WHEN DRILLING HOLES INTO THE WALL. HSITSNa Electrical wires could be concealed behind the wall covering and if the drill hits them you could get an electric shock. 1. Find the points on the mounting plate labeled "A", “B", "C"™ and “D"™. Drill a 3/16" diameter hole at any of these points that are in front of a wall stud.
STEP 5: INSTALL THE MOUNTING PLATE TO THE WALL THE OVEN MUST BE CONNECTED TO AT LEAST ONE WALL STUD. 1. Draw a 3/16" Hole on Studs 3/4" Hole on Drywall Only Minimum 66" vertical line on the wall at the center of the From the Floor 30" wide space. For WailVented Only Use the mounting plate as the template for the rear wall. Place the mounting plate on the wall, making sure that the tabs are against the bottom of the cabinet.
STEP 5: INSTALL THE MOUNTING PLATE TO THE WALL TO PREPARE THE REAR WALL CUTOUT OPENING AND EXHAUST ADAPTOR/MOUNTING PLATE FOR WALL VENTING AND ROOF VENTING: 1 F. CUT OUT FOR WALL VENTED ONLY ‘Bg Hoke pypsoan pecs NOTE: ron oust ono If room vented installation is used, skip this step. 1. Place the mounting plate against the rear wail as described in step 5 item 1 (page 15). REAR WALL TEMPLATE 2. Use the wall template to determine the location and size of the box cutout for the rear wall duct.
STEP 6: ATTACH THE OVEN TO THE WALL ——— 4. WARNING A —— I power cord . Carefully lift microwave oven and hang it on support tabs (See Figure 26) at the bottom of the mounting plate. Reaching through upper cabinet, thread power supply cord through the power supply cord hole in the bottom of the upper cabinet. HSITSNa as You will need two people to lift this microwave. Failure to use more than one person could result in personal injury. See Figure 30. .
STEP 6: ATTACH THE OVEN TO THE WALL 5. Roof vented installation: See Figure 32. Install ductwork through the vent opening in the upper cabinet. Complete the venting system through the roof according to the method needed. See “PREPARE THE VENTING SYSTEM,” STEP 2 on the page 8. Use caulking to seal exterior roof opening around the exhaust cap. See Figure 6 on page 8. 6. Use power supply cord clamp to bundle the power supply cord.
MEMO 19
