Quick Start Manual

ManualsBrandsKenmore ManualsOvensKenmore 45599

I STALLAT

30" CT C

I STRUCT

P-I GE

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

United States

FOR YOUR SAFETY: Do not store or use gasoline

or other flammable vapors and liquids in the vicinity of this or

any other appliance.

Table of Contents

important Safety instructions ......................................... 2

Cutout Dimensions ....................................................... 3-4

Electrical Requirements ................................................... 5

Electrical Connection .................................................. 5-6

Serial Plate Location ....................................................... 6

Range installation ............................................................ 7

Anti-tip Bracket Installation ........................................ 8-9

Check Operation ........................................................... 10

Model and Serial Number Location ........................... 10

Before you call for Service ........................................... 10

important Notes to the Installer

1. Read att instructions contained in these

installation instructions before installing range.

2. Remove all packing material from the oven and

the drawer compartments before connecting the

electrical supply to the range.

3. Observe all governing codes and ordinances.

4. Be sure to leave these instructions with the

consumer.

important Note to the Consumer

Keep these instructions with your owner's guide for

future reference.

Printed in Canada

P/N 318201628 (1202) Rev. A

English - pages 1-10

Espahot - p6ginas 11-20

Summary of content (20 pages)

PAGE 1
I STALLAT 30" CT C I STRUCT P-I GE INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. United States FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Table of Contents important Safety instructions ......................................... 2 Cutout Dimensions .....................................
PAGE 2
iMPORTANT This manual follow SAFETY iNSTRUCTiONS contains important safety symbols and instructions. Please pay attention to these symbols and all instructions given. * Be sure your range is installed and grounded properly by a cluallfled installer or service technician. reduce by installing a range hood that project horizontally a minimum of 5 inches beyond the bottom of the cabinet.
PAGE 3
Cutout Dimensions ' 30" (76.2 cm Min.) See Note 3 I 18" Min. ',mJn. 311/2" (81 cm) Exact Shave Raised Edge to Clear Space for a 311/2"(81 cm) Wide Cooktop Rim. cmMin.) 1/2" _nin. C Locate Cabinet Doors 1" (2.5 cm) Min. from Cutout Opening 24" Min. 61 cm Min.) Grounded Junction adjoining Cabinet Box in Smoothtop Models Front (If Cabinet Fff]er required) 48" (122 cm) Armored Cable NOTE: Two sets of holes are provided under antitip bracket.
PAGE 4
NOTES: 1. Do not pinch the power supply cord between 2. Do not seal the range to the side cabinets. the range and the wall. 3. 24" (61 cm) minimum clearance between the cooktop and the bottom of the cabinet when the bottom of wood or metal cabinet is protected by not less than 1/4" (0.64 cm) flame retardant millboard covered with not less than No. 28 MSG sheet metal, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum, 0.020" (0.5 mm) copper. 30" (76.2 cm) minimum when the cabinet .
PAGE 5
Electrical Requirements This appliance must be supplied and frequency, and connected grounded branch circuit, or fuse 40A or 50A. Observe all governing 1. A 3-wire or 4-wire and black by a circuit phase electrical 120/240 supply DO NOT No. 70-latest C22.1, Canadian and ordinances. is required fuse neutral on must conform Electrical ° Electrical ground ° Do not connect Code, Shock is required is permanently on this appliance.
PAGE 6
(if your appliance white neutral (1996 NEC), is manufactured supply and a frame The frame is grounded lead to neutral with a white connected neutral wire.
PAGE 7
_R__ ||eTh_teCIcfricQ_ipOol3we | r fo the range shut off while llne connections are being made. Important Note: Door removal is not a requirement for installation of the range, but is an added convenience. The appliance should be placed on a table or the front of the appliance should be raised to be able to fully open the door. Please refer to the Use and Care Guide for oven door removal instructions. must be Failure fo do so could result in serious injury or death.
PAGE 8
Anti-tip Bracket installation A° Preferred Anti-tip 1. installation {All models). The range is equipped with an anti-tip bracket attached to the back of the range with two screws, if countertop thickness is greater than 1/2" (1.3cm), relocate anti-tip bracket to the lower position 1/4" (6.4 mm) below (see figure 4). 2. Anti-slide brackets installation (Figure 5): A.Ptace the range so that it is about 6" out of the cabinet. B.
PAGE 9
2. 3. Anti-Tip A.Instatl cabinet "L" brackets the anti-tip cabinet Installation: "L" brackets C. Alternate Anti tip installation (Model wlth liftup cooktop only_)_ 1. Anti-tip/anti-slide screws installation: A. Slide the range to its flnal position. B. Lift the cooktop and secure range burner box to cabinet with screws supplied to prevent range from tipping (Figure 8). 2. Install the decorative lower trim under the door as shown on Figure 7, one on each side. B.
PAGE 10
Checking Operation Model and Serial Number Location Some models have manual controls. Refer to the Owner's Guide and check all controls for correct The serial plate is located along the side of the oven door in the open position. operation. When ordering parts for or making inquires about your oven, always be sure to include the model and serial numbers and a lot number or letter from the serial plate on your oven. Some models are equipped with an electronic oven control.
PAGE 11
f NSTRUCCIO NSTALAC ELECTRICA EMPOTRABLE DE 30" LA INSTALACION Y EL SERVICIO DEBEN SER EFECTUADOS POR UN iNSTALADOR CALiFiCADO. iMPORTANTE: GUARDE ESTAS iNSTRUCCIONES PARA USO DEL iNSPECTOR LOCAL DE ELECTRICIDAD. LEA Y GUARDE ESTAS INSTRUCCIONES PARA REFERENCIA FUTURA. Estados Unidos PARA $U SEGURIDAD: No almacene ni ufitice gasoline u otros vapores V liquidos inNamables en la proximidad de este o de cualquier otto aHefacto. "rabla de materias Ubicaci6n de la ptaca de serie ...........................
PAGE 12
IMPORTANTES INSTRUCCIONES DE SEGURIDAD Este manual contlene importantes mensajes de segurldad. $1empre lea y obedezca todo mensaje de segurldad. * Aseg_rese que su coclna est_ instalada y conectada adecuadamente a tlerra pot un instaJador callficado o un t_cnlco de servlclo. * Esta coclna debe set conectada a tlerra * el_ctrlcamente de acuerdo con los c6digos locales, o de no existlr, con la National Electrlcal Code ANSI/NFPA No.70- _ltlrna edici6n. .
PAGE 13
Gabinefe Dimensiones I 30" (76.2cm) , (76,2 cm Min.) Vea Note 3 11/2"Max. 1/2" min. mJfl. j_, _,, 18 Mfn. (45,7cm Mh.) (3,8 cm) M6x. Lije la parte elevade del borde para obtener las 311/2'' (81 cm) de ancho dd reborde 311/2 '' (81 Exacto de la plancha de cocinar. 1/2" _nin. App. 1-7/8" (4,8 cm) ,, Ubique ias puertas de los armarios un minimo de 1" de ia abertura. // La caja de empaimes de conexi6n con la tierra. Cable Biindado NOTA: Hay dos juegos de agujeros debajo del soporte antivudco.
PAGE 14
NOTAS: 1. No peJJizque el cord6n eJ_ctrico 2. No selle la estufa a los armadas entre Ja estufa y Ja pared. de lado. 3. Un espacio m[nimo de 24" (61 cm) entre la superficie de la estufa y el rondo del armada cuando el rondo del armario de madera o metal est6 protegido par no menos de 1/4" (0.64 cm) de madera resistente al fuego cubierta par una 16mina met61ica de MSG, nOmero 28, 0.015" (0.4 mm) de acero inoxidable, 0.024" (0.6 mm) de aluminio, (80 cm) o 0.02" (0.5 mm) de cobre. 261/2" (67.
PAGE 15
Requerimientos Se debe proveer ei voltaje este electrodomSstico, El ctricos y la frecuencia y conectarse a un circuito correctamente puesto a tierra, protecjido o un fusible de 40A o 50A Observe locales todos 1.
PAGE 16
Esfe elecfrodom&sflco esf6 fabrlcado con un surnlnlsfro Si el horno se usa en una instalaci6n el&cfrlco neutro blanco y un alambre de cobre conectado al armaz6n. El armaz6n esfa puesfo a tlerra pot un enlace de la conexi6n a flerra con la conexi6n del neufro al final de la linea el&cfrlca, sl es usado en los estados unldos una nueva insfalaci6n de clrculfo ramal de blfurcaci6n el_ctrlco de 4 alambres. (ver figura 1.
PAGE 17
D Instalaci6n Nora importante: No es necesario, pero si es conveniente, quitar la puerta para instalar el horno. La unidad debe de ser colocada sabre una mesa o la parte frontal de la unidad debe de ser ievantada para poder abrir ia puerta enteramente. Consulte Ins instrucciones para retirar la puerta en la Gu_a de Usa y Cuidado. de la estufa La corrlen|e el_c|rlca a la es|ufa debe apagarse mlen|ras se hacjan Ins cone×lanes. Si no se hace esto puede provocar da_o serlo o muerte.
PAGE 18
L_ Instrucciones de instalaci6n de la fljaci6n anti-inclinaci6n A. Instalaci6n preferida anti-vuelco _Todos los modelos). 1. Esta estufa puede traer soportes antivuelco, fijados al dorso de ta estufa con dos tornillos. Si el grueso del tablero es m6s de 1/2" (1.3 cm), coloque de nuevo el soporte antivuetco en la posici6n m6s baja, de 1/4" (6.4 mm) (Vea Figura 4). 2. Instalaci6n de la m6nsula antideslizante (vea Figura 5). A.Colocar la cocina de manera que est6 a 6" del muebte. B.
PAGE 19
2. 3. C. Instalacion alterna anti-vuelco (Cocinas con parte superior elevable solamente)_ Instalaci6n de cabinete Anti-vuelco con braquet "L" brackets: A. Instale el cabinete anti-vuelco con braquets "L" como lo muestra la figura 7, une en cada lado. B. Deslice la estufa a su posici6n final (los braquets anti-vuelco montados en la estufa deberan tocalizarse debajo de los cabinetes anti-vuelco braquets "L" cuando la estufa se encuentre en su posici6n final).
PAGE 20
Cornprobaci6n del funcionarniento Ubicaci6n del n6rnero de rnodelo V de serie AIgunos modelos tienen controles manuales. Consulte el Manual del Usuario y aseg6rese de que todos los controtes funcionen correctamente. La plata con el n0mero de modelo y de serie est6 ubicada en et borde de la puerta del horno en la posici6n abierta. Atgunos modelos est6n equipados con un control electr6nico. Cada funci6n ha sido probada en la f6brica antes del transporte. Sin embargo, sugerimos que Ud.