Instruction Manual
Table Of Contents
- 1. General
- 2. Installation
- 2.1 Installing power source mains plug
- 2.2 Installing cooling unit (optional)
- 2.3 Installing equipment on cart (optional)
- 2.4 Connecting welding gun
- 2.5 Installing earth return cable
- 2.6 Installing remote control (optional)
- 2.7 Installing and replacing feed rolls
- 2.8 Installing and replacing wire guide tubes
- 2.9 Installing and changing wire
- 2.10 Installing gas bottle and testing gas flow
- 2.11 How to get welding programs
- 3. Operation
- 3.1 Preparing welding system for use
- 3.2 Calibrating welding cable
- 3.3 Using control panel
- 3.3.1 Control panel: Home view
- 3.3.2 Control panel: Weld Assist
- 3.3.3 Control panel: Channels
- 3.3.4 Control panel: WPS view
- 3.3.5 Control panel: Welding parameters
- 3.3.6 Control panel: Weld history
- 3.3.7 Control panel: Info view
- 3.3.8 Control panel: Device settings
- 3.3.9 Control panel: Applying welding programs
- 3.3.10 Control panel: Weld data view
- 3.4 Additional guidance to functions and features
- 3.5 Pulse welding
- 3.6 Wireless connection (WLAN)
- 3.7 Using remote control
- 3.8 Changing welding polarity
- 3.9 Lifting equipment
- 4. Maintenance
- 5. Technical data
Master M 358
Operating manual - EN
The WLAN mode is set to 'Client' by default and it cannot be changed.
3.6.1 Digital Welding Procedure Specification (dWPS)
The use of digital WPS (Welding Procedure Specification, dWPS) and WeldEye cloud service require a valid Kemppi WeldEye
subscription with the Welding Procedures module. For more information on WeldEye, refer to
weldeye.com or contact your
Kemppi representative.
Digital Welding Procedure Specification (dWPS) is a WPS in digital format that can be set to observe the welding para-
meters of the Master M 358 equipment. The WPSes can be read on the control panel display and/or a memory channel
can be linked with a WPS. The Master M 358 control panel provides a couple of ways to achieve this:
>> In the main WPS view: Follow the more detailed steps in "Control panel: WPS view" on page41.
>> In the Memory channels view via activating an existing memory channel: Open the memory channel 'Actions'
and choose to link it with a WPS. In the view that opens, select the WPS and weld pass information to be linked
with the memory channel. More detailed information on memory channels is in "Control panel: Channels" on
page39.
3.6.2 WeldEye ArcVision
The use of WeldEye cloud service requires a valid Kemppi WeldEye subscription. The Master M 358 equipment includes a link
to a free trial registration – featuring also a free trial option for WeldEye ArcVision. For more information on WeldEye, refer to
weldeye.com or contact your Kemppi representative.
The WeldEye's ArcVision module is intended for cloud-based tracking of the welding operations carried out with the
welding equipment. The ArcVision on the welding device itself is a connection feature for connecting to the WeldEye
cloud service. The actual welding information gathered by the welding equipment is passed on to the WeldEye cloud
where it can be accessed using a desktop computer and an internet browser.
To take the WeldEye ArcVision feature in use, the equipment must be connected to the internet via the built-in wireless
connection (WLAN). Refer to "Wireless connection (WLAN)" on the previous page for instructions.
Master M 358 comes preinstalled with a trial license for ArcVision. The trial license can be activated by following these
steps:
© Kemppi
62
1921980 / 2242