Instruction Manual
Table Of Contents
- 1. General
- 2. Installation
- 2.1 Installing power source mains plug
- 2.2 Installing cooling unit (optional)
- 2.3 Installing equipment on cart (optional)
- 2.4 Connecting welding gun
- 2.5 Installing earth return cable
- 2.6 Installing remote control (optional)
- 2.7 Installing and replacing feed rolls
- 2.8 Installing and replacing wire guide tubes
- 2.9 Installing and changing wire
- 2.10 Installing gas bottle and testing gas flow
- 2.11 How to get welding programs
- 3. Operation
- 3.1 Preparing welding system for use
- 3.2 Calibrating welding cable
- 3.3 Using control panel
- 3.3.1 Control panel: Home view
- 3.3.2 Control panel: Weld Assist
- 3.3.3 Control panel: Channels
- 3.3.4 Control panel: WPS view
- 3.3.5 Control panel: Welding parameters
- 3.3.6 Control panel: Weld history
- 3.3.7 Control panel: Info view
- 3.3.8 Control panel: Device settings
- 3.3.9 Control panel: Applying welding programs
- 3.3.10 Control panel: Weld data view
- 3.4 Additional guidance to functions and features
- 3.5 Pulse welding
- 3.6 Wireless connection (WLAN)
- 3.7 Using remote control
- 3.8 Changing welding polarity
- 3.9 Lifting equipment
- 4. Maintenance
- 5. Technical data
Master M 358
Operating manual - EN
1.1 Equipment description
Master M 358 device models (350 A)
• Master M 358 G
>> Generator-compatible
>> Pulse device with automatic 1-MIG and pulse processes. Advanced MAX processes as optional.
• Master M 358 GM
>> Generator-compatible and multi-voltage
>> Pulse device with automatic 1-MIG and pulse processes. Advanced MAX processes as optional.
Both Master M 358 device models have a 4-roll wire feed mechanism with the maximum wire spool diameter of 300 mm.
For the Master M 358 device part descriptions, refer to "Master M 358 device" on page7.
Master M 358 control panels
• 2-knob 5.7" TFT/LCD control panel
Master M cooling units
• Master M Cooler
• Master M Cooler MV (multi-voltage).
For the cooling unit part descriptions, refer to "Master M Cooler cooling unit (optional)" on page11.
MIG welding guns
• Flexlite GX welding guns with euro connector.
For more information on the Flexlite GX welding guns, refer to Kemppi Userdoc.
Subfeeders
Subfeeder support can be added with a separate installation kit (contact your Kemppi dealer / service workshop for
more information).
• SuperSnake GTX subfeeder
For more information on the SuperSnake GTX subfeeder, refer to
Kemppi Userdoc.
Welding programs
• Welding program work pack (factory-installed)
• 1-MIG Wise features: WiseSteel and WiseFusion
• 1-MIG Wise features: WisePenetration+ (on-demand / at the time of purchase)
• Additional 1-MIG and pulse welding programs (on-demand / at the time of purchase)
• Additional MAX processes (on-demand / at the time of purchase)
The welding programs included in the Master M work packs are shown here:"Welding program work packs" on page90.
For more information on acquiring welding programs and additional welding processes, contact your local Kemppi
dealer.
Optional accessories
• 4-wheel carts
• 2-wheel carts
• Remote control HR40 (2-knob control)
• Remote control HR43 (1-knob control)
• Wire feeder cabinet heater
• Power source air filter
© Kemppi
5
1921980 / 2242