User Manual
Table Of Contents
- Legal Notice
- Table of Contents
- About this Main Manual
- Rigs and Signal Chain
- Front Panel Controls Head, PowerHead, Rack, and PowerRack
- Chicken Head Knob (1)
- INPUT Button (2)
- INPUT LED (2)
- Module and Section Buttons (3)
- OUTPUT/MASTER Button (4)
- OUTPUT LED (4)
- NOISE GATE Knob (5)
- Direct Control Knobs (6)
- MASTER VOLUME Knob (7)
- TAP Button (8)
- SYSTEM Button (9)
- RIG Button (10)
- QUICK Button (11)
- TYPE Knob (12)
- BROWSE Knob (13)
- Soft Buttons and Soft Knobs (14)
- ON/OFF Button (15)
- LOCK Button (16)
- COPY and PASTE Buttons (17)
- STORE Button (18)
- UNDO and REDO Buttons (19)
- EXIT Button (20)
Buttons (21) - RIG Navigation Cross (22)
- HEADPHONE Output (23)
- GAIN Knob (24)
- RIG VOLUME Knob (25)
- Front INPUT (26)
- USB (27)
- Back Panel Overview Head, PowerHead, Rack, and PowerRack
- Front Panel Controls Stage
- On/Off Button (1)
- Mode Select Buttons (2)
- INPUT Button (3)
- INPUT LED (3)
- Module and Section Buttons (4)
- OUTPUT/MASTER Button (5)
- OUTPUT LED (5)
- MASTER VOLUME Knob (6)
- SYSTEM Button (7)
- PEDALS Button (8)
- RIG Button (9)
- TYPE Knob (10)
- BROWSE Knob (11)
- Soft Buttons and Soft Knobs (12)
- MORPH Button (13)
- LOCK Button (14)
- EDIT Button (15)
- COPY and PASTE Buttons (N/A)
- STORE Button (16)
- Button (17)
Buttons (18) - GAIN Knob (19)
- Up/Down Buttons (20)
- Rig Buttons 1-5 (21)
- TAP Button (22)
- TUNER Button (23)
- Effect Buttons I-IIII (24)
- Looper (25)
- Back Panel Overview Stage
- Basic Setups
- Using the Tuner
- Rig Settings
- Working with Amplifier PROFILEs, Cabinet PROFILEs, Power Amps and Guitar Cabinets
- Separating Amps and Cabinets: CabDriver
- Browsing Amps or Cabinets
- Direct PROFILEs
- Direct Amp PROFILEs
- Cabinet Impulse Responses
- Merging Studio PROFILEs and Direct Amp PROFILEs
- Running a Guitar Speaker Cabinet from a Power Amplifier, “Monitor Cab Off”
- The Built-in Power Amplifier
- The Sound of Guitar Cabinets versus Mic'ed Speakers
- PURE CABINET
- Output Section
- Instrument Input and Reamping
- Expression Pedals and Foot Switches
- Stack Section
- Effects
- Wah Effects (Orange)
- Distortion (Red)
- Booster (Red)
- Shaper (Red)
- Equalizer (Yellow)
- Compressor (Cyan)
- Noise Gate (Cyan)
- Chorus (Blue)
- Phaser and Flanger (Purple)
- Pitch Shifter (White)
- Delay (Green)
- Delay Mix
- Mix Location Pre/Post
- Low Cut & High Cut
- Cut More
- To Tempo
- Delay Time & Delay Ratio
- Note Value
- Feedback
- Freeze
- Infinity
- Cross Feedback
- Reverse Mix
- Input Swell
- Smear
- Stereo
- Grit
- Stereo Modulation
- Flutter Intensity & Flutter Rate
- Single Delay
- Dual Delay
- Two Tap Delay
- Serial Two Tap Delay
- Rhythm Delay
- Quad Delay
- Legacy Delay
- Pitch Shifter Delay (Light Green)
- Reverb (Green)
- Effect Loop (Pink)
- System Settings
- Bass Players: Special Hints and Features
- Performance Mode
- PROFILER Remote
- MIDI
- Continuous Controllers
- Effect Switches
- Rig Change in Performance Mode
- Rig Change in Browser Mode
- MIDI Global Channel
- MIDI Clock
- Transmitting MIDI Commands to Two External Devices in Performance Mode
- Transmitting Pedal Controllers for Morphing, Wah, Volume, and Pitch to Two External Devices
- Transmitting User Interface to MIDI Global Channel
- NRPN
- Getting Organized
- Updates, Backups and Sharing Sounds
- PROFILING an Amp
- Trouble Shooting
- KEMPER PROFILER Specifications
- Dimensions
- Weight
- Analog Inputs PROFILER Head, PowerHead, Rack, and PowerRack
- Analog Inputs PROFILER Stage
- Analog Outputs PROFILER Head, PowerHead, Rack, and PowerRack
- Analog Outputs PROFILER Stage
- Power Amp PROFILER PowerHead and PROFILER PowerRack
- Control and Data Interfaces
- Digital Inputs and Outputs PROFILER Head, PowerHead, Rack, and PowerRack
- Digital Inputs and Outputs PROFILER Stage
- Electrical Requirements
- Environmental Requirements
- Electrical Approvals
Front Panel Controls Stage 49
OUTPUT LED (5)
The PROFILER performs soft clipping and is very forgiving in terms of amplitude clipping, so here is no need to
panic if the OUTPUT LED flashes red occasionally. Typically, you might experience this with clean sounds. In such
cases you could either decrease Rig Volume or another Volume in the Rig e. g. Amplifier Volume, or perhaps
consider enhancing your clean Rig with a Compressor effect.
MASTER VOLUME Knob (6)
Master Volume is the master of all output volumes and is always global. It is not stored as part of any Rig. Changing
the volume will not affect the color of the sound.
Volumes of all analog outputs including the HEADPHONE output are linked to Master Volume by default. These links
can be activated and deactivated with soft buttons in the Output Section (e. g. “Headphone Link”).
Master Volume maintains the relative volume settings of all outputs linked to it. For example, if MONITOR OUTPUT
Volume is set relatively low and Main Output Volume relatively high, and both are linked to Master Volume, you
might need to crank up Master Volume quite a bit before the MONITOR OUTPUT will send a signal. In an extreme
case, one output could still be dead even with Master Volume at maximum. Please use the individual volume
controls in the Output Section to balance their levels according to your needs. As a rule, it’s best to avoid extreme
volume differences between any of the outputs linked to Master Volume.
As output volumes of linked outputs might vary, Master Volume doesn’t follow a dB scale, but a simple 0-10 scale.
MASTER VOLUME offers a LED collar, which reflects the volume of one output. You can select this output in
System Settings with “Volume LED Collar”.