User Manual
Table Of Contents
- Legal Notice
- Table of Contents
- About this Main Manual
- Rigs and Signal Chain
- Front Panel Controls Head, PowerHead, Rack, and PowerRack
- Chicken Head Knob (1)
- INPUT Button (2)
- INPUT LED (2)
- Module and Section Buttons (3)
- OUTPUT/MASTER Button (4)
- OUTPUT LED (4)
- NOISE GATE Knob (5)
- Direct Control Knobs (6)
- MASTER VOLUME Knob (7)
- TAP Button (8)
- SYSTEM Button (9)
- RIG Button (10)
- QUICK Button (11)
- TYPE Knob (12)
- BROWSE Knob (13)
- Soft Buttons and Soft Knobs (14)
- ON/OFF Button (15)
- LOCK Button (16)
- COPY and PASTE Buttons (17)
- STORE Button (18)
- UNDO and REDO Buttons (19)
- EXIT Button (20)
Buttons (21) - RIG Navigation Cross (22)
- HEADPHONE Output (23)
- GAIN Knob (24)
- RIG VOLUME Knob (25)
- Front INPUT (26)
- USB (27)
- Back Panel Overview Head, PowerHead, Rack, and PowerRack
- Front Panel Controls Stage
- On/Off Button (1)
- Mode Select Buttons (2)
- INPUT Button (3)
- INPUT LED (3)
- Module and Section Buttons (4)
- OUTPUT/MASTER Button (5)
- OUTPUT LED (5)
- MASTER VOLUME Knob (6)
- SYSTEM Button (7)
- PEDALS Button (8)
- RIG Button (9)
- TYPE Knob (10)
- BROWSE Knob (11)
- Soft Buttons and Soft Knobs (12)
- MORPH Button (13)
- LOCK Button (14)
- EDIT Button (15)
- COPY and PASTE Buttons (N/A)
- STORE Button (16)
- Button (17)
Buttons (18) - GAIN Knob (19)
- Up/Down Buttons (20)
- Rig Buttons 1-5 (21)
- TAP Button (22)
- TUNER Button (23)
- Effect Buttons I-IIII (24)
- Looper (25)
- Back Panel Overview Stage
- Basic Setups
- Using the Tuner
- Rig Settings
- Working with Amplifier PROFILEs, Cabinet PROFILEs, Power Amps and Guitar Cabinets
- Separating Amps and Cabinets: CabDriver
- Browsing Amps or Cabinets
- Direct PROFILEs
- Direct Amp PROFILEs
- Cabinet Impulse Responses
- Merging Studio PROFILEs and Direct Amp PROFILEs
- Running a Guitar Speaker Cabinet from a Power Amplifier, “Monitor Cab Off”
- The Built-in Power Amplifier
- The Sound of Guitar Cabinets versus Mic'ed Speakers
- PURE CABINET
- Output Section
- Instrument Input and Reamping
- Expression Pedals and Foot Switches
- Stack Section
- Effects
- Wah Effects (Orange)
- Distortion (Red)
- Booster (Red)
- Shaper (Red)
- Equalizer (Yellow)
- Compressor (Cyan)
- Noise Gate (Cyan)
- Chorus (Blue)
- Phaser and Flanger (Purple)
- Pitch Shifter (White)
- Delay (Green)
- Delay Mix
- Mix Location Pre/Post
- Low Cut & High Cut
- Cut More
- To Tempo
- Delay Time & Delay Ratio
- Note Value
- Feedback
- Freeze
- Infinity
- Cross Feedback
- Reverse Mix
- Input Swell
- Smear
- Stereo
- Grit
- Stereo Modulation
- Flutter Intensity & Flutter Rate
- Single Delay
- Dual Delay
- Two Tap Delay
- Serial Two Tap Delay
- Rhythm Delay
- Quad Delay
- Legacy Delay
- Pitch Shifter Delay (Light Green)
- Reverb (Green)
- Effect Loop (Pink)
- System Settings
- Bass Players: Special Hints and Features
- Performance Mode
- PROFILER Remote
- MIDI
- Continuous Controllers
- Effect Switches
- Rig Change in Performance Mode
- Rig Change in Browser Mode
- MIDI Global Channel
- MIDI Clock
- Transmitting MIDI Commands to Two External Devices in Performance Mode
- Transmitting Pedal Controllers for Morphing, Wah, Volume, and Pitch to Two External Devices
- Transmitting User Interface to MIDI Global Channel
- NRPN
- Getting Organized
- Updates, Backups and Sharing Sounds
- PROFILING an Amp
- Trouble Shooting
- KEMPER PROFILER Specifications
- Dimensions
- Weight
- Analog Inputs PROFILER Head, PowerHead, Rack, and PowerRack
- Analog Inputs PROFILER Stage
- Analog Outputs PROFILER Head, PowerHead, Rack, and PowerRack
- Analog Outputs PROFILER Stage
- Power Amp PROFILER PowerHead and PROFILER PowerRack
- Control and Data Interfaces
- Digital Inputs and Outputs PROFILER Head, PowerHead, Rack, and PowerRack
- Digital Inputs and Outputs PROFILER Stage
- Electrical Requirements
- Environmental Requirements
- Electrical Approvals
PROFILING an Amp 280
Connections for PROFILING a Combination of Amp and Stomp Box
Connections including a stomp box; on PROFILER Stage connect to SEND 1 and RETURN 1
• Connect your guitar to the INPUT of the PROFILER.
• Connect the DIRECT OUTPUT or SEND 1 from the PROFILER to the input of your stomp box.
• Connect the output of the stomp box to the input of your reference amplifier.
• Connect the microphone or microphone preamp to the RETURN or RETURN 1 of the PROFILER.