User Manual
Table Of Contents
- Legal Notice
- Table of Contents
- About this Main Manual
- Rigs and Signal Chain
- Front Panel Controls Head, PowerHead, Rack, and PowerRack
- Chicken Head Knob (1)
- INPUT Button (2)
- INPUT LED (2)
- Module and Section Buttons (3)
- OUTPUT/MASTER Button (4)
- OUTPUT LED (4)
- NOISE GATE Knob (5)
- Direct Control Knobs (6)
- MASTER VOLUME Knob (7)
- TAP Button (8)
- SYSTEM Button (9)
- RIG Button (10)
- QUICK Button (11)
- TYPE Knob (12)
- BROWSE Knob (13)
- Soft Buttons and Soft Knobs (14)
- ON/OFF Button (15)
- LOCK Button (16)
- COPY and PASTE Buttons (17)
- STORE Button (18)
- UNDO and REDO Buttons (19)
- EXIT Button (20)
Buttons (21) - RIG Navigation Cross (22)
- HEADPHONE Output (23)
- GAIN Knob (24)
- RIG VOLUME Knob (25)
- Front INPUT (26)
- USB (27)
- Back Panel Overview Head, PowerHead, Rack, and PowerRack
- Front Panel Controls Stage
- On/Off Button (1)
- Mode Select Buttons (2)
- INPUT Button (3)
- INPUT LED (3)
- Module and Section Buttons (4)
- OUTPUT/MASTER Button (5)
- OUTPUT LED (5)
- MASTER VOLUME Knob (6)
- SYSTEM Button (7)
- PEDALS Button (8)
- RIG Button (9)
- TYPE Knob (10)
- BROWSE Knob (11)
- Soft Buttons and Soft Knobs (12)
- MORPH Button (13)
- LOCK Button (14)
- EDIT Button (15)
- COPY and PASTE Buttons (N/A)
- STORE Button (16)
- Button (17)
Buttons (18) - GAIN Knob (19)
- Up/Down Buttons (20)
- Rig Buttons 1-5 (21)
- TAP Button (22)
- TUNER Button (23)
- Effect Buttons I-IIII (24)
- Looper (25)
- Back Panel Overview Stage
- Basic Setups
- Using the Tuner
- Rig Settings
- Working with Amplifier PROFILEs, Cabinet PROFILEs, Power Amps and Guitar Cabinets
- Separating Amps and Cabinets: CabDriver
- Browsing Amps or Cabinets
- Direct PROFILEs
- Direct Amp PROFILEs
- Cabinet Impulse Responses
- Merging Studio PROFILEs and Direct Amp PROFILEs
- Running a Guitar Speaker Cabinet from a Power Amplifier, “Monitor Cab Off”
- The Built-in Power Amplifier
- The Sound of Guitar Cabinets versus Mic'ed Speakers
- PURE CABINET
- Output Section
- Instrument Input and Reamping
- Expression Pedals and Foot Switches
- Stack Section
- Effects
- Wah Effects (Orange)
- Distortion (Red)
- Booster (Red)
- Shaper (Red)
- Equalizer (Yellow)
- Compressor (Cyan)
- Noise Gate (Cyan)
- Chorus (Blue)
- Phaser and Flanger (Purple)
- Pitch Shifter (White)
- Delay (Green)
- Delay Mix
- Mix Location Pre/Post
- Low Cut & High Cut
- Cut More
- To Tempo
- Delay Time & Delay Ratio
- Note Value
- Feedback
- Freeze
- Infinity
- Cross Feedback
- Reverse Mix
- Input Swell
- Smear
- Stereo
- Grit
- Stereo Modulation
- Flutter Intensity & Flutter Rate
- Single Delay
- Dual Delay
- Two Tap Delay
- Serial Two Tap Delay
- Rhythm Delay
- Quad Delay
- Legacy Delay
- Pitch Shifter Delay (Light Green)
- Reverb (Green)
- Effect Loop (Pink)
- System Settings
- Bass Players: Special Hints and Features
- Performance Mode
- PROFILER Remote
- MIDI
- Continuous Controllers
- Effect Switches
- Rig Change in Performance Mode
- Rig Change in Browser Mode
- MIDI Global Channel
- MIDI Clock
- Transmitting MIDI Commands to Two External Devices in Performance Mode
- Transmitting Pedal Controllers for Morphing, Wah, Volume, and Pitch to Two External Devices
- Transmitting User Interface to MIDI Global Channel
- NRPN
- Getting Organized
- Updates, Backups and Sharing Sounds
- PROFILING an Amp
- Trouble Shooting
- KEMPER PROFILER Specifications
- Dimensions
- Weight
- Analog Inputs PROFILER Head, PowerHead, Rack, and PowerRack
- Analog Inputs PROFILER Stage
- Analog Outputs PROFILER Head, PowerHead, Rack, and PowerRack
- Analog Outputs PROFILER Stage
- Power Amp PROFILER PowerHead and PROFILER PowerRack
- Control and Data Interfaces
- Digital Inputs and Outputs PROFILER Head, PowerHead, Rack, and PowerRack
- Digital Inputs and Outputs PROFILER Stage
- Electrical Requirements
- Environmental Requirements
- Electrical Approvals
PROFILER Remote 241
Up/Down Buttons (1)
In Performance Mode, use these buttons to navigate through your Performances. A short tap will step up or down to
the next Performance. Holding will initiate scrolling. Depending on the status of the parameter "Performance Load" in
the System Settings, the PROFILER will either load Slot 1 or the current Slot of the selected Performance
immediately, or wait (“Pending”) until you hit one of the five Rig Buttons.
In Browser Mode, you can step or scroll through Rigs in your browse pool according to the selected View and Sort
Order criteria. The option “Group of 5/Single Rig” on page Remote Settings in System Settings determines, if the
Up/Down Buttons step through the Rigs individually or by groups of five in Browser Mode.
✓ The function of the Up/Down Buttons can be changed on the “Remote Buttons” page in System Settings, reached
via “Button Assignment” on the Remote Settings page.
✓ Users of the PROFILER Stage can find identical settings on the User Interface 2 page in System Settings.
Rig Buttons 1-5 (2)
These are the buttons for selecting Slots in Performance Mode, and Rigs in Browser Mode. Subsequent hits of these
buttons trigger Morphing.
TAP Button (3)
This button triggers the Tap Tempo, just like the TAP button on the front panel of the PROFILER Head and Rack
models. Tap in quarter notes to adjust the tempo of delay, phaser, flanger, and tremolo effects. The LED will blink to
indicate the current tempo. Holding this button while you play to activate the marvelous Beat Scanner, which