User's Manual
Table Of Contents
- KH1264 ISSUE 1
- CHAPTER 1
- CHAPTER 2
- CHAPTER 3
- CONTENTS
- ILLUSTRATIONS
- Figure 1 - Transceiver (DTX-A3): Module Locations 34
- Figure 2 - Drive Control Unit (GTX-A24): Module Locations 35
- Figure 3 X-band Upmast Transceiver (DTX-A3): Functional Diagram Figure 3 38
- Figure 4 X-band Upmast Transceiver (DTX-A3): Interconnection Diagram Figure 4 39
- Figure 5 - Drive Control Unit (GTX-A24): Block Diagram 319
- CHAPTER 4
- CONTENTS
- TABLES
- ILLUSTRATIONS
- Figure 1 - Transceiver (DTX-A3): Installation Dimensions 49
- Figure 2 - Transceiver (DTX-A3): Mast Mounting 410
- Figure 3 - Transceiver (DTX-A3): Fitting Kit 411
- Figure 4 - Suggested Antenna Lifting Arrangement 412
- Figure 5 - Drive Control Unit (GTX-A24): Installation Dimensions 413
- Figure 6 - Mains Isolator: Installation Dimensions 414
- Figure 7 - Transceiver (DTX-A3): Cableform Routing 419
- Figure 8 - Drive Control Unit (GTX-A24): Cableform Routing 420
- Figure 9 - Cable Gland: Assembly 421
- Figure 10 - Transceiver (DTX-A3): External Connections 423
- CHAPTER 5
- CHAPTER 6
- CONTENTS
- INTRODUCTION 63
- PLANNED MAINTENANCE 63
- DIAGNOSTIC MAINTENANCE 64
- CORRECTIVE MAINTENANCE 611
- TRANSCEIVER (DTX-A3) 612
- Access 612
- Removal of Rotating Joint (45-750-0034-001) 612
- Replacement of Rotating Joint (45-750-0034-001) 613
- Removal of Gearbox and Motor (55-100-0273-001) 613
- Replacement of Gearbox and Motor (55-100-0273-001) 613
- Removal of Azimuth Encoder (GTX-A188) 613
- Replacement of Azimuth Encoder (GTX-A188) 613
- Transceiver (DTX-A115) - Removal 614
- Transceiver (DTX-A115) - Replacement 614
- Power Supply (45-690-0062-002) and PSU Sense PCB (DTX-A121) - Removal 615
- Power Supply (45-690-0062-002) and PSU Sense PCB (DTX-A121) - Replacement 615
- CAN Adapter PCB (NNR-A981) - Removal 615
- CAN Adapter PCB (NNR-A981) - Replacement 615
- SharpEye Azimuth Interface PCB (DTX-A151) - Removal 616
- SharpEye Azimuth Interface PCB (DTX-A151) - Replacement 616
- DRIVE CONTROL UNIT (GTX-A24) 618
- CHECKS AFTER UNIT REPLACEMENT 620
- TRANSCEIVER (DTX-A3) 612
- ILLUSTRATIONS
- CONTENTS
- CHAPTER 7
- INSTALLATION AND SERVICE REPORTS
KH1264
Chap ter 4
Is sue 2 Page 4.11
ISOMETRIC VIEW
( 1 : 2 )
SIDE VIEW
1
1
2
2
3
3
4
4
5
5
6
6
A A
B B
C C
D D
USED ON
BY
DRAWN
PROJECTION
DO NOT SCALE
M/C
SCALE
DEPT
MATERIAL
HOLES OVER 6mm TO BS4500 H13
TWO DECIMAL PLACES 0.15
ONE DECIMAL PLACE 0.5
NO DECIMAL PLACE 1.0
1
DIMENSIONAL
HOLE DIA UP TO 6mm TO BS4500 H11
SCREW THREADS
OTHERWISE STATED
TOLERANCES UNLESS
INTERNAL
EXTERNAL
COARSE PITCH
CLASS 6H
CLASS 6g
BS 3643
?
FINISH
KELVIN HUGHES
A part of Smiths Aerospace - Marine System
Drawing No
TITLE
KELVIN HUGHES
NAME
Contd On
ISSUE
CR NOTE
Kelvin Hughes Ltd 2007
This document is the property of
Sheet No
?
?
??
?
?
ANGULAR
?
DRAWING PRACTICE TO BS 8888
DATE
THIRD ANGLE
A3
GTX-A144
TCH
GTX-A16
T.Hannington
FITTING KIT
MANTA S BAND
A
06/12/2005
1:2
-
1
COMM
GTX-A11
DTX-A1
TCH
3
18/10/2006 CR7698
JJS
JJS
1
2
05/07/2006
28/06/2006
CR7528
DR1365
TCH
4
17/10/2007 CO10950
B
TCH 28/06/2006
Parts List
TITLEPART NUMBER
QTY
ITEM
WASHER CRINKLE M8
20-282-5011-2511
WASHER PLAIN M8
25-238-0024-00122
WASHER PLAIN M16 EX-LARGE
25-238-0027-00183
SCREW HEX HD M8 X 35 LG ST STEEL25-252-1223-271
4
HEX NUT FULL M8 STN STL
25-271-3069-271
5
SELF LOCKING NUT M16 ST SL (A4)
25-273-0006-00146
BOLT HEX HD M16 X 100 LG BS970-A2
ZINC PLATE & PASS
45-280-0025-0014
7
SHIM 1MM THKCAE-1189
38
COLLAR NOISE ISOLATION M16X27GTX-1203
4
9
DISC NOISE ISOLATION M16GTX-1204
810
BOX RIGID TYPE 'D' (200x150x50)
PP-6013111
COUPLING ELEMENT W/GUIDE
ZV-9758112
NUT M16 NYLOC
25-273-0006-001
WASHER M16 EX. LARGE
25-238-0027-001
SHIM (OPTIONAL)
CAE-1189
TICO WASHER
M16x60x12.5
GTX-1204
TICO COLLAR M16x27GTX-1203
BOLT M16x100
BS 970-A2
45-280-0025-001
FOOT
DECK
USE SHIM(S) (AGAINST DECK) TO ADJUST FOR UN-EVEN SURFACE
TIGHTEN BOLT TO
SPECIFIED TORQUE
SEE NOTE 2
WASHER M16 EX. LARGE
25-238-0027-001
TICO WASHER
M16X60X12.5
GTX-1204
NOTES
1. ALL ITEMS ARE TO BE FITTED INTO BOX PP-6013
TOGETHER WITH A COPY OF THIS DRAWING.
2. BOLTS TO BE TIGHTENED TO A TORQUE OF 20 NM
OR TO PRODUCE A SMALL DEFLECTION IN THE
UPPER TICO WASHER.
MOUNTING PLATE
USE SHIM(S) (AGAINST
DECK) TO ADJUST FOR
UNEVEN SURFACE
TICO COLLAR M16 x 27
GTX-1203
Figure 3 - Transceiver (DTX-A3): Fitting Kit