Assembly Instruction

ManualsBrandsKelly Clarkson Home ManualsFurnitureClare 3 - Light Caged Drum Semi Flush Mount

1of2

(3)B10CandelabraBasebulbs60WMaximum.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

LightSource:

EstimatedAssemblyTime:

Preparation:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Package Contents

Crossbar

Assembly

Mounting Screw

Hex Nut and

Lock Washer

Mounting Ball

Figure 3

Fixture

Body

Ceiling Canopy

with Nipple

Spacer Tube

STEP 1 Install Spacer Tube and Ceiling Canopy-

A. Pass the supply wires and ground wire from fixture through the

Spacer Tube (C) and the Ceiling Canopy with Nipple (B) in turn.

Place the nipple of the Ceiling Canopy with Nipple (B) through the

Spacer Tube (C) and thread the nipple onto the hex coupling on the

top center of the Fixture Body (D). Hand tighten until snug.

Figure 1

Hex Coupling

Supply Wires

with Ground Wire

STEP 2 - Installing the Crossbar Assembly

A. Pass the supply wires with ground wire from outlet box through the

Crossbar Assembly (A). Attach the Crossbar Assembly (A) to the

Outlet Box with the head of the Green Ground Screw facing you.

Secure the Crossbar Assembly (A) with Outlet Box Screws (not

included). Tighten until snug.

Supply Wires

with Ground Wire

Figure 2

Outlet Box Screws

(not included)

Outlet Box

STEP 3 - Test Fit the Ceiling Canopy to the Crossbar Assembly

A. Remove the mounting balls from the Crossbar Assembly (A). Place

the ceiling canopy onto the Crossbar Assembly (A) and secure with

mounting balls. Note: The ceiling canopy should be snug against the

ceiling and held tight with the mounting balls. If it is not, adjust the

length of the mounting screws on the Crossbar Assembly (A) by

unscrewing the preassembled hex nut and lock washer and then

screwing the mounting screws in or out of the crossbar until the

correct length is achieved. Once the ceiling canopy is secure,

remove the mounting ball and fixture and proceed to Step 4.

Ceiling Canopy

Assembly Instruction Sheet

Summary of content (2 pages)

PAGE 1
Assembly Instruction Sheet Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (3) B10 Candelabra Base bulbs 60W Maximum. Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture.
PAGE 2
STEP 4 - Wire Connections A. Use standard wire connectors (not included) to make all wire connections. Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box. White wire from outlet box White wire from fixture Black wire from outlet box (or Red) Black wire from fixture Bare, or Green Ground wire from outlet box FINISH: CENTURY SILVER LEAF 5.5” Dia.