Manual

WARRANTY
This warranty is granted by Kel-Tec CNC
Industries, Inc. P.O. Box 236009, Cocoa, FL
32923. This lifetime warranty is effective from
the date of purchase and applies to the original
owner of a Kel-Tec PLR-16 pistol.
Kel-Tec firearms are warranted to be free from
defects in material and workmanship. Any
such defects of which Kel-Tec receives
written notice by the original owner, will be
remedied by Kel-Tec without charge within a
reasonable time after such notification and
delivery of the product as provided below.
Warranty claims (in writing) and the gun
concerned should be delivered (transportation
charges pre-paid) to:
Kel-Tec CNC, Inc
Service Department
1475 Cox Road
Cocoa, FL 32926.
No return authorization number is required. In
addition, a copy of a bill of sale in the owner’s
name, or a copy of ATF Form 4473, indicating
date of purchase must be included.
In order to expedite service, warranty claims
should state the model and serial number of the
gun concerned and a description of the
difficulty experienced. It is recommended that
shipments be insured by the owner, since Kel-
Tec will accept no responsibility for loss or
damage in transit.
Transportation and insurance charges for
return to owner will be paid by Kel-Tec if the
claim is covered by the warranty.
Under no circumstances shall Kel-Tec be
responsible for incidental or consequential
damages with respect to economic loss or
injury or property damage, whether as a result
of breach of express or implied warranty,
negligence or otherwise. Some states do not
allow the exclusion or limitation or incidental or
consequential damages, so the above limitation
or exclusion may not apply to you.
Kel-Tec will not be responsible for defects
resulting from careless handling, unauthorized
adjustments or modifications, defective or
improper ammunition, corrosion, neglect,
abuse, ordinary wear and tear, or unreason-
able use.
the firing pin pin, solvents can damage the O-
ring used to hold it in place. Thoroughly dry all
parts. Apply a light coat of oil to the firing pin,
bolt, cam pin and the surfaces in the bolt
carrier where the bolt, cam pin, and firing pin
slide. Apply a light coat of oil on the piston rod
and assemble the bolt carrier assembly and
pistol as stated in the assembly part of this
manual. Manually cycle the bolt back and forth
to check the function of the pistol. If any parts
are damaged or badly worn or the pistol does
not work correctly the pistol should not be fired
and should be returned to Kel-Tec for servicing
immediately.
LUBRICATION WARNING:
Firing a pistol with oil, grease, or any
other material even partially obstructing
the bore may damage the pistol and
injure the shooter and those nearby.
Do not spray or apply lubricants directly
on ammunition. If the powder charge of
a cartridge is affected by the lubricant, it
may not be ignited, but the energy from
the primer may be sufficient to push the
bullet into the bore where it may
become lodged. Firing a subsequent
bullet into the obstructed bore will
damage the pistol and may injure the
shooter and bystanders. Use lubricants
properly. You are responsible for the
proper care and maintenance of your
firearm.
WARNING:
It is not recommended that you disas-
semble the grip of the PLR-16 pistol; the
hammer spring is constantly under
tension and can easily injure you or
others. If the need arises to lubricate
the trigger assembly do so through the
access slot behind and in front of the
hammer.
Service
Should your PLR-16 pistol require adjustment,
refinishing, or repair, it should be returned
unloaded to the factory. In shipping the PLR-16
pistol, be sure to adhere to the following rules:
Individuals who wish to return the firearm for
service can do so by shipping via UPS prepaid.
No return authorization number is required.
Include a letter of instruction, full name,
address, phone number and the gun’s serial
number. This will insure prompt service and
handling. Once your pistol has been received,
anything other than warranty work, you will
receive a quotation. You will be notified of full
charges and no work will commence before
receiving your approval of our quotation. Also
see Warranty Page for further instructions.
All quotations are payable by C.O.D., VISA,
M.C. or money orders only. No personal checks
accepted. Please return your PLR-16 pistol to:
Kel-Tec CNC, Inc. Service Dept.
1475 Cox Road
Cocoa FL 32926