Datasheet

Datasheet
TEK.COM38
The 7711 plug-in module provides an economical, wideband signal
routing solution that complements the DC/low frequency switching
and measurement capability of the Integra Series systems. The 7711
offers dual 1×4 configurations and can interface with a wide range of
external AC instruments, including oscilloscopes, pulse generators,
and signal analysis tools. One channel in each multiplex bank is
always closed to the corresponding OUT connector. All connections
are easily accessible from the rear panel.
Key Features
Signal routing performance to 2 GHz
Switches up to 60 VDC
Rear panel SMA connections
Onboard switch closure counter
Onboard S parameter storage
Series 7700 Plug-In Switch Modules
Typical Insertion Loss
0 dB
–1 dB
–2 dB
–3 dB
–4 dB
10 100 1000 2000
Frequency (MHz)
Typical VSWR
1.8
1.6
1.4
1.2
1.0
10 1001 000 2000
Frequency (MHz)
7711 2 GHz 50 Ω RF Module
Datasheet
Specifications
Inputs (Channels 18)
Maximum Signal Level
Any channel to any channel or chassis (1–8):
30 Vrms (42 V peak for AC waveforms) or 60 VDC,
0.5 A.
Maximum Power 20 W per module, 10 W per channel (refer to
7711/7712 Manual PA-818 for meas ure ment
considerations).
Isolation Multiplexer to Multiplexer: >1 G Ω.
Center to Shield: >1 G Ω, <25 pF.
Channel to Channel: >10 0 M Ω.
Contact Life 1×10
6
no load, 1×10
5
rated load (resistive load).
Contact Potential <6 μV.
Contact Resistance <0.5 Ω (initial), <1 Ω (end of life).
Rise Time <300 ps (guaranteed by design).
Signal Delay <3 ns.
General
Relay Type High frequency electromechanical.
Contact Configuration
Dual 1×4 multiplexer, single pole four throw, Channels
1 and 5 are normally closed. Note: One channel
in each multiplex bank is always closed to the
corresponding OUT connector.
Close Channel ROUTe:CLOSe allows a single channel in a multiplex
bank to be closed. ROUTe:MULTiple:CLOSe allows
two channels (one in each bank) to be closed at one
time.
Open Channel ROUTe:OPEN:ALL closes CH1 and CH5 to OUT A and
OUT B respectively.
Actuation Time <10 ms.
Connector Type Ten external rear panel SMA connectors.
Mating Torque 0.9 N·m (8 in-lb).
Environmental Operating Environment: Specified for 0° to 50°C.
Specified to 80% R.H. at 35°C.
Storage Environment:25° to 6C.
EMC: Conforms to European Union EMC Directive.
Safety: Conforms to European Union Low Voltage
Directive
RoHS: Conforms to European Union RoHS Directive
Warranty: 1 year
Weight 0.5 kg (1.1 lb).
Available Accessories
7051-2 BNC Cable, male to male, 0.6 m (2 ft.)
7051-5 BNC Cable, male to male, 1.5 m (5 ft.)
7051-10 BNC Cable, male to male, 3.0 m (10 ft.)
7711-BNC-SMA Male SMA to female BNC Cables (5), 0.15 m (0.5 ft)
7712-SMA-1 SMA Cable, male to male, 1 m (3.3 ft)
7712-SMA-N Female SMA to Male N-Type Adapter
S46-SMA-0.5 SMA Cable, male to male, 0.15 m (0.5 ft.)
S46-SMA-1 SMA Cable, male to male, 0.3 m (1 ft.)
S46-SMA-1.7 SMA Cable, Male to Male, 0.58 m (1.7 ft)
Available Services
7711-3Y-EW 1-year factory warranty extended to 3 years from date
of shipment
Ordering Information
7711 2 GHz 50 Ω RF Module