Evolution3 FreeHand User Guide The world’s finest cutting machines www.keencut.com +44 (0) 1536 263158 +1 (716) 748 6203 sales@keencut.co.uk (UK HQ) sales@keencut.
Evolution3 FreeHand User Guide Contents 1. Introduction ......................................................................................................................................................... 3 1.1 The Evolution3 FreeHand user guide ........................................................................................................................ 3 2. Get to know your cutter ...............................................................................................................
Evolution3 FreeHand User Guide 1. Introduction 1.1 The Evolution3 FreeHand user guide This User Guide for the Evolution3 FreeHand gives advice on cutting techniques, using the different cutting heads and care and maintenance of your machine. Before using your machine make sure that you have installed and calibrated it correctly. Full details are in the Installation Manual. Visit the Evolution3 FreeeHand installation manual > The world’s finest cutting machines www.keencut.
Evolution3 FreeHand User Guide 2. Get to know your cutter 2.1 Swapping tool heads See how to swap tool heads in this video > Pull and remove end stop. Slide the cutting head to the right. The world’s finest cutting machines www.keencut.com +44 (0) 1536 263158 +1 (716) 748 6203 sales@keencut.co.uk (UK HQ) sales@keencut.
Evolution3 FreeHand User Guide Lift up the head to remove it. Insert the cutting head of your choice, and slide it to the left. More than one tool can be mounted on the cutter bar if required. Always replace the end stop. The world’s finest cutting machines www.keencut.com +44 (0) 1536 263158 +1 (716) 748 6203 sales@keencut.co.uk (UK HQ) sales@keencut.
Evolution3 FreeHand User Guide 3. Make your first cut 3.1 Align and clamp the material IMPORTANT: You must use a cutting mat for any cutting, creasing, or scoring process to prevent damage to the work surface. See how to align and clamp the material in this video > Place the cutting mat (A) on the work surface then the material to be cut (B) making sure the whole length of the cut line is over the cutting mat. Place the FreeHand on the material near to the cutline.
Evolution3 FreeHand User Guide 3.2 Introduction to the Double Graphik tool head See how to use the Double Graphik tool head in this video > QuikSwap Graphik tool head for Evolution3 cutters, with two individual blade holders for two way cutting. Graphik blades are stronger and more stable than regular blades. Ideal for vinyl, banner, cardboard, PVC foamboard up to 13mm (½″), foamcentred board, corrugated plastic, paper, pop-up and roll-up materials.
Evolution3 FreeHand User Guide 3.3 Insert Graphik blades into the Double Graphik tool head Undo the highlighted knob to remove the magnetic blade clamping plate. Pull the magnetic blade clamping plate away from the cutting head. Insert a Graphik blade, check it is facing the correct way for your desired direction of cutting. Place the small pin in the hole at the top of the blade and align with the edge of the clamping plate. The world’s finest cutting machines www.keencut.
Evolution3 FreeHand User Guide Replace the blade clamping plate onto the blade holder but do not tighten fully until the blade depth has been set (see how to adjust the blade depth >). Repeat on the other blade holder if required. The world’s finest cutting machines www.keencut.com +44 (0) 1536 263158 +1 (716) 748 6203 sales@keencut.co.uk (UK HQ) sales@keencut.
Evolution3 FreeHand User Guide 3.4 Double Graphik tool head cutting technique IMPORTANT: You must use a cutting mat for any cutting, creasing, or scoring process to prevent damage to the work surface Place the cutting mat (A) on the work surface then the material to be cut (B) making sure the whole length of the cut line is over the cutting mat. Place the FreeHand on the material near to the cutline.
Evolution3 FreeHand User Guide The cutting head can be pulled or pushed to cut the material. Load and align the material to be cut as described in the ‘clamping material’ section (see how to align and clamp the material >), press down the chosen blade holder whilst pushing/pulling the cutting head along the cutter bar. Tip: Only finger pressure is needed to hold the blade holder down, if after making the cut the blade holder has risen and the blade not cut through simply cut again.
Evolution3 FreeHand User Guide 3.5 Using a cutting station See how to create a cutting station > This process assumes a cutting groove has been made or the work surface has been covered with a cutting mat or other plastic material to act as a cutting mat. Lift the FreeHand and place it on the back of the two blocks to hold it above the work surface. Slide material to be cut under the FreeHand so that the cut position on the material is this side of the cutting line/groove on the work surface.
Evolution3 FreeHand User Guide Slide the material and the FreeHand back into the cutting position between the two blocks. Hold down the cutter bar and make the cut. The world’s finest cutting machines www.keencut.com +44 (0) 1536 263158 +1 (716) 748 6203 sales@keencut.co.uk (UK HQ) sales@keencut.
Evolution3 FreeHand User Guide 4. Using the Double Graphik tool head 4.1 Change the Graphik blades Undo the highlighted knob to remove the magnetic blade clamping plate. Pull the magnetic blade clamping plate away from the cutting head. Lift off the blunt blade (if there is one) and replace with a new Graphik blade, check it is facing the correct way for your desired direction of cutting. Place the small pin in the hole at the top of the blade and align with the edge of the clamping plate.
Evolution3 FreeHand User Guide Replace the blade clamping plate onto the blade holder but do not tighten fully until the blade depth has been set. Repeat on the other blade holder if required. The world’s finest cutting machines www.keencut.com +44 (0) 1536 263158 +1 (716) 748 6203 sales@keencut.co.uk (UK HQ) sales@keencut.
Evolution3 FreeHand User Guide 4.2 Adjust the blade depth and direction To adjust the height of the blade, loosen knob ‘A’ by a half to one full turn. Move knob ‘B’ up or down until the blade is long enough to just cut through the material. Place a piece of the material under the cutter bar so it does not protrude past the edge of the cutter bar and the blade can be seen against the edge of the material. Tighten ‘A’ to lock the blade in chosen position.
Evolution3 FreeHand User Guide The blades also have adjustable cutting depth, so if a thick material is being cut on a long machine such that it is beneficial to make two cuts, one blade can be set to cut half the thickness in one direction and the other to cut full depth on the return journey. The world’s finest cutting machines www.keencut.com +44 (0) 1536 263158 +1 (716) 748 6203 sales@keencut.co.uk (UK HQ) sales@keencut.
Evolution3 FreeHand User Guide 4.3 Advanced cutting techniques NOTE: The following is for a right-handed person. For left-handed use cut at the left-hand end of the cutter and reverse the direction of cut and hand positions. IMPORTANT: You must use a cutting mat for any cutting, creasing, or scoring process to prevent damage to the work surface Place the cutting mat (A) on the work surface then the material to be cut (B) making sure the whole length of the cut line is over the cutting mat.
Evolution3 FreeHand User Guide When cutting thick, tough materials such as PVC foam board and fluted plastics such as Correx or Coroplast, set the blade depth so the blade tip protrudes only 1-2mm (1⁄16”) through the thickness of the board and cuts from left to right. Position the cutting head to start the cut, turn your body to face to the right and place the palm of your right hand on the cutting head. Take a firm grip on the cutter bar with your left hand.
Evolution3 FreeHand User Guide Cutting Aluminium Composite Panels is not recommended using the Graphik tool head. See how to cut ACP with the Rocker tool head > Thin materials such as paper and plastic films are easily cut but attention should be given to supporting the material at the beginning of the cut. Pressing down lightly on the edge of the material with your index finger or thumb will prevent the material creasing when the blade starts cutting.
Evolution3 FreeHand User Guide 5. Using the Fabric tool head 5.1 Change the Fabric tool head blade Loosen the clamping knob. Remove the blade cover. Remove the safety cover. The world’s finest cutting machines www.keencut.com +44 (0) 1536 263158 +1 (716) 748 6203 sales@keencut.co.uk (UK HQ) sales@keencut.
Evolution3 FreeHand User Guide Remove the blade and magnetic blade boss. There may be a number of clear plastic shims on the threaded shaft, ensure they are clean and in good condition. Separate the boss from the blade and inspect the boss for wear and clean off any debris. Dispose of the worn blade responsibly. Reassemble with a new blade. Do not over tighten the clamping knob, it is essential that the blade is allowed to rotate whilst cutting. The world’s finest cutting machines www.keencut.
Evolution3 FreeHand User Guide 5.2 Use the Fabric tool head with a cutting mat IMPORTANT: You must use a cutting mat for any cutting, creasing, or scoring process to prevent damage to the work surface. Place the cutting mat (A) on the work surface then the material to be cut (B) making sure the whole length of the cut line is over the cutting mat. Place the FreeHand on the material near to the cutline.
Evolution3 FreeHand User Guide 5.3 Adjust the Fabric tool head blade pressure Turn the highlighted screw to adjust the blade pressure (clockwise to reduce). When adjusting you will see the pressure indicator go up and down. The world’s finest cutting machines www.keencut.com +44 (0) 1536 263158 +1 (716) 748 6203 sales@keencut.co.uk (UK HQ) sales@keencut.
Evolution3 FreeHand User Guide 5.4 Use the Fabric tool head blade guard Rotate the red blade guard, using tab (B), to reveal or hide the blade. If it is difficult to rotate loosen the clamping knob (A) a little. Ensure it is adjusted correctly before cutting so the blade is just able to rotate without sideways movement. The world’s finest cutting machines www.keencut.com +44 (0) 1536 263158 +1 (716) 748 6203 sales@keencut.co.uk (UK HQ) sales@keencut.
Evolution3 FreeHand User Guide 5.5 Fabric tool head cutting technique Take a small piece of the material to be cut, clamp it under the cutter bar. The Fabric tool head cuts in both directions and requires the blade holder to be pressed down fully whilst the rotary blade is cutting the material. Check the blade is rotating and not moving from side to side, if it is, adjust the blade clamping knob. The world’s finest cutting machines www.keencut.com +44 (0) 1536 263158 +1 (716) 748 6203 sales@keencut.co.
Evolution3 FreeHand User Guide Cut in one smooth continuous motion, adjust to increase or decrease the cutting pressure if necessary. When the small piece of material has been cut successfully place the main piece of fabric in the cutter, align and cut in the same way. NOTE: The Fabric tool head can also be used to cut many other thin materials such as paper and film. The world’s finest cutting machines www.keencut.com +44 (0) 1536 263158 +1 (716) 748 6203 sales@keencut.co.uk (UK HQ) sales@keencut.
Evolution3 FreeHand User Guide 6. Using the Creaser tool head 6.1 Different creasing wheels The three creasing wheels supplied with the Creaser tool head will each produce a different style of crease. Experiment on small samples of your material to see which gives best results. The world’s finest cutting machines www.keencut.com +44 (0) 1536 263158 +1 (716) 748 6203 sales@keencut.co.uk (UK HQ) sales@keencut.
Evolution3 FreeHand User Guide 6.2 Change the creasing wheels Remove the lower clamping knob. Remove the creasing wheel leaving the bearing and clear plastic shim in place. Remove the upper clamping knob. The world’s finest cutting machines www.keencut.com +44 (0) 1536 263158 +1 (716) 748 6203 sales@keencut.co.uk (UK HQ) sales@keencut.
Evolution3 FreeHand User Guide Choose the creasing wheel you would like to use and exchange it with the lower wheel. Replace both clamping knobs. The world’s finest cutting machines www.keencut.com +44 (0) 1536 263158 +1 (716) 748 6203 sales@keencut.co.uk (UK HQ) sales@keencut.
Evolution3 FreeHand User Guide 6.3 Creasing technique IMPORTANT: You must use a cutting mat for any cutting, creasing, or scoring process to prevent damage to the work surface. Place the cutting mat (A) on the work surface then the material to be cut (B) making sure the whole length of the cut line is over the cutting mat. Place the FreeHand on the material near to the cutline.
Evolution3 FreeHand User Guide Align your material in the machine, apply downward pressure to the wheel holder and move the cutting head along to create the crease line. Adjust the hand pressure and number of strokes accordingly, you can crease in either direction. The world’s finest cutting machines www.keencut.com +44 (0) 1536 263158 +1 (716) 748 6203 sales@keencut.co.uk (UK HQ) sales@keencut.
Evolution3 FreeHand User Guide 7. Using the Rocker tool head 7.1 The Rocker tool head The Rocker tool head has been especially designed to give perfect comfort for all day, every day, cutting. The tool head fits the curve of your hand, allowing you to cut denser materials with ease. The Rocker head accepts the Medium Duty blade and the specialist Tech D012 blade. IMPORTANT: it is not recommended to cut ACP using the FreeHand.
Evolution3 FreeHand User Guide 7.2 Fit or change the Rocker tool head blade To change the blade, loosen the blade clamping knob. Remove the magnetic cartridge from the Rocker head. Place the blade between the two guides, the magnet will hold it in place, and slide it back to touch the blade depth screw. The blade depth screw can be adjusted to set the blade correctly for the thickness of material to be cut.
Evolution3 FreeHand User Guide 7.3 Rocker tool head cutting technique IMPORTANT: it is not recommended to cut ACP using the FreeHand. To cut ACP with the Rocker tool head, it is recommended to use either the SmartFold or the BenchTop. IMPORTANT: You must use a cutting mat for any cutting, creasing, or scoring process to prevent damage to the work surface Place the cutting mat (A) on the work surface then the material to be cut (B) making sure the whole length of the cut line is over the cutting mat.
Evolution3 FreeHand User Guide When cutting thinner / less dense materials, ensure the blade depth is adjusted so only the tip of the blade is going through the material. Place your hand on the Rocker tool head as shown and rock it forward to engage the blade. With the blade engaged, pull the Rocker tool head in one continuous motion along the material to achieve the best results.
Evolution3 FreeHand User Guide Extra effort can be applied by holding the grip area on the top of the cutter bar with your other hand and using the strength across your shoulders to push. Thicker materials can be cut in several passes. IMPORTANT: it is not recommended to cut ACP using the FreeHand. To cut ACP with the Rocker tool head, it is recommended to use either the SmartFold or the BenchTop. The world’s finest cutting machines www.keencut.com +44 (0) 1536 263158 +1 (716) 748 6203 sales@keencut.co.
Evolution3 FreeHand User Guide 8. Care and maintenance 8.1 Clean your machine See how to clean your machine in this video > Use a vacuum cleaner to remove any dust and smaller debris. Frequency: daily as required Moisten a cloth with diluted detergent to wipe down the cutter bar and base plate, dry with a cloth. Frequency: weekly DO NOT use solvents or aggressive cleaning products. The world’s finest cutting machines www.keencut.com +44 (0) 1536 263158 +1 (716) 748 6203 sales@keencut.co.
Evolution3 FreeHand User Guide 8.2 Maintain the bearing track See how to maintain the bearing track in this video > Put a small amount of petroleum jelly (Vaseline) on the scouring surface of a dish washing sponge and rub it up and down the two tracks. Wipe clean any surplus with a dry cloth. Frequency: Light use – monthly Heavy use – weekly The world’s finest cutting machines www.keencut.com +44 (0) 1536 263158 +1 (716) 748 6203 sales@keencut.co.uk (UK HQ) sales@keencut.
Evolution3 FreeHand User Guide 8.3 Change the sightline strip IMPORTANT: Ensure that you have a replacement sightline strip before proceeding When using your FreeHand, the sightline strip may become scored or damaged. Remove any tool heads. Turn over the FreeHand so that the underside is visible. The world’s finest cutting machines www.keencut.com +44 (0) 1536 263158 +1 (716) 748 6203 sales@keencut.co.uk (UK HQ) sales@keencut.
Evolution3 FreeHand User Guide Remove the damaged sightline strip making sure that all residue from the adhesive tape is removed. NOTE: If you are struggling to remove any adhesive residue, lightly use methylated spirit on a paper towel or cloth. There is a yellow silicone grip strip fixed to the underside of the cutter bar, use this to help align the back edge of the replacement sightline strip. Remove the first 20cm – 8″ of the protective backing from the new sightline strip.
Evolution3 FreeHand User Guide Apply the sightline strip in stages from one end of the cutter bar to the other using the yellow silicone grip as your guide; the back edge of the sightline strip should be touching the front edge of the silicone grip. TIP: Remove the protective backing from the double-sided tape in stages to prevent complications during application. Ensure that the sightline strip does not overlap the silicone grip as this will affect the clamping of the cutter bar.
Evolution3 FreeHand User Guide The sightline strip is wider than it needs to be and requires trimming to suit cutting line of the machine. Use the Double Graphik tool head to gently cut through the sightline strip in 3 to 4 passes. This will ensure the sightline strip is not distorted and indicates the blades line of cut accurately. TIP: Order replacement strips (or check stock) whenever you change the strip to save running out. The world’s finest cutting machines www.keencut.
