Users Manual

ManualsBrandsKeekoonvision Technology ManualsPet AccessoriesSmart Pet Feeder

5. If the App asks for the location permission of your mobile phone,

please allow it. The name of your Wi-Fi network will then appear in the

textbox automatically.

Please note that the feeder does not support 5Ghz Wi-Fi networks, but

only 2.4Ghz networks. Please check that the Wi-Fi name is the name of

a 2.4Ghz Wi-Fi network. If not, please switch the mobile phone's Wi-Fi

network to a 2.4Ghz Wi-Fi network.

Next, please enter the corresponding Wi-Fi password and click

Confirm.

Important Notice:

a. Please choose a 2.4Ghz Wi-Fi signal instead of a 5Ghz signal. The

feeder does not support 5Ghz Wi-Fi networks.

b. When entering the password, be aware that it is case sensitive.

c. Please choose a Wi-Fi network with WPA or WPA2 encryption

instead of WEP encryption.

d. Make sure that MAC address filtering and wireless device isolation is

turned off on the wireless router.

e. The feeder may not support the Wi-Fi signal of the wireless repeater.

If the connection fails, try connecting to the wireless router.

6. The App will then ask you to scan a QR code that contains your Wi-Fi

Summary of content (14 pages)

PAGE 1
5. If the App asks for the location permission of your mobile phone, please allow it. The name of your Wi-Fi network will then appear in the textbox automatically. Please note that the feeder does not support 5Ghz Wi-Fi networks, but only 2.4Ghz networks. Please check that the Wi-Fi name is the name of a 2.4Ghz Wi-Fi network. If not, please switch the mobile phone's Wi-Fi network to a 2.4Ghz Wi-Fi network. Next, please enter the corresponding Wi-Fi password and click Confirm. Important Notice: a.
PAGE 2
information with the feeder's camera. Click Continue, then put the QR code in front of the feeder's camera. Please place the phone about 20 to 30 centimeters in front of the camera and wait a few seconds until you hear a tone. Then click I Heard a Prompt. 7. The feeder will then try to connect to the Wi-Fi network. When connected, click Done to complete the adding process. If the feeder fails to connect, please check the important notice above.
PAGE 3
8. The App will be then directed to the video interface for the pet feeder. Advanced settings WLAN signal Listen to feeder Full screen Switch video resolution Speak to pet feeder Take snapshot to phone Record to phone Check snapshots and video records in phone; only available for android phones. Play videos back in SD card Set up feeding plan Notice: a. The WLAN signal shows on video is only for checking the internal network's status. It does not represent the internet connection's status. b.
PAGE 4
switch the Wi-Fi indicator's flashing status to flashing slowly. 2. Please check the name of the 2.4Ghz Wi-Fi network and enter the password in the same way as in QR code mode. Click Confirm and the App will ask you to switch your mobile phone's Wi-Fi network to a new network broadcast by the feeder. 3. Please go to Wi-Fi settings on the mobile phone and connect to the Wi-Fi which starts with SmartLife- . No password is necessary. Return to the App after the Wi-Fi is connected.
PAGE 5
Add pet feeder via Auto Scan mode Please note that in auto scan mode, 100% success rate of connecting the feeder to the Wi-Fi network cannot be guaranteed. Choose Auto Scan Mode on the Wi-Fi pet feeder page and enter the correct name and password of the 2.4GHz Wi-Fi network. Make sure the feeder's indicator LED is flashing RED rapidly. Wait for the feeder to connect to the Wi-Fi network and appear in the App.
PAGE 6
Feeding Manual feeding 1. Click Feed in live video page. Choose the feeding portions and click Feed. The feeder will feed immediately. 2. You can also click the Manual feed button on the feeder to feed manually.
PAGE 7
Timed feeding 1. The pet feeder supports the scheduled feeding of exact portions at exact times. Click the Feeding Plan button , click Add timing, choose Feeding time, Repeat rules for each day of the week, and Feed portions, then click Save. 2. The feeder supports up to 12 feeding schedules. If you need to disable a schedule, you can disable it by disabling its switch. You can also delete it by long pressing the feeding schedule to access the delete option.
PAGE 8
Feeding voice recording 1. To develop good feeding habits for pets, the feeder supports pre-recording a maximum of 10 seconds of audio, which is played during feeding. 2. Click the Feeding audio button on the manual feed page, then start talking near the microphone of the feeder. The feeder will start recording your voice. When you want to stop, click the Feeding audio button again, or wait for 10seconds when it stops automatically.
PAGE 9
the pet feeder will work as scheduled in the feeding plan. Otherwise, it will stop feeding if the pets still do not finish feeding after 10 minutes. The feeder cannot operate until feeding resumes. c. The voice recording will not play when feeding by button and battery supply only. Feeding records and alarm 1. After feeding, there will be feeding records in the App. Click Feeding record on the manual feed page to check the feeding records.
PAGE 10
Others Advanced settings Click to access the advanced settings page. Device information: Check feeder information. Please make sure that the time zone of the feeder is correct. It should be same as the mobile phone's time zone when adding the feeder. If it is incorrect, the feeder may feed at incorrect times, so please remove the feeder and add it again.
PAGE 11
Tap-to-Run and Automation: It is not suitable for this feeder, please ignore it. Basic Function Settings: In basic function settings, you can turn indicators on/off. Notice that when feeder is feeding, the power indicator will flash even if it is turned off. You can turn on/off the timestamp shown in the live video. You can also switch talk mode to 2-way audio communication. IR Night Vision: Turn on/off/auto the IR night LED.
PAGE 12
with the new account. Please make sure that both accounts are in the same country or area when registering them. Remove Device: You can re-configure the feeder's Wi-Fi network and restore the feeder to factory default settings with this option. Battery The back-up battery is designed as a short-term alternative for when the external power supply is cut. With battery supply only, when the feeder reaches the time set for timed feeding, the feeder will feed as normal.
PAGE 13
Reset When you want to reset the feeder to factory default settings, turn on the feeder with external power and wait for it to boot up. Long press the Wi-Fi settings button for 5 seconds until you hear a prompt voice. Then the feeder will reset to factory default settings FAQ Q1: Why did the feeder fail to connect to my Wi-Fi network? A: Please check the important notice on Page 6 for help. You can try to add the feeder via AP mode instead of QR code mode and auto scan mode.
PAGE 14
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.